The authors thank Dr J. J. van der Klink for the assistance in the choice and assembly of the equipment, as well as Dr F. Kateb and Dr G. Bertho for useful discussions. A.C. was supported by the Swiss National Science Foundation (grant PPOOP2_157547). We acknowledge financing from Paris Sorbonne Cit&#233; (NMR@Com, DIM Analytics, Ville de Paris, the Fondation de la Recherche M&#233;dicale (FRM ING20130526708), and the Parteneriat Hubert Curien Brancusi 32662QK. Our team is part of Equipex programs Paris-en-R&#233;sonance and CACSICE.

NOTE: All data analysis was performed using commercial software.
1. Prepare the Polarizing Solution
<ol>
	<li>Prepare 2 ml of a 1.12 M 13C-labeled sodium pyruvate (Na+[CH3-CO-13COO]-, substrate) solution doped with 33 mM of TEMPOL radical (4-hydroxy-2,2,6,6-tetramethylpiperidin-1-oxyl, polarizing agent)4 in 2:1 D2O/d6-ethanol for 13C observations. CAUTION: Handling precautions must be taken due to the flammable nature of d6-ethanol.</li>
	<li>Verify that the radical concentration is optimal in terms of achieved polarization.
	<ol>
		<li>Change slightly the radical concentration of the solution at point 1.1 (e.g., to 30 mM or 35 mM).</li>
		<li>Determine iteratively the solid-state enhancement (see Step 3) and find the radical concentration that leads to the maximum enhancement.</li>
	</ol>
	</li>
</ol>
2. Polarization
<ol>
	<li>Lower the DNP cryostat temperature through the cooldown procedure. Click the &#39;Cooldown&#39; button on the cryostat software interface (Figure 2D).</li>
	<li>Collect liquid helium in the DNP cryostat through the filling procedure. Click the &#39;Filling&#39; button on the cryostat software interface (Figure 2D).</li>
	<li>Place 300 &#956;l of the optimized polarizing solution from Step 1.1 in the sample container provided with the DNP polarizer. Freeze the sample container with the sample inside by gently immersing it in a liquid nitrogen bath.</li>
	<li>Eliminate the liquid nitrogen that may be present in the sample container after the freezing procedure (Step 2.3) by extracting the sample container from the liquid nitrogen bath and rotating it upside down. &#160; 
	NOTE: This step is crucial to obtain a thorough dissolution of the sample (see Step 5).</li>
	<li>Insert the sample into the cryostat. &#160; 
	NOTE: This Step, composed of the following sub-step, must be performed rapidly (i.e., in less than 10-20 sec) to prevent the sample from melting.
	<ol>
		<li>Insert the sample container in the sample holder. Insert the sample holder in the main cryostat insert. Insert the microwaves waveguide in the sample holder.</li>
	</ol>
	</li>
	<li>Lower the cryostat temperature by starting the 1 K cooling procedure. Click the &#39;1K Cooling&#39; button on the cryostat software interface (Figure 2D).</li>
	<li>Turn the microwave source on and irradiate the sample. Click the &#39;MW-ON&#39; button on the cryostat software interface (Figure 2D).</li>
</ol>
3. Solid-state NMR Measurements
<ol>
	<li>Disconnect the coaxial cable of the NMR console detection channel from the spectrometer coil by rotating the connector anticlockwise by 90&#176; and pulling it. Plug the coaxial cable of the detection channel to the coaxial connector of the cryostat NMR coil. Insert the male connector of the NMR console cable in the female connector of the cryostat NMR coil, paying attention to the orientation pin; push firmly and rotate the connector clockwise by 90&#176;.</li>
	<li>Measure the NMR thermal signal in the solid-state at the cryostat site using a simple pulse-acquire sequence with un-calibrated low flip-angle pulses repeated at an interval of T = 5 min. After setting up the measurement, write in the command line of the software &#39;zg&#39; and press the &#39;Enter&#39; keyboard key. Refer to NMR spectrometer operation manual for further details on spectrometer operation and measurement setup.</li>
	<li>Measure the DNP-enhanced NMR signal. Repeat operations of step 3.2 after initiating the DNP process as described in Section 2.</li>
	<li>Disconnect the NMR console detection channel coaxial cable from the cryostat NMR coil by rotating the connector anticlockwise by 90&#176; and pulling it. Plug the coaxial cable of the detection channel to the coaxial connector of the spectrometer coil. Insert the male connector of the NMR console cable in the female connector of the spectrometer coil, paying attention to the orientation pin; push firmly and rotate the connector clockwise by 90&#176;.</li>
</ol>
4. Optimize the Homogeneity of the Main Magnet Field (&#39;Shimming&#39;)
<ol>
	<li>Place in the spectrometer a tube containing 500 &#956;l of mixture produced in previous experiments (i.e., after Step 6.2).</li>
	<li>Perform NMR spectrometer shimming by varying the current in the shimming gradient coils searching for the maximum &#39;lock&#39; signal of deuterium. Select the relevant shimming coil by pushing the corresponding button on the NMR console.
	<ol>
		<li>Rotate the knob on the NMR console to determine the rotation direction that increases the lock signal. Continue to rotate until the signal reaches a maximum. Select another shimming coil and repeat the maximization until a local maximum for all the shimming coils is found. Refer to NMR spectrometer operation manual for further details. At the end, remove the sample used for locking.</li>
	</ol>
	</li>
</ol>
5. Dissolution
<ol>
	<li>Insert 5 ml of D2O in the dissolution insert boiler. Pressurize and heat the D2O by means of the resistive wire until T&#160;&#8776; 180-200 &#176;C is reached. Click the &#39;Prepare Heater&#39; button on the cryostat software interface (Figure 2D).</li>
	<li>After completion of the sample polarization procedure (e.g., after 3 TDNP), pressurize the cryostat slightly above room pressure. Click the &#39;SS Operations&#39; button on the cryostat software interface (Figure 2D). Remove the microwave guide from the dissolution insert.</li>
	<li>Slide the dissolution insert (Figure 3B) down into the sample holder (Figure 3A-c). The dissolution insert has to reach the bottom of the sample holder and must be pushed firmly to make a leaktight connection with the sample container in order to avoid D2O leaking in the cryostat.</li>
	<li>Press the hardware trigger (Figure 3C-h) to begin the dissolution sequence, a pre-determined timed sequence of pneumatic valves operations.</li>
</ol>
6. Injection
<ol>
	<li>Before dissolution place a 5 mm NMR tube, containing 500 &#956;l sample (e.g., D2O for <img alt="Equation13" src="/files/ftp_upload/53548/53548equation13.jpg" width="29" /> measurement in Step 7 or LDH solution from Step 8 for enzymatic activity measurements in Step 9), in the isocenter of the 11.74 T NMR spectrometer (see Step 4).</li>
	<li>Just after the dissolution (Step 5), mix 500 &#956;l of hyperpolarized solution with the sample placed in the NMR spectrometer in Step 6.1.
	<ol>
		<li>Manual Injection: collect the hyperpolarized solution at the end of a 2.5 m long transfer tube in a glass beaker placed close to the NMR spectrometer magnet. Manually inject 500 &#956;l of hyperpolarized solution in the NMR sample tube through a custom made capillary system.</li>
		<li>Automatic injection: before the dissolution process, connect the transfer tube to an automated custom made injection device that separates the hyperpolarized solution from the helium gas used for transfer. The device automatically delivers 500 &#956;l of hyperpolarized solution into the sample tube.</li>
	</ol>
	</li>
</ol>
7. Liquid-state NMR Measurement
<ol>
	<li>After the dissolution, measure the NMR hyperpolarized signal from the sample in the spectrometer by a series of 10&#176; flip angle pulse-acquire sequences spaced by 1.5 sec to follow the progression of magnetization of the substrate (A) and the product (B). After setting up the measurement, write in the command line of the software &#39;zg&#39; and press the &#39;Enter&#39; keyboard key. Refer to NMR spectrometer operation manual for further details on spectrometer operation and measurement setup.</li>
	<li>Once the magnetization is fully relaxed (i.e., after T = 10 T1), measure the NMR thermal signal by a series of 90&#176; flip angle pulse-acquire sequences spaced by T = 3 T1&#160;&#8776; 3 min. After setting up the measurement, write in the command line of the software &#39;zg&#39; and press the &#39;Enter&#39; keyboard key. Refer to NMR spectrometer operation manual for further details on spectrometer operation and measurement setup.</li>
</ol>
8. Preparation of Enzyme-containing Samples (Specific for the Pyruvate-to-lactate Transformation)
<ol>
	<li>Prepare the reaction buffer with the following recipe: 50 mM reduced nicotinamide adenine dinucleotide (NADH), 1 mM ethylene-diaminetetraacetic acid (EDTA), 0.1 mM dithiothreitol (DTT) in 0.1 M phosphate buffer, pH = 7.0.</li>
	<li>Prepare a rabbit muscle LDH solution 1 U/ml prepared freshly in reaction buffer with 20 &#956;g/ml bovine serum albumin, BSA.</li>
	<li>Mix 478 &#956;l reaction buffer (Step 8.1), 20 &#956;l D2O to allow for spectrometer field stabilization (&#39;locking&#39;) and 2 &#956;l LDH solution (Step 7.2).</li>
	<li>Place the 500 &#956;l solution volume prepared in Step 8.3 into a 5 mm NMR tube and position the tube into the 500 MHz NMR spectrometer.</li>
</ol>
9. Complete Enzymatic Reaction Rate Measurement Procedure
<ol>
	<li>Prepare the polarizing sample (Step 1) and polarize it (Step 2).</li>
	<li>Perform shimming on the spectrometer (Step 4) and prepare the enzymatic sample (Step 8).</li>
	<li>Perform the dissolution (Step 5) and the injection (Step 6).</li>
	<li>Measure a series of signals from the hyperpolarized sample with 10&#176; flip angle pulses acquisitions spaced by 1.5 sec (Step 7). This step allows measuring the hyperpolarized signal decay and the signal buildup of metabolites.</li>
</ol>
10. Fitting
<ol>
	<li>For each spectrum acquired in Step 9.4, identify the peaks corresponding to substrate (A) and product (B) respectively and integrate them (determine the area of the peaks). The peaks integrals give the magnetization time course signals (M(A,B)(t), see equation 2).</li>
	<li>Using the solution of equation (2), determine the value of F = (RA + keff ) from a simple exponential fit of the substrate signal integrated in Step 10.1.</li>
	<li>Using the value F = (RA + keff ) determined in Step 10.2, determine keff and RB from a fit of the product signal MB(t) with the function obtained by integrating equation (2). Refer to Representative results section (Enzymatic activity and metabolic measurements) for details on the reaction modeling, fitting and rf correction.</li>
</ol>

<ol>
	<li>Overhauser, A. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Polarization+of+Nuclei+in+Metals.">Polarization of Nuclei in Metals.</a> Phys. Rev. 92 (2), 411-415 (1953).</li><li>Abragam, A., Goldman, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Principles+of+dynamic+nuclear+polarisation.">Principles of dynamic nuclear polarisation.</a> Rep. Prog. Phys. 41 (3), 395 (1978).</li><li>Wolber, J., Ellner, F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Generating+highly+polarized+nuclear+spins+in+solution+using+dynamic+nuclear+polarization.">Generating highly polarized nuclear spins in solution using dynamic nuclear polarization.</a> Nuc. Inst. Met. Phys. Res. Sec. A. 526 (1-2), 173-181 (2004).</li><li>Cheng, T., Capozzi, A., Takado, Y., Balzan, R., Comment, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Over+35%+liquid-state+13C+polarization+obtained+via+dissolution+dynamic+nuclear+polarization+at+7+T+and+1+K+using+ubiquitous+nitroxyl+radicals.">Over 35% liquid-state 13C polarization obtained via dissolution dynamic nuclear polarization at 7 T and 1 K using ubiquitous nitroxyl radicals.</a> PCCP. 15 (48), 20819-20822 (2013).</li><li>Ardenkjaer-Larsen, J. H., Fridlund, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Increase+in+signal-to-noise+ratio+of+&gt;+10,000+times+in+liquid-state+NMR.">Increase in signal-to-noise ratio of &gt; 10,000 times in liquid-state NMR.</a> PNAS. 100 (18), 10158-10163 (2003).</li><li>Day, S. E., Kettunen, M. I., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Detecting+tumor+response+to+treatment+using+hyperpolarized+13C+magnetic+resonance+imaging+and+spectroscopy.">Detecting tumor response to treatment using hyperpolarized 13C magnetic resonance imaging and spectroscopy.</a> Nat. Med. 13 (11), 1382-1387 (2007).</li><li>Keshari, K. R., Wilson, D. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hyperpolarized+[2-13C]-Fructose:+A+Hemiketal+DNP+Substrate+for+In+Vivo+Metabolic+Imaging.">Hyperpolarized [2-13C]-Fructose: A Hemiketal DNP Substrate for In Vivo Metabolic Imaging.</a> JACS. 131 (48), 17591-17596 (2009).</li><li>Zeng, H., Lee, Y., Hilty, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+Rate+Determination+by+Dynamic+Nuclear+Polarization+Enhanced+NMR+of+a+Diels&#8722;Alder+Reaction.">Quantitative Rate Determination by Dynamic Nuclear Polarization Enhanced NMR of a Diels&#8722;Alder Reaction.</a> An. Chem. 82 (21), 8897-8902 (2010).</li><li>Harrison, C., Yang, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Comparison+of+kinetic+models+for+analysis+of+pyruvate-to-lactate+exchange+by+hyperpolarized+13C+NMR.">Comparison of kinetic models for analysis of pyruvate-to-lactate exchange by hyperpolarized 13C NMR.</a> NMR in Biom. 25 (11), 1286-1294 (2012).</li><li>Allouche-Arnon, H., Gamliel, A., Sosna, J., Gomori, J. M., Katz-Brull, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+vitro+visualization+of+betaine+aldehyde+synthesis+and+oxidation+using+hyperpolarized+magnetic+resonance+spectroscopy.">In vitro visualization of betaine aldehyde synthesis and oxidation using hyperpolarized magnetic resonance spectroscopy.</a> Chem. Comm. 49 (63), 7076-7078 (2013).</li><li>Lerche, M. H., Meier, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+dynamic+nuclear+polarization-NMR+on+blood+plasma+for+assays+of+drug+metabolism.">Quantitative dynamic nuclear polarization-NMR on blood plasma for assays of drug metabolism.</a> NMR in Biom. 24 (1), 96-103 (2011).</li><li>Nelson, S. J., Kurhanewicz, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Metabolic+Imaging+of+Patients+with+Prostate+Cancer+Using+Hyperpolarized+[1-13C]Pyruvate.">Metabolic Imaging of Patients with Prostate Cancer Using Hyperpolarized [1-13C]Pyruvate.</a> Sci. Trans. Med. 5 (198), 198ra108 (2013).</li><li>Kurhanewicz, J., Vigneron, D. B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Analysis+of+Cancer+Metabolism+by+Imaging+Hyperpolarized+Nuclei:+Prospects+for+Translation+to+Clinical+Research.">Analysis of Cancer Metabolism by Imaging Hyperpolarized Nuclei: Prospects for Translation to Clinical Research.</a> Neoplasia. 13 (2), 81-97 (2011).</li><li>Comment, A., Merritt, M. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hyperpolarized+Magnetic+Resonance+as+a+Sensitive+Detector+of+Metabolic+Function.">Hyperpolarized Magnetic Resonance as a Sensitive Detector of Metabolic Function.</a> Biochem. 53 (47), 7333-7357 (2014).</li><li>Carravetta, M., Johannessen, O. G., Levitt, M. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Beyond+the+T-1+limit:+Singlet+nuclear+spin+states+in+low+magnetic+fields.">Beyond the T-1 limit: Singlet nuclear spin states in low magnetic fields.</a> PRL. 92 (15), 153003 (2004).</li><li>Carravetta, M., Levitt, M. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Theory+of+long-lived+nuclear+spin+states+in+solution+nuclear+magnetic+resonance.+I.+Singlet+states+in+low+magnetic+field.">Theory of long-lived nuclear spin states in solution nuclear magnetic resonance. I. Singlet states in low magnetic field.</a> J. Chem. Phys. 122 (21), 214505 (2005).</li><li>Vasos, P. R., Comment, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Long-lived+states+to+sustain+hyperpolarized+magnetization.">Long-lived states to sustain hyperpolarized magnetization.</a> PNAS. 106 (44), 18469-18473 (2009).</li><li>Claytor, K., Theis, T., Feng, Y., Warren, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measuring+long-lived+13C2+state+lifetimes+at+natural+abundance.">Measuring long-lived 13C2 state lifetimes at natural abundance.</a> JMR. 239, 81-86 (2014).</li><li>Pileio, G., Carravetta, M., Hughes, E., Levitt, M. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+long-lived+nuclear+singlet+state+of+N-15-nitrous+oxide+in+solution.">The long-lived nuclear singlet state of N-15-nitrous oxide in solution.</a> JACS. 130 (38), 12582-12583 (2008).</li><li>Stevanato, G., Hill-Cousins, J. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Nuclear+Singlet+Lifetime+of+More+than+One+Hour+in+Room-Temperature+Solution.">A Nuclear Singlet Lifetime of More than One Hour in Room-Temperature Solution.</a> Ange. Chem. Int. Ed. 54 (12), 3740-3743 (2015).</li><li>Ghosh, R. K., Kadlecek, S. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measurements+of+the+Persistent+Singlet+State+of+N(2)O+in+Blood+and+Other+Solvents-Potential+as+a+Magnetic+Tracer.">Measurements of the Persistent Singlet State of N(2)O in Blood and Other Solvents-Potential as a Magnetic Tracer.</a> MRM. 66 (4), 1177-1180 (2011).</li><li>Harris, T., Eliyahu, G., Frydman, L., Degani, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Kinetics+of+hyperpolarized+13C1-pyruvate+transport+and+metabolism+in+living+human+breast+cancer+cells.">Kinetics of hyperpolarized 13C1-pyruvate transport and metabolism in living human breast cancer cells.</a> PNAS. 106 (43), 18131-18136 (2009).</li><li>Comment, A., van den Brandt, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+and+performance+of+a+DNP+prepolarizer+coupled+to+a+rodent+MRI+scanner.">Design and performance of a DNP prepolarizer coupled to a rodent MRI scanner.</a> Conc. Mag. Res. B. 31 (4), 255-269 (2007).</li><li>Balzan, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Methods for Molecular Magnetic Resonance Imaging and Magnetic Resonance Spectroscopy using Hyperpolarized Nuclei. 5966, 1-140 (2013).</li><li>Bornet, A., Melzi, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Boosting+Dissolution+Dynamic+Nuclear+Polarization+by+Cross+Polarization.">Boosting Dissolution Dynamic Nuclear Polarization by Cross Polarization.</a> JPC Letters. 4 (1), 111-114 (2013).</li><li>Bowen, S., Hilty, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rapid+sample+injection+for+hyperpolarized+NMR+spectroscopy.">Rapid sample injection for hyperpolarized NMR spectroscopy.</a> PCCP. 12 (22), 5766-5770 (2010).</li><li>Cavadini, S., Vasos, P. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Singlet+states+open+the+way+to+longer+time-scales+in+the+measurement+of+diffusion+by+NMR+spectroscopy.">Singlet states open the way to longer time-scales in the measurement of diffusion by NMR spectroscopy.</a> Conc. Mag. Res. A. 32 (1), 68-78 (2008).</li><li>Ahuja, P., Sarkar, R., Vasos, P. R., Bodenhausen, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Long-lived+States+in+Multiple-Spin+Systems.">Long-lived States in Multiple-Spin Systems.</a> Chem. Phys. Chem. 10 (13), 2217-2220 (2009).</li><li>Ahuja, P., Sarkar, R., Jannin, S., Vasos, P. R., Bodenhausen, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Proton+hyperpolarisation+preserved+in+long-lived+states.">Proton hyperpolarisation preserved in long-lived states.</a> Chem. Comm. 46 (43), 8192-8194 (2010).</li><li>Sarkar, R., Comment, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Proton+NMR+of+15N-Choline+Metabolites+Enhanced+by+Dynamic+Nuclear+Polarization.">Proton NMR of 15N-Choline Metabolites Enhanced by Dynamic Nuclear Polarization.</a> JACS. 131 (44), 16014-16015 (2009).</li></ol>

The authors declare that they have no competing financial interests

The critical points of the dissolution DNP NMR experiment are: (i) the level of polarization attained for the substrate, which determines the lowest product concentration necessary for experiments as well as the number of signal acquisitions that can be performed and (ii) the lifetimes of magnetization, compared to the duration of the transfer between the polarization and the detection sites and to the rate of substrate transformation. The injection system of the dissolution DNP setup herein described allows for sample transfer in as little as 3-4 sec. Although the transfer was not as rapid as in the method proposed by S. Bowen and C. Hilty,26 polarization losses for pyruvate were limited due to the moderate longitudinal relaxation in the low field. [1-13C]pyruvate, with its long carboxylic nuclear T1, allows measuring the flux through LDH at concentrations as low as 10-3 U/ml.
The high signal-to-noise ratio obtained using dissolution DNP suggests that one could be sensitive to even lower [1-13C]pyruvate concentrations, and lower enzymatic conversion rates. The achieved polarization level affords more than 200 experiments with a significant signal-to-noise ratio to be acquired in the liquid-state NMR spectrometer using a low flip angle &#945; = 10&#176;. This leaves room for optimization both in terms of repetition times and flip angles. For the build-up of polarization in the solid-state some molecules polarize well with some polarizing agents (TEMPO, OXO63)4 and others do not, for reasons that are not yet fully understood. Experimental trials are the only way to determine whether the polarization step is successful. To improve the polarization level, one can explore the use of different radical species4 and the application of different techniques relying on &#39;cross-polarization&#39;.25
Further optimization of radical and substrate concentrations as well as the solvent composition in the DNP sample can be tried to improve polarization. The technique is limited to molecules in which a nucleus or a group of nuclei able to sustain polarization after dissolution can be identified. Polarization can be sustained either as an imbalance between mono-nuclear eigenstates in high magnetic fields or in the form of LLS delocalized on two or more coupled nuclei. For the first option, the probe nucleus has to be distant from other nuclei with high gyromagnetic ratios, such as protons. If such a position is not found naturally, enrichment in NMR-active nuclei at isolated sites in the molecule or replacement of protons in the vicinity of active nuclei by deuterons, to lower the magnetic dipole strength, are necessary. To obtain LLS, a theoretical analysis of the magnetic couplings within groups of nuclei can be carried out27,28 in order to find optimal means to support polarization. This strategy has proved successful in small molecules such as aminoacids29 and can be applied to other molecules involved in metabolic cycles of interest. To better preserve magnetization during the experiment, the combination of dissolution DNP with excitation of LLS promises to extend the measurement time span for other enzymatic reactions.20
The DNP-NMR experiment described here is adapted for the measurement of pyruvate metabolism in cancer cells.6 The real-time measurement of enzymatic activity by dissolution DNP enhanced NMR can help current efforts in cancer diagnosis by DNP-enhanced MRI, already used in the clinic.12 The molecular specificity of DNP-enhanced NMR makes it a method of choice for distinguishing between molecular targets and the products of their transformations. Future improvements will focus on the assessment of other molecular tracers for metabolic transformations30 susceptible to be relevant for MRI diagnostics, as well as on obtaining extended observation time windows.

Dynamic nuclear polarization (DNP),1,2 a technique designed to enhance the nuclear spin polarization, i.e., the imbalance between &#39;up&#39; and &#39;down&#39; spin populations (P = [N&#8593; - N&#8595;] / [N&#8593; + N&#8595;]), was first introduced in the 1950&#39;s. Nuclear spins such as 13C can be polarized up to P = 10-1 in favorable conditions, typically at a temperature on the order of 1 K and in a magnetic field of 3.357 T.3,4 A breakthrough for biological applications came in the early 2000&#39;s with the development of dissolution DNP which consists in dissolving frozen polarized samples in superheated water while retaining the high nuclear polarization level obtained at low temperature.5 The liquid-state NMR signal is enhanced by a factor 103-104 as compared to common thermally-polarized RT NMR conditions. Dissolution DNP therefore provides a way to non-invasively measure biochemical reaction rates in situ in realtime, allowing monitoring dynamics by NMR with a temporal resolution of 1 sec or less.6-10 It also became possible to detect analytes in very low concentrations.11
Among the non-invasive molecular imaging modalities, hyperpolarized NMR is the only technique that allows simultaneously measuring a substrate and its metabolic products in real-time. Dissolution DNP was received with enthusiasm in various scientific areas ranging from in vitro NMR to clinical MRI12 and the most promising applications are related to the in situ monitoring of metabolism.13,14 The main limitation of dissolution DNP is that, after a time on the order of five times the longitudinal relaxation time constant T1, the enhanced polarization is lost. It is therefore necessary to use molecules bearing nuclear spins exhibiting relatively long T1. To extend the time-span of the polarization enhancement, slowly-relaxing nuclear spin states, known as long-lived states (LLS), may be used.15-17 LLS are insensitive to the intra-pair dipole-dipole interaction, so their characteristic relaxation time constant, TLLS, can be much longer than T1.18 A magnetization lifetime of tens of minutes and up to 1 hr could therefore be obtained,19,20 and LLS have been proposed for both magnetic resonance spectroscopy (MRS) and MRI.21
The main points that need to be carefully optimized for studying enzymatic reaction rates by hyperpolarized NMR are: (i) maximize the solid-state polarization and (ii) minimize the polarization loss during the transfer of the hyperpolarized solution from the polarizer to the NMR spectrometer. This article describes the adaptation of a custom-made dissolution DNP apparatus and injection system to study enzymatic reactions. The characteristics and performance of the setup will be demonstrated with the well-known and widely-used hyperpolarized substrate [1-13C]pyruvate. The main reasons for this choice are, first, its naturally long 13C longitudinal relaxation time (T1 &#62;50 sec at high magnetic fields and temperatures above 293 K) which allows monitoring reactions during several minutes, and, second, its central role in cancer metabolism.13,14 Using dissolution DNP NMR and a custom-developed injection system, the oxidation of pyruvate catalyzed by lactate dehydrogenase (LDH) can be monitored in presence of an initial pool of unlabelled lactate9,22 or with no unlabelled lactate added, as shown here. It has been shown that the [1-13C]lactate signal measured in vivo (including in cells) following the injection of hyperpolarized [1-13C]pyruvate is mainly due to a fast label exchange between pyruvate and lactate rather than to lactate production.6
We herein present the real-time production of [1-13C]lactate from hyperpolarized [1-13C]pyruvate injected into a NMR tube containing LDH but initially no lactate.
System description 
There are two main parts in a dissolution DNP setup (Figure 1): the DNP polarizer and the NMR spectrometer. The main element of the DNP polarizer is a cryostat to cooling the sample to around 1 K in a pumped helium bath. The cryostat is inserted in a 3.35 T superconductive magnet and has a geometry that guarantees to have the polarizing sample at the isocenter of the magnet (Figure 1). Inside the cryostat, the sample (a) is surrounded by a NMR coil (b), to measure the polarization buildup, contained in an overmoded microwave cavity (c). The whole sample is kept at low temperature in a pumped helium bath (d) and irradiated with microwaves through the waveguide. The whole system is managed by custom-made software (Figure 2D).
The hardware and cryogenic equipment needed to perform DNP and the subsequent dissolution are still a technological challenge. A new DNP cryostat23,24 was developed and tested to determine its cryogenic performances and then optimized for fast cool-down, helium hold-time and overall minimal helium consumption during operation.
The cryostat consists of two parts. The first part of the cryostat is the insulation dewar (Figure 2A) that can be roughly separated in top part (a) the tail, or sample space (b), and the outer vacuum chamber (OVC) kept under high vacuum and housing the radiation screens (c). The second part of the cryostat is the main insert (Figure 2B), placed into the insulation dewar, where all the flow regulations are managed. The liquid helium coming from the external storage dewar through the transfer line (a), is in the first stage condensed in the separator (b), an intermediate chamber used both to keep the top part of the cryostat cold and to remove the helium evaporated during the transfer. The separator pressure is lowered by pumping through a capillary (c) wrapped around the top part of the cryostat; the flow of cold helium in this capillary is used to cool down the baffles (d) and the radiation screens in the insulation dewar (OVC). The sample is placed and polarized in the sample space. The sample space is connected to the separator through another capillary (e), wrapped around the tail of the main cryostat insert. This capillary can be opened or closed through a needle valve manually operated from outside.
To achieve the low temperature used during the DNP process, liquid helium needs to be collected in the cryostat sample space and its pressure lowered to the mbar range. The operations needed for cryostat operation are performed through a rather complex pumping system with three sets of pumps, monitored and operated in different points with electronic and electro-mechanic instruments (Figure 2C). The cryostat OVC needs to be pumped to high vacuum by the first pumping system. This system is composed of a turbo-molecular pump backed up by a rotary pump (a). The liquid helium is transferred from the storage dewar (b) through the cryostat transfer line inlet to the cryostat separator. The separator has an outlet connected to the second pumping set. This set is composed of a 35 m3/hr membrane pump (c). This line allows removing the helium gas boiled during the transfer from the dewar and during separator cooling. The liquid helium collected in the separator can then be transferred to the sample space through the capillary tubes described above. To transfer liquid helium from the separator to the sample space and subsequently to lower sample space pressure to mbar range, a third pumping system composed of a 250 m3/hr Roots pump backed up by a 65 m3/hr rotary pump (d) is connected to the cryostat through a manual butterfly valve (e).
All the vacuum system operations are controlled and regulated by an electropneumatic custom-made device (f). This device controls vacuum line connections between the cryostat separator (g) and sample space (h) outlets, the second/third pumping systems (c, d), a compressed helium bottle (i) and the outside. Communication between (f) and the outside passes through a one-way valve (j). The electro-pneumatic device (f) as well as all the system parameters and the dissolution hardware are controlled and operated by a custom-made electronic device interfaced USB with a common PC. Finally all the system, through the electronic device, is managed by custom-made standalone software (Figure 2D) where relevant operations are launched through an interface using software buttons.
To manage the sample and measure NMR signal build-up in the solid state a series of inserts are used (Figure 3A). To prepare the cryostat for polarization, place the main sample insert (a), into the cryostat. The main sample insert is provided with an NMR coil (b) placed inside an overmoded gold-plated microwave cavity. Pre-freeze the substrate containing solution to be polarized (polarizing solution) at liquid nitrogen temperature in a suitable sample container and place it at the end bottom of the fiberglass sample holder (c). Slide the sample holder into the main sample insert to reach the magnet isocenter. Insert the gold-plated waveguide (d) in the sample holder. The waveguide allows the microwave generated from an external microwave source to travel with minimal losses to the sample.
The custom-made software for cryostat management handles automatically, upon clicking the corresponding interface button, different operations like cooldown (the cryostat temperature is lowered close to liquid helium temperature), filling (the cryostat is filled with liquid helium to a pre-determined level), an additional step of cooling to T&#160;&#8776; 1 K (the liquid helium bath is pumped to achieve the lowest temperature possible), pressurization (the cryostat is pressurized slightly above room pressure at P = 10-30 mbar to allow cryostat opening without risks of contamination of the cryostat by air) and dissolution (automatic procedure to dissolve the DNP sample and transfer the resulting hyperpolarized solution to the measurement site, i.e., the NMR spectrometer).
The polarization is performed irradiating the sample with microwaves at 94 GHz (in a polarizing field B0 = 3.35 T). A sample is considered completely polarized after 3 TDNP, where TDNP is the polarization buildup time. TDNP is of the same order of magnitude as the longitudinal relaxation time of the target nuclei in solid state at the given field and temperature. In all our experiments the sample was polarized for more than 5 TDNP.
At the end of the polarization time, the sample has to be dissolved in a RT solution in order to be used for measurement of enzymatic activity. During the dissolution process, 5 ml of superheated D2O from the boiler of the dissolution insert (Figure 3B) are pushed by compressed helium gas (P = 6-8 bar) to reach the DNP-enhanced sample and dissolve it. The resulting hyperpolarized solution is pushed out the dissolution insert by the compressed helium gas, through the dissolution insert outlet (Figure 3C-b), a 2 mm inner diameter Teflon transfer tube. The time needed for the dissolution process is 300 msec.23 The time needed for the sample transfer from the DNP polarizer to the NMR spectrometer site is about 3 sec.
The dissolution process is performed using a dissolution insert (Figure 3B). The dissolution insert is composed of an electronic-pneumatic assembly (a), a carbon fiber stick (b) containing connection tubes between the boiler in the pneumatic assembly and the sample container locker (c), which allows leak-tight coupling with the sample container, and back out to the outlet. The electro-pneumatic assembly (Figure 3C) is used to produce and drive superheated D2O through the carbon fiber stick to the sample container and then to extract the hyperpolarized solution from the cryostat. The electro-pneumatic assembly is composed of pneumatic valves (a) that control the connections between the compressed helium (P = 6-8 bar) line (b), the boiler (c) where the D2O is injected through the valve (d), and the outlet (e) through the carbon fiber stick (f). The system is completed by a pressure G, a thermometer and a heating resistive wire in the boiler (c), a trigger (h) and a connection box (i) used to interface the system with the electronic management device.
The DNP cryostat and the NMR spectrometer are connected by a transfer line, i.e., a PTFE tube of 2 mm inner diameter inside which the hyperpolarized solution is pushed by pressurized helium (P = 6-8 bar) when dissolution is triggered.
The dissolution sequence is composed of the following operations: in the first 300 msec, superheated D2O is pushed to the sample container in order to melt and dissolve the hyperpolarized frozen solution. Afterwards, the hyperpolarized solution is extracted from the cryostat by mean of pressurized (P = 6-8 bar) helium gas and pushed through the 2 mm inner diameter PTFE tube (Figure 3C-e) to the measurement site where the injection is performed with either of the procedures described in Step 6.2.1 or Step 6.2.2.
The second component of the dissolution DNP NMR setup is the NMR spectrometer. In the setup described herein, the NMR spectrometer operates at a field B0 = 11.7 Tesla. A 5 mm NMR probe is used to measure the hyperpolarized signal after the dissolution. The NMR spectrometer is operated through the NMR console, used for both solid-state and liquid-state NMR measurements, and the firm-provided software XWinNMR. A typical measurement is composed of a low flip angle hard pulse (either calibrated, for liquidstate or un-calibrated, for solid-state measurements) followed by signal acquisitions.
Measurements of the solid state thermal polarization signal and DNP-derived signal build-up are performed using the custom-made 13C coil at the site of the DNP polarizer (Figure 3Ab) coupled to the NMR spectrometer. In this particular situation the NMR spectrometer does not perform signal locking. When solid-state measurements are carried out, to avoid significant perturbations to the polarization, the time delay between acquisitions should be long enough, roughly longer than 0.5 TDNP.
The solid-state enhancement is defined as <img alt="Equation4" src="/files/ftp_upload/53548/53548equation4.jpg" width="100" /> where <img alt="Equation5" src="/files/ftp_upload/53548/53548equation5.jpg" width="31" /> is the hyperpolarized signal (obtained in Step 3.3) and <img alt="Equation6" src="/files/ftp_upload/53548/53548equation6.jpg" width="23" /> is the solid state signal (obtained at thermal equilibrium at pumped liquid helium temperature in Step 3.2) (Figure 4A). This parameter defines the maximal polarization available for NMR experiments, prior to unavoidable losses during the transfer of the hyperpolarized solution. The measurement is performed with a simple pulse-acquire sequence using an un-calibrated low flip angle pulse. Pulse calibration is commonly skipped for solidstate measurements.
An analogous procedure can be used to determine the hyperpolarized signal enhancement in the liquid-state. In this case, the sample placed in the spectrometer tube before the injection (Step 6.2) is composed of 500 &#181;l of D2O. After dissolution and injection, there are two important parameters to monitor. The first is the hyperpolarized enhancement at the NMR spectrometer site, <img alt="Equation7" src="/files/ftp_upload/53548/53548equation7.jpg" width="95" /> (Figure 4B), where <img alt="Equation8" src="/files/ftp_upload/53548/53548equation8.jpg" width="30" /> is the signal just after the injection of the hyperpolarized solution (obtained in Step 7.1) and <img alt="Equation9" src="/files/ftp_upload/53548/53548equation9.jpg" width="20" /> is the thermal polarization signal (obtained in Step 7.2). The second is the longitudinal relaxation time, T1 (Figure 4B, inset), associated with the substrate and each metabolic product (obtained by exponential fitting signals obtained in Step 7.1). These two parameters define the minimum substrate concentration necessary to obtain a sufficient signal-to-noise ratio (SNR) and the available time window for the measurement of the metabolic transformations. The ratio between solid-state polarization <img alt="Equation10" src="/files/ftp_upload/53548/53548equation10.jpg" width="30" /> and liquidstate polarization <img alt="Equation11" src="/files/ftp_upload/53548/53548equation11.jpg" width="29" /> gives an estimate of the polarization losses due to relaxation during the hyperpolarized solution transfer. A value <img alt="Equation12" src="/files/ftp_upload/53548/53548equation12.jpg" width="80" /> should be observed in absence of relaxation losses.

<table><tbody><tr><td>DNP polarizer</td><td>Vanderklink s.a.r.l (Switzerland)</td><td>///</td><td>Cryostat and electronic equipment for sample polarization</td></tr><tr><td>Vacuum system components</td><td>Edwards vacuum (France)</td><td>Various</td><td> &lt;p&gt;- turbomolecular pumping setup&lt;/p&gt; &lt;p&gt;- membrane pumping setup&lt;/p&gt; &lt;p&gt;- high capacity roots pumping system&lt;/p&gt; &lt;p&gt;- vacuum fittings and components&lt;/p&gt; </td></tr><tr><td>DNP 3.35T Magnet</td><td>Bruker (France)</td><td></td><td></td></tr><tr><td>500 MHz NMR Spectrometer</td><td>Bruker (France)</td><td></td><td></td></tr><tr><td>Origin 8.0</td><td>OriginLab (US)</td><td></td><td>Data analysis software</td></tr><tr><td>&lt;strong&gt;Chemicals&lt;/strong&gt;</td><td></td><td></td><td></td></tr><tr><td>SODIUM PYRUVATE-1-13C, 99 ATOM % 13C</td><td>Sigma Aldrich (France)</td><td>490709</td><td></td></tr><tr><td>ETHANOL-D6, ANHYDROUS, 99.5 ATOM % D</td><td>Sigma Aldrich (France)</td><td>186414</td><td></td></tr><tr><td>&amp;nbsp;4-Hydroxy-TEMPO 97%</td><td>Sigma Aldrich (France)</td><td>176141</td><td></td></tr><tr><td>Deuterium oxide</td><td>Sigma Aldrich (France)</td><td>151882</td><td></td></tr><tr><td>reduced nicotinamide adenine dinucleotide (NADH)</td><td>Sigma Aldrich (France)</td><td></td><td></td></tr><tr><td>ethylene-diaminetetraacetic acid (EDTA)</td><td>Sigma Aldrich (France)</td><td></td><td></td></tr><tr><td>dithiothreitol (DTT)</td><td>Sigma Aldrich (France)</td><td></td><td></td></tr><tr><td>phosphate buffer, pH&amp;nbsp;=&amp;nbsp;7.0</td><td>Sigma Aldrich (France)</td><td></td><td></td></tr><tr><td>LDH enzyme in&amp;nbsp;</td><td>Sigma Aldrich (France)</td><td>L-2500</td><td></td></tr><tr><td>bovine serum albumin, BSA</td><td>Sigma Aldrich (France)</td><td></td><td></td></tr></tbody></table>

dissolution dynamic nuclear polarization instrumentation for real-time enzymatic reaction rate measurements by nmr

The main limitation of NMR-based investigations is low sensitivity. This prompts for long acquisition times, thus preventing real-time NMR measurements of metabolic transformations. Hyperpolarization via dissolution DNP circumvents part of the sensitivity issues thanks to the large out-of-equilibrium nuclear magnetization stemming from the electron-to-nucleus spin polarization transfer. The high NMR signal obtained can be used to monitor chemical reactions in real time. The downside of hyperpolarized NMR resides in the limited time window available for signal acquisition, which is usually on the order of the nuclear spin longitudinal relaxation time constant, T1, or, in favorable cases, on the order of the relaxation time constant associated with the singlet-state of coupled nuclei, TLLS. Cellular uptake of endogenous molecules and metabolic rates can provide essential information on tumor development and drug response. Numerous previous hyperpolarized NMR studies have demonstrated the relevancy of pyruvate as a metabolic substrate for monitoring enzymatic activity in vivo. This work provides a detailed description of the experimental setup and methods required for the study of enzymatic reactions, in particular the pyruvate-to-lactate conversion rate in presence of lactate dehydrogenase (LDH), by hyperpolarized NMR.

NMR signal gains using dissolution DNP 
The DNP effect consists in the transfer of the high polarization of unpaired electron spins, typically from stable radical molecules, to NMR-active nuclei, under microwave irradiation of the sample. The most often-used free radicals are TAM(OXO63) and TEMPOL.4 Polarization procedures using TEMPOL may be optimized by &#39;cross-polarization&#39;.25
Optimizing the concentration of the stable radical in order to obtain the maximum nuclear polarization in the solid state is crucial to the success of the technique. The optimal TEMPOL concentration was found to be 33 mM in the experimental conditions of this study. This polarization of the chosen substrate is sufficient to follow its enzymatic conversion in real time.
The magnetic field of the polarizer installed at Paris Descartes is B0 = 3.35 T and the components of this system were described above (Figures 1-3). The cryostat design guarantees that the final sample position coincides with the magnet isocenter. The magnetic field of the polarizer was ramped and shimmed using the superconductive shim coils only, with the cryostat in place. The final proton line-width of a 1 x 0.5 x 0.5 cm water sample was 23 KHz. We assessed <img alt="Equation14" src="/files/ftp_upload/53548/53548equation14.jpg" width="29" /> and <img alt="Equation13" src="/files/ftp_upload/53548/53548equation13.jpg" width="29" /> for [113C]pyruvate. To do so, it is necessary first to determine the 13C DNP-enhanced signal <img alt="Equation5" src="/files/ftp_upload/53548/53548equation5.jpg" width="31" /> in the solid state at the polarizer site before the dissolution (Figure 4A). After dissolution, we measured the [1-13C] pyruvate hyperpolarized signal <img alt="Equation8" src="/files/ftp_upload/53548/53548equation8.jpg" width="30" /> and its decay at the spectrometer site. The liquid state signal was measured on a test dissolution using 500 &#956;l of D2O as sample in the NMR spectrometer. This allowed us to determine the solid-state DNP enhancement (Figure 4B, inset), the liquid-state NMR polarization level (Figure 4B) and the polarization losses during the transfer. The ratio between signals measured in Step 3.3 and Step 3.2 define the solid-state enhancement, <img alt="Equation14" src="/files/ftp_upload/53548/53548equation14.jpg" width="29" />. The ratio between the first signal measured in Step 7.1 and the signal from Step 7.2 defines the liquid-state hyperpolarized enhancement, <img alt="Equation13" src="/files/ftp_upload/53548/53548equation13.jpg" width="29" />.
Data from Step 3, summarized in Figure 4A and Figure 4A (inset), show that the technique allows to polarize 13C in [1-13C] pyruvate up to <img alt="Equation14" src="/files/ftp_upload/53548/53548equation14.jpg" width="29" /> = 22 &#177; 5, corresponding to a 13C polarization <img alt="Equation10" src="/files/ftp_upload/53548/53548equation10.jpg" width="30" /> = 1.5 &#177; 0.3%.
This polarization level is more than one thousand times the carbon thermal polarization in common MRS conditions (e.g., 11.74 T and 300 K). Data from Step 7, summarized in Figure 4B and Figure 4B (inset), allow determining the liquid-state 13C hyperpolarization of [1-13C]pyruvate, <img alt="Equation11" src="/files/ftp_upload/53548/53548equation11.jpg" width="29" /> = 1 &#177; 0.2%. The enhancement obtained in the solid state for pyruvate was sufficient for the purpose of the experiment, though higher enhancements have been demonstrated using different radicals.5 The time course data fit from Step 7.1 gives a measure of the relaxation time constant. The pyruvate longitudinal relaxation time in the mixture composed of 500 &#956;l DNP enhanced solution and 500 &#956;l D2O, was T1 = 75 &#177; 5 sec after rf correction (see equation (3)).
Enzymatic activity and metabolic measurements 
Dissolution DNP NMR detection of 13C-labeled substrate (A) can be used to follow in real time enzymatic conversion dynamics and observe the formation of product (B):
<img alt="Equation1" src="/files/ftp_upload/53548/53548equation1.jpg" />
Immediately after the injection of hyperpolarized substrate (A), the signal of product (B) is null. Then, the enzymatic conversion (1) starts to produce (B). The magnetization of the 13C nuclei is not affected by the different chemical shifts and the chemical change of the molecules. Nevertheless, the new environment may lead to different longitudinal relaxation rates for the 13C in B. The product signal time course can be qualitatively separated in three steps: in the beginning, the enzymatic conversion transforming A into B produces an increase in B signal; after a certain time, dependent on the experimental conditions, the magnetization losses due to relaxation, balance this increase and the signal of B reaches a maximum; finally, at longer times, the signal of B decays due to longitudinal relaxation. In the hypothesis of enzyme saturation, neglecting back conversion and taking into account magnetic relaxation, the magnetization of the two molecular species (A and B) during the enzymatic conversion can be described by a coupled differential equation system:22
<img alt="Equation2" src="/files/ftp_upload/53548/53548equation2.jpg" />
where M(A,B)(t) are magnetizations of molecular species A and B, respectively, keff is the effective conversion rate constant for signal transfer by the enzymatic reaction and R(A,B) are the apparent longitudinal relaxation rate constants of observed nuclei in the molecular species A and B, respectively. R(A,B) account for both the pure longitudinal magnetization relaxation and the effect of rf pulsing:
<img alt="Equation3" src="/files/ftp_upload/53548/53548equation3.jpg" />
where T1,(A,B) is the longitudinal relaxation time constant of the nucleus in the local molecular environment of molecular species A and B, respectively. &#952; and &#964; are the rf flip angle and the delay between two signal acquisitions, respectively.
In this study, substrate A and product B were [1-13C]pyruvate and [1-13C]lactate, respectively, and the aim was to measure [1-13C]lactate production by LDH under conditions where no (isotopically unlabelled) lactate was present in the solution at the beginning of the experiment. The measurement consists in a series of 13C spectra recorded with a simple pulseacquire sequence at T = 21 &#176;C. A calibrated 10&#176; flip angle pulse was used for the sequential excitations (Step 9). The delay between two successive pulses was &#964; = 1.5 sec. The NMR acquisition sequence was started a few tens of seconds before the hyperpolarized solution injection. The pyruvate substrate concentration in the sample tube after the injection was 25-35 mM. In Step 10 the lactate to pyruvate conversion speed at an LDH concentration of 10-3 U/ml was measured. The recorded signal from lactate and pyruvate fit well the model in equation (2) (dotted line in Figure 5) and yield keff = 0.9 &#177; 0.1 x 10-3 sec-1 (Figure 5). This value agrees with the initial reaction rate determined by the ratio [Lac]/[Pyr] at time 0 sec (Figure 5, inset).
<img alt="Figure 1" src="/files/ftp_upload/53548/53548fig1.jpg" /> 
Figure 1.&#160;Schematics of the experimental apparatus. The polarizer (left) consists of a microwave cavity (c) located inside a cryostat (d) placed into a wide-bore 3.35 T superconducting magnet. A custom-made NMR coil (b) surrounding the sample (a) is used for monitoring the nuclear spin polarization in situ. The helium bath temperature is maintained at 1.12 &#177; 0.03 K while the sample is irradiated at the microwave frequency &#957;mw = 94 GHz. The system allows for NMR measurement to be performed on the solid-state sample during the polarization. The polarized sample is dissolved in superheated water and pushed with compressed helium gas through the transfer line into the sample tube previously placed inside an adjacent NMR spectrometer (right). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53548/53548fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" src="/files/ftp_upload/53548/53548fig2.jpg" /> 
Figure 2.&#160;Cryostat and vacuum system schematics. (A) cryostat insulation dewar; (B) cryostat main insert; (C) vacuum system connections; (D) screenshot of management software interface with buttons used to perform specific operations described in Step 2 and Step 5 of the protocol section. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53548/53548fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" src="/files/ftp_upload/53548/53548fig3.jpg" /> 
Figure 3.&#160;Sample handling and dissolution. (A) sample handling inserts; (B) dissolution insert; (C) detail of electro-pneumatic connections of dissolution insert. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53548/53548fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a> 
&#160;
<img alt="Figure 4" src="/files/ftp_upload/53548/53548fig4.jpg" /> 
Figure 4.&#160;Solid-state polarization buildup and hyperpolarized signal decay. Dissolution DNP signals. (A) solid-state NMR polarization build-up signal of a 1.12 M sodium [1-13C]pyruvate solution during a DNP polarization (crosses, fitted with an exponential function S(t) = A x exp(-t/Tb) + B of time constant Tb = 270 sec) and relaxation (circles, S(t) = A&#183;exp(t/Tb) + B, Tss1 = 840 sec); (A, inset) comparison between DNPenhanced and thermally-polarized (scaled up 10 times) magnetization signals in the solid state (&#949;ss = 22&#160;&#177; 5, corresponding to a solid-state polarization PSS = 1.5 &#177; 0.3%); (B) comparison between the first spectrum recorded after dissolution and the averaged spectrum (scaled up 100 times) obtained from the thermally polarized 13C spins at RT using 1,024 transients (&#949; = 1,000&#160;&#177; 200). The dissolution process took 3.3 sec and the automatic injection about 2 sec with an estimated signal loss of 40%. For the experiments performed transferring the sample by manual injection, additional losses due to the longer injection delay were estimated to 30%; (B, inset) hyperpolarized signal decay of pyruvate after dissolution in absence of LDH (T1 = 75&#160;&#177; 5 sec). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53548/53548fig4large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" src="/files/ftp_upload/53548/53548fig5.jpg" /> 
Figure 5.&#160;LDH activity and cancer cell metabolism results. Build-up of [1-13C]lactate signal due to enzymatic conversion at a LDH concentration of 10-3 U/ml followed by signal decay due to longitudinal relaxation of 13C magnetization. The red line shows the fit with the model described in equation (2) comprising the effects of relaxation and enzymatic conversion. (Inset) ratio between [1-13C]lactate and [1-13C]pyruvate concentration with an extrapolation of the reaction speed at time t = 0 (red line). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53548/53548fig5large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Dissolution Dynamic Nuclear Polarization Instrumentation for Real-time Enzymatic Reaction Rate Measurements by NMR at JoVE.com

Dissolution Dynamic Nuclear Polarization Instrumentation for Real-time Enzymatic Reaction Rate Measurements by NMR

The sensitivity enhancement provided by dissolution dynamic nuclear polarization (DNP) enables following metabolic processes in real time by NMR and MRI. The characteristics and performances of a dedicated dissolution DNP setup designed for study enzymatic reactions are discussed.

The main limitation of NMR-based investigations is low sensitivity. This prompts for long acquisition times, thus preventing real-time NMR measurements of ...

dissolution-dynamic-nuclear-polarization-instrumentation-for-real

Nanyang Technological University

Research

Education

JoVE Core

JoVE Journal

Analytical Chemistry

Chemistry

Unit 1

Chemical Equilibria

SCIENTISTS IN ACTION

10.6K Views.  Université Paris Descartes. The sensitivity enhancement provided by dissolution dynamic nuclear polarization (DNP) enables following metabolic processes in real time by NMR and MRI. The characteristics and performances of a dedicated dissolution DNP setup designed for study enzymatic reactions are discussed.

Video: Dissolution Dynamic Nuclear Polarization Instrumentation for Real-time Enzymatic Reaction Rate Measurements by NMR

Hyperpolarized 13C Metabolic Magnetic Resonance Spectroscopy and Imaging

In the past decades, new methods for tumor staging, restaging, treatment response monitoring, and recurrence detection of a variety of cancers have emerged in conjunction with the state-of-the-art positron emission tomography with 18F-fluorodeoxyglucose ([18F]-FDG PET). 13C magnetic resonance spectroscopic imaging (13CMRSI) is a minimally invasive imaging method that enables the monitoring of metabolism in vivo and in real time. As with any other method based on 13C nuclear magnetic resonance (NMR), it faces the challenge of low thermal polarization and a subsequent low signal-to-noise ratio due to the relatively low gyromagnetic ratio of 13C and its low natural abundance in biological samples. By overcoming these limitations, dynamic nuclear polarization (DNP) with subsequent sample dissolution has recently enabled commonly used NMR and magnetic resonance imaging (MRI) systems to measure, study, and image key metabolic pathways in various biological systems. A particularly interesting and promising molecule used in 13CMRSI is [1-13C]pyruvate, which, in the last ten years, has been widely used for in vitro, preclinical, and, more recently, clinical studies to investigate the cellular energy metabolism in cancer and other diseases. In this article, we outline the technique of dissolution DNP using a 3.35 T preclinical DNP hyperpolarizer and demonstrate its usage in in vitro studies. A similar protocol for hyperpolarization may be applied for the most part in in vivo studies as well. To do so, we used lactate dehydrogenase (LDH) and catalyzed the metabolic reaction of [1-13C]pyruvate to [1-13C]lactate in a prostate carcinoma cell line, PC3, in vitro using 13CMRSI.

Hyperpolarized 13C Metabolic Magnetic Resonance Spectroscopy and Imaging

Dynamic nuclear polarization with subsequent sample dissolution has enabled real-time studies of metabolism in biological systems. Hyperpolarized [1-13C]pyruvate was used to study lactate dehydrogenase activity in a prostate carcinoma cell line in vitro.

In the past decades, new methods for tumor staging, restaging, treatment response monitoring, and recurrence detection of a variety of cancers have ...

Cancer Research

Nuclear Magnetic Resonance Spectroscopy for the Identification of Multiple Phosphorylations of Intrinsically Disordered Proteins

Aggregates of the neuronal Tau protein are found inside neurons of Alzheimer's disease patients. Development of the disease is accompanied by increased, abnormal phosphorylation of Tau. In the course of the molecular investigation of Tau functions and dysfunctions in the disease, nuclear magnetic resonance (NMR) spectroscopy is used to identify the multiple phosphorylations of Tau. We present here detailed protocols of recombinant production of Tau in bacteria, with isotopic enrichment for NMR studies. Purification steps that take advantage of Tau's heat stability and high isoelectric point are described. The protocol for in vitro phosphorylation of Tau by recombinant activated ERK2 allows for generating multiple phosphorylations. The protein sample is ready for data acquisition at the issue of these steps. The parameter setup to start recording on the spectrometer is considered next. Finally, the strategy to identify phosphorylation sites of modified Tau, based on NMR data, is explained. The benefit of this methodology compared to other techniques used to identify phosphorylation sites, such as immuno-detection or mass spectrometry (MS), is discussed.

We describe here a method to identify multiple phosphorylations of an intrinsically disordered protein by Nuclear Magnetic Resonance Spectroscopy (NMR), using Tau protein as a case study. Recombinant Tau is isotopically enriched and modified in vitro by a kinase prior to data acquisition and analysis.

Aggregates of the neuronal Tau protein are found inside neurons of Alzheimer's disease patients. Development of the disease is accompanied by increased, ...

Biochemistry

Use of a Multi-compartment Dynamic Single Enzyme Phantom for Studies of Hyperpolarized Magnetic Resonance Agents

Imaging of hyperpolarized substrates by magnetic resonance shows great clinical promise for assessment of critical biochemical processes in real time. Due to fundamental constraints imposed by the hyperpolarized state, exotic imaging and reconstruction techniques are commonly used. A practical system for characterization of dynamic, multi-spectral imaging methods is critically needed. Such a system must reproducibly recapitulate the relevant chemical dynamics of normal and pathological tissues. The most widely utilized substrate to date is hyperpolarized [1-13C]-pyruvate for assessment of cancer metabolism. We describe an enzyme-based phantom system that mediates the conversion of pyruvate to lactate. The reaction is initiated by injection of the hyperpolarized agent into multiple chambers within the phantom, each of which contains varying concentrations of reagents that control the reaction rate. Multiple compartments are necessary to ensure that imaging sequences faithfully capture the spatial and metabolic heterogeneity of tissue. This system will aid the development and validation of advanced imaging strategies by providing chemical dynamics that are not available from conventional phantoms, as well as control and reproducibility that is not possible in vivo.

A multi-compartment dynamic phantom is used to simulate some biology of interest for metabolic studies using hyperpolarized magnet resonance agents.

Imaging of hyperpolarized substrates by magnetic resonance shows great clinical promise for assessment of critical biochemical processes in real time. Due ...

Engineering

Preparation of Fungal and Plant Materials for Structural Elucidation Using Dynamic Nuclear Polarization Solid-State NMR

This protocol shows how uniformly 13C, 15N-labeled fungal materials can be produced and how these soft materials should be proceeded for solid-state NMR and sensitivity-enhanced DNP experiments. The sample processing procedure of plant biomass is also detailed. This method allows the measurement of a series of 1D and 2D 13C-13C/15N correlations spectra, which enables high-resolution structural elucidation of complex biomaterials in their native state, with minimal perturbation. The isotope-labeling can be examined by quantifying the intensity in 1D spectra and the polarization transfer efficiency in 2D correlation spectra. The success of dynamic nuclear polarization (DNP) sample preparation can be evaluated by the sensitivity enhancement factor. Further experiments examining the structural aspects of the polysaccharides and proteins will lead to a model of the three-dimensional architecture. These methods can be modified and adapted to investigate a wide range of carbohydrate-rich materials, including the natural cell walls of plants, fungi, algae and bacteria, as well as synthesized or designed carbohydrate polymers and their complex with other molecules.

A protocol for preparing 13C,15N-labeled fungal and plant samples for multidimensional solid-state NMR spectroscopy and dynamic nuclear polarization (DNP) investigations is presented.

This protocol shows how uniformly 13C, 15N-labeled fungal materials can be produced and how these soft materials should be proceeded for solid-state NMR ...

15N CPMG Relaxation Dispersion for the Investigation of Protein Conformational Dynamics on the &#181;s-ms Timescale

Protein conformational dynamics play fundamental roles in regulation of enzymatic catalysis, ligand binding, allostery, and signaling, which are important biological processes. Understanding how the balance between structure and dynamics governs biological function is a new frontier in modern structural biology and has ignited several technical and methodological developments. Among these, CPMG relaxation dispersion solution NMR methods provide unique, atomic-resolution information on the structure, kinetics, and thermodynamics of protein conformational equilibria occurring on the &#181;s-ms timescale. Here, the study presents detailed protocols for acquisition and analysis of a&#160;15N relaxation dispersion experiment. As an example, the pipeline for the analysis of the &#181;s-ms dynamics in the C-terminal domain of bacteria Enzyme I is shown.

15N CPMG Relaxation Dispersion for the Investigation of Protein Conformational Dynamics on the  &#181;s-ms Timescale

Here, a detailed description of the protocol implemented in the laboratory for acquisition and analysis of 15N relaxation dispersion profiles by solution NMR spectroscopy is provided.

Protein conformational dynamics play fundamental roles in regulation of enzymatic catalysis, ligand binding, allostery, and signaling, which are important ...

Rapid Scan Electron Paramagnetic Resonance Opens New Avenues for Imaging Physiologically Important Parameters In Vivo

We demonstrate a superior method of 2D spectral-spatial imaging of stable radical reporter molecules at 250 MHz using rapid-scan electron-paramagnetic-resonance (RS-EPR), which can provide quantitative information under in vivo conditions on oxygen concentration, pH, redox status and concentration of signaling molecules (i.e., OH&#8226;, NO&#8226;). The RS-EPR technique has a higher sensitivity, improved spatial resolution (1 mm), and shorter acquisition time in comparison to the standard continuous wave (CW) technique. A variety of phantom configurations have been tested, with spatial resolution varying from 1 to 6 mm, and spectral width of the reporter molecules ranging from 16 &#181;T (160 mG) to 5 mT (50 G). A cross-loop bimodal resonator decouples excitation and detection, reducing the noise, while the rapid scan effect allows more power to be input to the spin system before saturation, increasing the EPR signal. This leads to a substantially higher signal-to-noise ratio than in conventional CW EPR experiments.

Rapid Scan Electron Paramagnetic Resonance Opens New Avenues for Imaging Physiologically Important Parameters In Vivo

A new electron paramagnetic resonance (EPR) method, rapid scan EPR (RS-EPR), is demonstrated for 2D spectral spatial imaging which is superior to the traditional continuous wave (CW) technique and opens new venues for in vivo imaging. Results are demonstrated at 250 MHz, but the technique is applicable at any frequency.

We demonstrate a superior method of 2D spectral-spatial imaging of stable radical reporter molecules at 250 MHz using rapid-scan ...

Bioengineering

High-Resolution Studies of Proteins in Natural Membranes by Solid-State NMR

Membrane proteins are vital for cell function and thus represent important drug targets. Solid-state Nuclear Magnetic Resonance (ssNMR) spectroscopy offers a unique access to probe the structure and dynamics of such proteins in biological membranes of increasing complexity. Here, we present modern solid-state NMR spectroscopy as a tool to study structure and dynamics of proteins in natural lipid membranes and at atomic scale. Such spectroscopic studies profit from the use of high-sensitivity ssNMR methods, i.e., proton-(1H)-detected ssNMR and DNP (Dynamic Nuclear Polarization) supported ssNMR. Using bacterial outer membrane beta-barrel protein BamA and the ion channel KcsA, we present methods to prepare isotope-labeled membrane proteins and to derive structural and motional information by ssNMR.

This work details robust basic routines on how to prepare isotope-labeled membrane protein samples and analyze them at high-resolution with modern solid-state NMR spectroscopy methods.

Membrane proteins are vital for cell function and thus represent important drug targets. Solid-state Nuclear Magnetic Resonance (ssNMR) spectroscopy ...

Measuring the Spin-Lattice Relaxation Magnetic Field Dependence of Hyperpolarized [1-13C]pyruvate

The fundamental limit to in vivo imaging applications of hyperpolarized 13C-enriched compounds is their finite spin-lattice relaxation times. Various factors affect the relaxation rates, such as buffer composition, solution pH, temperature, and magnetic field. In this last regard, the spin-lattice relaxation time can be measured at clinical field strengths, but at lower fields, where these compounds are dispensed from the polarizer and transported to the MRI, the relaxation is even faster and difficult to measure. To have a better understanding of the amount of magnetization lost during transport, we used fast field-cycling relaxometry, with magnetic resonance detection of 13C nuclei at ~0.75 T, to measure the nuclear magnetic resonance dispersion of the spin-lattice relaxation time of hyperpolarized [1-13C]pyruvate. Dissolution dynamic nuclear polarization was used to produce hyperpolarized samples of pyruvate at a concentration of 80 mmol/L and physiological pH (~7.8). These solutions were rapidly transferred to a fast field-cycling relaxometer so that relaxation of the sample magnetization could be measured as a function of time using a calibrated small flip angle (3&#176;-5&#176;). To map the T1 dispersion of the C-1 of pyruvate, we recorded data for different relaxation fields ranging between 0.237 mT and 0.705 T. With this information, we determined an empirical equation to estimate the spin-lattice relaxation of the hyperpolarized substrate within the mentioned range of magnetic fields. These results can be used to predict the amount of magnetization lost during transport and to improve experimental designs to minimize signal loss.

Measuring the Spin-Lattice Relaxation Magnetic Field Dependence of Hyperpolarized [1-13C]pyruvate

We present a protocol to measure the magnetic field dependence of the spin-lattice relaxation time of 13C-enriched compounds, hyperpolarized by means of dynamic nuclear polarization, using fast field-cycled relaxometry. Specifically, we have demonstrated this with [1-13C]pyruvate, but the protocol could be extended to other hyperpolarized substrates.

The fundamental limit to in vivo imaging applications of hyperpolarized 13C-enriched compounds is their finite spin-lattice relaxation times. Various ...

Protocol for NMR 15N Relaxation and hetNOE Experiments in Protein Dynamics Study

NMR 15N Relaxation Experiments for the Investigation of Picosecond to Nanoseconds Structural Dynamics of Proteins

Nuclear magnetic resonance (NMR) spectroscopy allows studying proteins in solution and under physiological temperatures. Frequently, either the amide groups of the protein backbone or the methyl groups in side chains are used as reporters of structural dynamics in proteins. A structural dynamics study of the protein backbone of globular proteins on 15N labeled and fully protonated samples usually works well for proteins with a molecular weight of up to 50 kDa. When side chain deuteration in combination with transverse relaxation optimized spectroscopy (TROSY) is applied, this limit can be extended up to 200 kDa for globular proteins and up to 1 MDa when the focus is on the side chains. When intrinsically disordered proteins (IDPs) or proteins with intrinsically disordered regions (IDRs) are investigated, these weight limitations do not apply but can go well beyond. The reason is that IDPs or IDRs, characterized by high internal flexibility, are frequently dynamically decoupled. Various NMR methods offer atomic-resolution insights into structural protein dynamics across a wide range of time scales, from picoseconds up to hours. Standard 15N relaxation measurements overview a protein&#39;s internal flexibility and characterize the protein backbone dynamics experienced on the fast pico- to nanosecond timescale. This article presents a hands-on protocol for setting up and recording NMR 15N R1, R2, and heteronuclear Overhauser effect (hetNOE) experiments. We show exemplary data and explain how to interpret them simply qualitatively before any more sophisticated analysis.

Author Spotlight: Exploring Intrinsically Disordered Protein Dynamics Through NMR Relaxation Experiments

Nuclear magnetic resonance (NMR) spectroscopy can characterize structural protein dynamics in a residue-specific manner. We provide a hands-on protocol for recording NMR 15N R1 and R2 relaxation and {1H}-15N heteronuclear Overhauser effect (hetNOE) experiments, sensitive to the picoseconds to nanoseconds timescale.

Nuclear magnetic resonance (NMR) spectroscopy allows studying proteins in solution and under physiological temperatures. Frequently, either the amide ...

Cryogenic Sample Loading into a Magic Angle Spinning Nuclear Magnetic Resonance Spectrometer that Preserves Cellular Viability

Dynamic nuclear polarization (DNP) can dramatically increase the sensitivity of magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy. These sensitivity gains increase as temperatures decrease and are large enough to enable the study of molecules at very low concentrations at the operating temperatures (~100 K) of most commercial DNP-equipped NMR spectrometers. This leads to the possibility of in-cell structural biology on cryopreserved cells for macromolecules at their endogenous levels in their native environments. However, the freezing rates required for cellular cryopreservation are exceeded during typical sample handling for DNP MAS NMR and this results in loss of cellular integrity and viability. This article describes a detailed protocol for the preparation and cryogenic transfer of a frozen sample of mammalian cells into a MAS NMR spectrometer.

Presented here is a protocol for cryogenic transfer of frozen samples into the dynamic nuclear polarization (DNP) magic angle spinning (MAS) nuclear magnetic resonance (NMR) probe. The protocol includes directions for rotor storage prior to the experiment and directions for viability measurements before and after the experiment.

Dynamic nuclear polarization (DNP) can dramatically increase the sensitivity of magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy. ...

Dissolution Dynamic Nuclear Polarization Instrumentation for Real-time Enzymatic Reaction Rate Measurements by NMR

Summary

Explore More Videos

Chapters in this video

Hyperpolarized ¹³C Metabolic Magnetic Resonance Spectroscopy and Imaging

Nuclear Magnetic Resonance Spectroscopy for the Identification of Multiple Phosphorylations of Intrinsically Disordered Proteins

Use of a Multi-compartment Dynamic Single Enzyme Phantom for Studies of Hyperpolarized Magnetic Resonance Agents

Preparation of Fungal and Plant Materials for Structural Elucidation Using Dynamic Nuclear Polarization Solid-State NMR

¹⁵N CPMG Relaxation Dispersion for the Investigation of Protein Conformational Dynamics on the µs-ms Timescale

Rapid Scan Electron Paramagnetic Resonance Opens New Avenues for Imaging Physiologically Important Parameters In Vivo

High-Resolution Studies of Proteins in Natural Membranes by Solid-State NMR

Measuring the Spin-Lattice Relaxation Magnetic Field Dependence of Hyperpolarized [1-¹³C]pyruvate

NMR ¹⁵N Relaxation Experiments for the Investigation of Picosecond to Nanoseconds Structural Dynamics of Proteins

Cryogenic Sample Loading into a Magic Angle Spinning Nuclear Magnetic Resonance Spectrometer that Preserves Cellular Viability