The authors have no acknowledgements.

1. Pre-test Preparation
<ol>
	<li>Design and fabricate the test fixture. Design the fixture to replicate realistic boundary conditions by choosing bolt locations to match the mounting locations of the blade. Choose steel for the fixture to minimize the contribution from the fixture to the dynamic response of the test specimen.
	<ol>
		<li>Bolt the blade to the custom t-bracket.</li>
		<li>Clamp the fixture to a steel table.</li>
	</ol>
	</li>
	<li>Identify and mark grid of impact locations.
	<ol>
		<li>Choose 30 points that span the entire blade.</li>
		<li>Mark points with a marker or wax pen and number for reference. Measure point spacing using a tape measure for later use in visual representation of results.</li>
	</ol>
	</li>
	<li>Select and calibrate accelerometers.
	<ol>
		<li>Choose single axis, 10 mV/g accelerometers. Be sure to choose accelerometers with the appropriate sensitivity in order to avoid overloading the sensor and to achieve good signal-to-noise ratios. Also, be sure the frequency range of the sensors is sufficient to capture the frequency range of interest for the test specimen.</li>
		<li>Calibrate each sensor.
		<ol>
			<li>Attach the sensor to a hand-held shaker whose output is a single-frequency force with a magnitude of 9.81 m/sec2 rms (i.e., 1 g).</li>
			<li>Measure the response for 2 sec.</li>
			<li>Determine the rms amplitude of the response from the software readout.</li>
			<li>Multiply the rms amplitude by 1,000 to determine the calibration factor for the accelerometer in units of mV/g.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Select hammer and hammer tip.
	<ol>
		<li>Choose an impact hammer with a sensitivity of 11.2 mV/N. Be sure to select a hammer that sufficiently excites the test specimen in both amplitude and frequency range.</li>
		<li>Choose a nylon tip. Be sure to select a hammer tip that sufficiently excites the test specimen in both amplitude and frequency range.</li>
		<li>Connect the hammer to the data acquisition system with a BNC cable.</li>
	</ol>
	</li>
	<li>Identify sensor locations and attach sensors (Figure 4).
	<ol>
		<li>Choose locations at points m and n on either side of the damage location.</li>
		<li>Mount a third accelerometer at location k. Data from this sensor will be used to validate the results of the embedded sensitivity function analysis.</li>
		<li>Attach accelerometers using super glue. Allow the super glue to set completely before conducting the impact testing.</li>
	</ol>
	</li>
	<li>Select test parameters in the data acquisition GUI.
	<ol>
		<li>Enable double hit detection.</li>
		<li>Set the sampling frequency to 25,600 Hz. The usable frequency range is, therefore, 12,800 Hz.</li>
		<li>Set the sample time to 1 sec.</li>
		<li>Select the hammer channel as the trigger channel. Set the trigger level to 10 EU.</li>
		<li>Set the pre-trigger length to 5% of the total sample time. The pre-trigger data is data collected before the data acquisition is started that has been stored in a buffer. It is important to retrieve and save this data so that the entire impact event is captured.</li>
		<li>Select the H1 FRF estimator. This estimator assumes that there is noise on the response channels and no noise on the force channel. 
		Note: Do not window data during acquisition. Windows can be applied in post-processing, if necessary.</li>
		<li>Enter accelerometer and hammer information, including calibration factors and identification notes.</li>
		<li>Save settings for record keeping and for use in future tests.</li>
	</ol>
	</li>
</ol>
2. Impact Testing on the Healthy Blade
<ol>
	<li>Impact point 1 with the hammer. When the amplitude of the impact force exceeds the chosen trigger level, the data acquisition system will be triggered and data, including the selected amount of pre-trigger data, will begin recording.
	<ol>
		<li>During data acquisition, monitor channels to avoid channel clipping and double impacts by observing the time histories displayed in the data acquisition software.</li>
		<li>During data acquisition, monitor the coherence for each accelerometer channel to evaluate the quality of the acquired data by observing the coherence plot in the data acquisition software.</li>
	</ol>
	</li>
	<li>Repeat step 2.1 four more times at point 1.
	<ol>
		<li>Use consistent impact amplitudes for all impacts.</li>
	</ol>
	</li>
	<li>Repeat steps 2.1 and 2.2 for all points.</li>
</ol>
3. Impact Testing on the Damaged Blade
<ol>
	<li>Repeat section 2 on the damaged blade in order to collect data for validating the embedded sensitivity function results. Except for the change in the test specimen, all test parameters are kept the same.</li>
</ol>

<ol>
	<li>Singh, N., Joshi, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optimization+of+location+and+number+of+sensors+for+structural+health+monitoring+using+genetic+algorithm.">Optimization of location and number of sensors for structural health monitoring using genetic algorithm.</a> Mater Forum. 33, 359-367 (2009).</li><li>Gao, H., Rose, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultrasonic+sensor+placement+optimization+in+structural+health+monitoring+using+evolutionary+strategy.">Ultrasonic sensor placement optimization in structural health monitoring using evolutionary strategy.</a> Review Of Qnde. 25, 1687-1693 (2006).</li><li>Raich, A. M., Liszkai, T. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multi-objective+optimization+of+sensor+and+excitation+layouts+for+frequency+response+function-based+structural+damage+identification.">Multi-objective optimization of sensor and excitation layouts for frequency response function-based structural damage identification.</a> Comput-Aided Civinfrastructure Eng. 27 (2), 95-117 (2012).</li><li>Worden, K., Burrows, A. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optimal+sensor+placement+for+fault+detection.">Optimal sensor placement for fault detection.</a> Eng Struct. 23 (8), 885-901 (2001).</li><li>Flynn, E. B., Todd, M. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Bayesian+approach+to+optimal+sensor+placement+for+structural+health+monitoring+with+application+to+active+sensing.">A Bayesian approach to optimal sensor placement for structural health monitoring with application to active sensing.</a> Mech Syst Signal Pr. 24 (4), 891-903 (2010).</li><li>Markmiller, J., Chang, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sensor+network+optimization+for+a+passive+sensing+impact+detection+technique.">Sensor network optimization for a passive sensing impact detection technique.</a> Struct Health Monit. 9 (1), 25-39 (2010).</li><li>Yang, C., Adams, D., Yoo, S., Kim, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+embedded+sensitivity+approach+for+diagnosing+system-level+noise+and+vibration+problems.">An embedded sensitivity approach for diagnosing system-level noise and vibration problems.</a> J. Sound Vibration. 269 (3), 1063-1081 (2004).</li><li>Yang, C., Adams, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Predicting+changes+in+vibration+behavior+using+first-+and+second-order+iterative+embedded+sensitivity+functions.">Predicting changes in vibration behavior using first- and second-order iterative embedded sensitivity functions.</a> J. Sound Vibration. 323 (1), 173-193 (2009).</li><li>Yang, C., Adams, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Damage+Identification+Technique+based+on+Embedded+Sensitivity+Analysis+and+Optimization+Processes.">A Damage Identification Technique based on Embedded Sensitivity Analysis and Optimization Processes.</a> J. Sound Vibration. 333 (14), 3109-3119 (2013).</li><li>Rocklin, G. T., Crowley, J., Vold, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+comparison+of+the+H1,+H2,+and+Hv+frequency+response+functions.">A comparison of the H1, H2, and Hv frequency response functions.</a> Proc. Of IMAC III. 1, 272-278 (1985).</li><li>Meyer, J., Adams, D., Silvers, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Embedded+Sensitivity+Functions+for+improving+the+effectiveness+of+vibro-acoustic+modulation+and+damage+detection+on+wind+turbine+blades.">Embedded Sensitivity Functions for improving the effectiveness of vibro-acoustic modulation and damage detection on wind turbine blades.</a> , (2014).</li><li>Guratzsch, R., Mahadevan, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Structural+health+monitoring+sensor+placement+optimization+under+uncertainty.">Structural health monitoring sensor placement optimization under uncertainty.</a> AIAA J. 48 (7), 1281-1289 (2010).</li></ol>

The authors have nothing to disclose.

Test fixtures should be designed to replicate realistic boundary conditions so that results will be applicable under operating conditions. The selection of the number of impact points used for testing is a trade-off between having sufficient spatial resolution and the testing time. Select the hammer based on the size of the test specimen and the frequency range of interest. In general, the smaller the hammer, the broader the frequency range excited. However, smaller hammers typically produce lower amplitude forces. Impact hammers are instrumented with a force gauge to measure the time history of the impact. The type of hammer tip also affects the frequency range of excitation. The harder the tip, the broader the frequency band of excitation. Super glue is chosen over wax, for example, to minimize the attenuation of the response by the mounting material.
In the data acquisition software, enable double hit detection in order to automatically indicate when a double impact has occurred. Single impacts are desired because they produce a broader, more repeatable force spectrum. When the amplitude of the force rises above the selected trigger level, the data acquisition is started. Time data is acquired by the data acquisition software. During acquisition data should be monitored to ensure data quality. Channel clipping, which occurs when the response measured by the sensor exceeds the allowable voltage range, should be avoided. Coherence is an excellent metric to use to judge data quality. In general, coherence should be near one for all frequencies within the frequency range excited by the impact. Dips in coherence are expected near anti-resonance frequencies of the test specimen because the signal to noise ratio is low and the noise is uncorrelated with the input. Once quality data is acquired, the time histories are converted into the frequency domain via the Fast Fourier Transform (FFT), and the average FRF is estimated using the H1 estimator 10.
To determine the ESF from the FRFs measured during testing, equation 1 can be used in one of two ways. First, the direct approach can be used, which requires measurements for Hjm, Hjn, Hkm, and Hkn. These FRFs would be determined by placing a sensor at location k and roving a sensor to each potential sensor location j. Impacts would be applied at the two locations that span the damage location. To make data collection more efficient, the principal of reciprocity can be used to reverse the input and measurement locations. Using this approach, Hmj, Hnj, Hmk, and Hnk are determined. Now, instead of having to move the sensors for each different measurement, the sensors stay stationary and the impact location is roved. Once the ESFs are calculated for each location, their amplitudes are compared to determine which location j is most sensitive to damage between locations m and n. Note that a single damage location is assumed in this work.
The results of the ESF analysis can now be used in an FRF-based structural health monitoring scheme. In 11, it was demonstrated that the sensor locations identified by ESFs as being most sensitive to damage were more effective in identifying the presence of damage to a wind turbine blade.
Other methods to predict locations at which a structure&#39;s FRF will be sensitive to damage typically rely on analytical modeling of the structure3, 6, 12. FRF data is simulated using different combinations of input and measurement locations. However, the results of these methods rely on the development of a reliable and accurate model, which requires detailed knowledge of material properties and the geometry of the structure. Because ESFs can be calculated from experimentally measured data on the healthy structure, the identification of material properties is not required and the geometry of the structure does not need to be determined.
One potential limitation of the technique is that it requires a priori knowledge of where the damage is going to occur. In many applications, this requirement is not limiting because due to stress analyses and prior experience, the damage location can be foreseen. In applications where the damage location is unknown, multiple data sets can be acquired, each time assuming a different damage location. Within the data acquisition protocol, many best practices were identified that not only apply to data acquisition for ESFs, but also apply generally to modal impact testing. Being able to judge the quality of the data being acquired improves with experience, but knowing fundamentals including determining force roll-off and evaluating coherence will enable even those new to modal impact testing to acquire high-quality data.

Many structural health monitoring techniques rely on changes in measured frequency response functions (FRFs) to detect damage within a structure. However, few of these methods address how to determine sensor placements and/or input force locations that will maximize the effectiveness of the method to detect damage. Embedded sensitivity functions (ESFs) can be used to determine the sensitivity of an FRF to a local change in a structure&#39;s material properties. Therefore, because damage typically results in a local change in stiffness, damping, or mass of the structure, ESFs provide a method for determining the best sensor and force locations for FRF-based health monitoring techniques.
The purpose of this video and manuscript is to detail the data acquisition process and best practices for determining ESFs for a structure. The process includes determining various FRFs from modal impact testing, which is performed by exciting a structure with a modal impact hammer and measuring its response with accelerometers. In this work, the structure being tested is a 1.2 m residential-scale wind turbine blade. The goal of the testing and analysis is to identify sensor locations which are most sensitive to damage to the blade. These sensor locations could then be used in a structural health monitoring scheme to monitor the blade for damage.
Besides the use of ESFs to determine the most effective sensor locations to use in a structural health monitoring scheme, several optimal sensor placement algorithms can also be found demonstrated in the literature. In [Kramer], Kramer iteratively evaluates the ability of a set of sensors to observe the modes of a system. More recently, genetic algorithms 1-3 and neural networks 4 have been developed to identify optimal sensor locations. In 5, a Bayesian approach is used that takes into account the risk of different types of errors and the distribution of damage rates. In 6, a finite element model was leveraged to identify the sensor locations most likely to detect damage. In most of the sensor placement algorithms presented in the literature, data from the damaged structure, whether simulated or measured, is required. One advantage of the embedded sensitivity approach is that the sensor locations can be determined from the healthy structure.
Another advantage of ESFs is that material properties need not be explicitly known. Instead, the material properties are &#34;embedded&#34; in the expressions for the system&#39;s FRFs. Therefore, all that is needed to calculate ESFs are a set of measured FRFs at particular input/output locations. Specifically, the sensitivity of the FRF (Hjk) calculated from a response measured at point j to an input at point k, to a change in stiffness (Kmn) between points m and n is
<img alt="Equation1" src="/files/ftp_upload/53690/53690equation1.jpg" />
where <img alt="Equation2" src="/files/ftp_upload/53690/53690equation2.jpg" /> is the ESF as a function of frequency, &#969; 7-9. The procedure for measuring the FRFs required to calculate the right-hand side of equation (1) is detailed in the next section and demonstrated in the video.

<table border="0" cellpadding="0" cellspacing="0" width="573">
	<tbody>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Accelerometer</td>
			<td style="width:71px;">PCB</td>
			<td style="width:119px;">356B11</td>
			<td style="width:167px;">three used in testing</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Impact hammer</td>
			<td style="width:71px;">PCB</td>
			<td style="width:119px;">086C01</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Data acquisition card</td>
			<td style="width:71px;">NI</td>
			<td align="right" style="width:119px;">9234</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">DAQ chasis&#160;</td>
			<td style="width:71px;">NI</td>
			<td style="width:119px;">cDAQ-9171</td>
			<td>or similar</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Software</td>
			<td style="width:71px;">MATLAB</td>
			<td style="width:119px;"></td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Super glue</td>
			<td style="width:71px;">Loctite</td>
			<td align="right" style="width:119px;">454</td>
			<td></td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:216px;">Handheld Shaker</td>
			<td style="width:71px;">PCB</td>
			<td style="width:119px;">394C06</td>
			<td>for calibration&#160;</td>
		</tr>
	</tbody>
</table>

data acquisition protocol for determining embedded sensitivity functions

The effectiveness of many structural health monitoring techniques depends on the placement of sensors and the location of input forces. Algorithms for determining optimal sensor and forcing locations typically require data, either simulated or measured, from the damaged structure. Embedded sensitivity functions provide an approach for determining the best available sensor location to detect damage with only data from the healthy structure. In this video and manuscript, the data acquisition procedure and best practices for determining the embedded sensitivity functions of a structure is presented. The frequency response functions used in the calculation of the embedded sensitivity functions are acquired using modal impact testing. Data is acquired and representative results are shown for a residential scale wind turbine blade. Strategies for evaluating the quality of the data being acquired are provided during the demonstration of the data acquisition process.

Figure 1 shows a typical embedded sensitivity function. Similar to an FRF, the ESF has peaks near the natural frequencies of the structure. The higher the value of the ESF, the more sensitive the location is to damage between points m and n. Each of the thirty points tested on the wind turbine blade has a unique ESF. These ESFs can be compared to determine which sensor location would be most sensitive to damage. For example, Figure 2 shows the amplitudes of the ESFs near 142 Hz. From this plot, it is clear that sensor locations corresponding to the squares in the first and third columns are most sensitive to the damage. Note that these locations are determined from data acquired from the healthy blade.
Figure 3 shows the measured difference in FRFs between the FRFs determined from data from the healthy blade and those determined from data from the damaged blade. The similarities between the difference in FRFs and the ESFs show the effectiveness of the ESFs to predict the locations at which the largest changes in FRFs due to damage will be exhibited.
<img alt="Figure 1" src="/files/ftp_upload/53690/53690fig1.jpg" /> 
Figure 1. The amplitude of the embedded sensitivity function for point 1. The value of the ESF corresponds to the sensitivity of the FRF at point 1 to damage in the structure at the chosen location. The values change as a function of frequency. Peaks in the ESF tend to correspond to natural frequencies of the structure. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53690/53690fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" src="/files/ftp_upload/53690/53690fig2.jpg" /> 
Figure 2. The amplitudes of the ESFs for all thirty points at 142 Hz. Each colored square corresponds to the value of the ESF at 142 Hz for each spatial location tested. Hot colors correspond to points at which the ESFs predict the largest change in FRF due to damage. Cooler colors indicate that the change in FRF at that point will be relatively small. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53690/53690fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" src="/files/ftp_upload/53690/53690fig3.jpg" /> 
Figure 3. The difference in the FRFs, Hjk, for all thirty points at 142 Hz. The differences were calculated by subtracting the FRFs determined from the healthy and damaged blades. Hot colors indicate large differences in FRFs. Cool colors indicate small changes in FRFs. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53690/53690fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" src="/files/ftp_upload/53690/53690fig4.jpg" /> 
Figure 4. Impact points used during testing. Points were chosen to span the blade. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53690/53690fig4large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Data Acquisition Protocol for Determining Embedded Sensitivity Functions at JoVE.com

Data Acquisition Protocol for Determining Embedded Sensitivity Functions

The data acquisition procedure for determining embedded sensitivity functions is described. Data is acquired and representative results are shown for a residential scale wind turbine blade.

The effectiveness of many structural health monitoring techniques depends on the placement of sensors and the location of input forces. Algorithms for ...

data-acquisition-protocol-for-determining-embedded-sensitivity

Nanyang Technological University

Research

JoVE Journal

Engineering

6.0K Views.  Vanderbilt University. The data acquisition procedure for determining embedded sensitivity functions is described. Data is acquired and representative results are shown for a residential scale wind turbine blade.

Video: Data Acquisition Protocol for Determining Embedded Sensitivity Functions

Determining 3D Flow Fields via Multi-camera Light Field Imaging

In the field of fluid mechanics, the resolution of computational schemes has outpaced experimental methods and widened the gap between predicted and observed phenomena in fluid flows. Thus, a need exists for an accessible method capable of resolving three-dimensional (3D) data sets for a range of problems. We present a novel technique for performing quantitative 3D imaging of many types of flow fields. The 3D technique enables investigation of complicated velocity fields and bubbly flows. Measurements of these types present a variety of challenges to the instrument. For instance, optically dense bubbly multiphase flows cannot be readily imaged by traditional, non-invasive flow measurement techniques due to the bubbles occluding optical access to the interior regions of the volume of interest. By using Light Field Imaging we are able to reparameterize images captured by an array of cameras to reconstruct a 3D volumetric map for every time instance, despite partial occlusions in the volume. The technique makes use of an algorithm known as synthetic aperture (SA) refocusing, whereby a 3D focal stack is generated by combining images from several cameras post-capture 1. Light Field Imaging allows for the capture of angular as well as spatial information about the light rays, and hence enables 3D scene reconstruction. Quantitative information can then be extracted from the 3D reconstructions using a variety of processing algorithms. In particular, we have developed measurement methods based on Light Field Imaging for performing 3D particle image velocimetry (PIV), extracting bubbles in a 3D field and tracking the boundary of a flickering flame. We present the fundamentals of the Light Field Imaging methodology in the context of our setup for performing 3DPIV of the airflow passing over a set of synthetic vocal folds, and show representative results from application of the technique to a bubble-entraining plunging jet.

A technique for performing quantitative three-dimensional (3D) imaging for a range of fluid flows is presented. Using concepts from the area of Light Field Imaging, we reconstruct 3D volumes from arrays of images. Our 3D results span a broad range including velocity fields and multi-phase bubble size distributions.

In the field of fluid mechanics, the resolution of computational schemes has outpaced experimental methods and widened the gap between predicted and ...

Quasi-light Storage for Optical Data Packets

Today's telecommunication is based on optical packets which transmit the information in optical fiber networks around the world. Currently, the processing of the signals is done in the electrical domain. Direct storage in the optical domain would avoid the transfer of the packets to the electrical and back to the optical domain in every network node and, therefore, increase the speed and possibly reduce the energy consumption of telecommunications. However, light consists of photons which propagate with the speed of light in vacuum. Thus, the storage of light is a big challenge. There exist some methods to slow down the speed of the light, or to store it in excitations of a medium. However, these methods cannot be used for the storage of optical data packets used in telecommunications networks. Here we show how the time-frequency-coherence, which holds for every signal and therefore for optical packets as well, can be exploited to build an optical memory. We will review the background and show in detail and through examples, how a frequency comb can be used for the copying of an optical packet which enters the memory. One of these time domain copies is then extracted from the memory by a time domain switch. We will show this method for intensity as well as for phase modulated signals.

The article describes a procedure to store optical data packets with an arbitrary modulation, wavelength, and data rate. These packets are the basis of modern telecommunications.

Today's telecommunication is based on optical packets which transmit the information in optical fiber networks around the world. Currently, the processing ...

Probing C84-embedded Si Substrate Using Scanning Probe Microscopy and Molecular Dynamics

This paper reports an array-designed C84-embedded Si substrate fabricated using a controlled self-assembly method in an ultra-high vacuum chamber. The characteristics of the C84-embedded Si surface, such as atomic resolution topography, local electronic density of states, band gap energy, field emission properties, nanomechanical stiffness, and surface magnetism, were examined using a variety of surface analysis techniques under ultra, high vacuum (UHV) conditions as well as in an atmospheric system. Experimental results demonstrate the high uniformity of the C84-embedded Si surface fabricated using a controlled self-assembly nanotechnology mechanism, represents an important development in the application of field emission display (FED), optoelectronic device fabrication, MEMS cutting tools, and in efforts to find a suitable replacement for carbide semiconductors. Molecular dynamics (MD) method with semi-empirical potential can be used to study the nanoindentation of C84-embedded Si substrate. A detailed description for performing MD simulation is presented here. Details for a comprehensive study on mechanical analysis of MD simulation such as indentation force, Young&#39;s modulus, surface stiffness, atomic stress, and atomic strain are included. The atomic stress and von-Mises strain distributions of the indentation model can be calculated to monitor deformation mechanism with time evaluation in atomistic level.

Probing C84-embedded Si Substrate Using Scanning Probe Microscopy and Molecular Dynamics

This paper reports the nanomaterial fabrication of a fullerene Si substrate inspected and verified by nanomeasurements and molecular dynamic simulation.

This paper reports an array-designed C84-embedded Si substrate fabricated using a controlled self-assembly method in an ultra-high vacuum chamber. The ...

Scalable Solution-processed Fabrication Strategy for High-performance, Flexible, Transparent Electrodes with Embedded Metal Mesh

Here, the authors report the embedded metal-mesh transparent electrode (EMTE), a new transparent electrode (TE) with a metal mesh completely embedded in a polymer film. This paper also presents a low-cost, vacuum-free fabrication method for this novel TE; the approach combines lithography, electroplating, and imprint transfer (LEIT) processing. The embedded nature of the EMTEs offers many advantages, such as high surface smoothness, which is essential for organic electronic device production; superior mechanical stability during bending; favorable resistance to chemicals and moisture; and strong adhesion with plastic film. LEIT fabrication features an electroplating process for vacuum-free metal deposition and is favorable for industrial mass production. Furthermore, LEIT allows for the fabrication of metal mesh with a high aspect ratio (i.e., thickness to linewidth), significantly enhancing its electrical conductance without adversely losing optical transmittance. We demonstrate several prototypes of flexible EMTEs, with sheet resistances lower than 1 &#937;/sq and transmittances greater than 90%, resulting in very high figures of merit (FoM) &#8211; up to 1.5 x 104 &#8211; which are amongst the best values in the published literature.

This protocol describes a solution-based fabrication strategy for high-performance, flexible, transparent electrodes with fully-embedded, thick metal mesh. Flexible transparent electrodes fabricated by this process demonstrate among the highest reported performances, including ultra-low sheet resistance, high optical transmittance, mechanical stability under bending, strong substrate adhesion, surface smoothness, and environmental stability.

Here, the authors report the embedded metal-mesh transparent electrode (EMTE), a new transparent electrode (TE) with a metal mesh completely embedded in a ...

Production and Characterization of Vacuum Deposited Organic Light Emitting Diodes

A method for producing simple and efficient thermally-activated delayed fluorescence organic light-emitting diodes (OLEDs) based on guest-host or exciplex donor-acceptor emitters is presented. With a step-by-step procedure, readers will be able to repeat and produce OLED devices based on simple organic emitters. A patterning procedure allowing the creation of personalized indium tin oxide (ITO) shape is shown. This is followed by the evaporation of all layers, encapsulation and characterization of each individual device. The end goal is to present a procedure that will give the opportunity to repeat the information presented in cited publication but also using different compounds and structures in order to prepare efficient OLEDs.

A protocol for the production of simple structured organic light-emitting diodes (OLEDs) is presented.

A method for producing simple and efficient thermally-activated delayed fluorescence organic light-emitting diodes (OLEDs) based on guest-host or exciplex ...

An Efficient Method for Selective Desalination of Radioactive Iodine Anions by Using Gold Nanoparticles-Embedded Membrane Filter

Here, we demonstrate a detail protocol for the preparation of nanomaterials-embedded composite membranes and its application to the efficient and ion-selective removal of radioactive iodines. By using citrate-stabilized gold nanoparticles (mean diameter: 13 nm) and cellulose acetate membranes, gold nanoparticle-embedded cellulose acetate membranes (Au-CAM) have easily been fabricated. The nano-adsorbents on Au-CAM were highly stable in the presence of high concentration of inorganic salts and organic molecules. The iodide ions in aqueous solutions could rapidly be captured by this engineered membrane. Through a filtration process using an Au-CAM containing filter unit, excellent removal efficiency (&gt;99%) as well as ion-selective desalination result was achieved in a short time. Moreover, Au-CAM provided good reusability without significant decrease of its performances. These results suggested that the present technology using the engineered hybrid membrane will be a promising process for the large-scale decontamination of radioactive iodine from liquid wastes.

An efficient method for the rapid and ion-selective desalination of radioactive iodine in several aqueous solutions is described by using gold nanoparticles-immobilized cellulose acetate membrane filters.

Here, we demonstrate a detail protocol for the preparation of nanomaterials-embedded composite membranes and its application to the efficient and ...

Automated Deployment of an Internet Protocol Telephony Service on Unmanned Aerial Vehicles Using Network Functions Virtualization

The Network Function Virtualization (NFV) paradigm is one of the key enabling technologies in the development of the 5th generation of mobile networks. This technology aims to lessen the dependence on hardware in the provision of network functions and services by using virtualization techniques that allow the softwarization of those functionalities over an abstraction layer. In this context, there is increasing interest in exploring the potential of unmanned aerial vehicles (UAVs) to offer a flexible platform capable of enabling cost-effective NFV operations over delimited geographic areas.
To demonstrate the practical feasibility of utilizing NFV technologies in UAV platforms, a protocol is presented to set up a functional NFV environment based on open source technologies, in which a set of small UAVs supply the computational resources that support the deployment of moderately complex network services. Then, the protocol details the different steps needed to support the automated deployment of an internet protocol (IP) telephony service over a network of interconnected UAVs, leveraging the capacities of the configured NFV environment. Experimentation results demonstrate the proper operation of the service after its deployment. Although the protocol focuses on a specific type of network service (i.e., IP telephony), the described steps may serve as a general guide to deploy other type of network services. On the other hand, the protocol description considers concrete equipment and software to set up the NFV environment (e.g., specific single board computers and open source software). The utilization of other hardware and software platforms may be feasible, although the specific configuration aspect of the NFV environment and the service deployment may present variations with respect to those described in the protocol.

The objective of the described protocol is twofold: to configure a network functions virtualization environment using unmanned aerial vehicles as computational entities providing the underlying structure to execute virtualized network functions and to use this environment to support the automated deployment of a functional internet protocol telephony service over the aerial vehicles.

The Network Function Virtualization (NFV) paradigm is one of the key enabling technologies in the development of the 5th generation of mobile networks. ...

Terahertz Imaging and Characterization Protocol for Freshly Excised Breast Cancer Tumors

This manuscript presents a protocol to handle, characterize, and image freshly excised human breast tumors using pulsed terahertz imaging and spectroscopy techniques. The protocol involves terahertz transmission mode at normal incidence and terahertz reflection mode at an oblique angle of 30&#176;. The collected experimental data represent time domain pulses of the electric field. The terahertz electric field signal transmitted through a fixed point on the excised tissue is processed, through an analytical model, to extract the refractive index and absorption coefficient of the tissue. Utilizing a stepper motor scanner, the terahertz emitted pulse is reflected from each pixel on the tumor providing a planar image of different tissue regions. The image can be presented in time or frequency domain. Furthermore, the extracted data of the refractive index and absorption coefficient at each pixel are utilized to provide a tomographic terahertz image of the tumor. The protocol demonstrates clear differentiation between cancerous and healthy tissues. On the other hand, not adhering to the protocol can result in noisy or inaccurate images due to the presence of air bubbles and fluid remains on the tumor surface. The protocol provides a method for surgical margins assessment of breast tumors.

Freshly excised human breast cancer tumors are characterized with terahertz spectroscopy and imaging following fresh tissue handling protocols. Tissue positioning is taken into consideration to enable effective characterization while providing analysis in a timely manner for future intraoperative applications.

This manuscript presents a protocol to handle, characterize, and image freshly excised human breast tumors using pulsed terahertz imaging and spectroscopy ...

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

The mechanical strengthening of metals is the long-standing challenge and popular topic of materials science in industries and academia. The size dependence of the strength of the nanometals has been attracting a lot of interest. However, characterizing the strength of materials at the lower nanometer scale has been a big challenge because the traditional techniques become no longer effective and reliable, such as nano-indentation, micropillar compression, tensile, etc. The current protocol employs radial diamond-anvil cell (rDAC) X-ray diffraction (XRD) techniques to track differential stress changes and determine the strength of ultrafine metals. It is found that ultrafine nickel particles have more significant yield strength than coarser particles, and the size strengthening of nickel continues down to 3 nm. This vital finding immensely depends on effective and reliable characterizing techniques. The rDAC XRD method is expected to play a significant role in studying and exploring nanomaterial mechanics.

The protocol presented here describes the high-pressure radial diamond-anvil-cell experiments and analyzing the related data, which are essential for obtaining the mechanical strength of the nanomaterials with a significant breakthrough to the traditional approach.

The mechanical strengthening of metals is the long-standing challenge and popular topic of materials science in industries and academia. The size ...

Data Communication Based on MQTT in a Polymer Extrusion Process

This work aims at building a flexible data communication structure for a polymer processing machine by employing a publisher-subscriber based protocol called Message Queuing Telemetry Transport (MQTT), which is operated over TCP/IP. Even when using conventional equipment, processing data can be measured and recorded by various devices anywhere through an Internet communication. A message-based protocol allows flexible communication that overcomes the shortcomings of the existing server-client protocol. Multiple devices can subscribe to the processing data published by source devices. The proposed method facilitates data communication between multiple publishers and subscribers. This work has implemented a system that publishes data from the equipment and additional sensors to a message broker. The subscribers can monitor and store the process data relayed by the broker. The system has been deployed and run for a film extrusion line to demonstrate the effectiveness.

This work proposes a flexible method for data communication between a film extrusion system and monitoring devices based on a message protocol called Message Queuing Telemetry Transport (MQTT).

This work aims at building a flexible data communication structure for a polymer processing machine by employing a publisher-subscriber based protocol ...