This work was supported by the National Science Foundation (through grants DMR-1121107, CMMI-1363483 and Graduate Research Fellowships (GRF-1106401) to C.W.S., D.F.C. and K.A.O.) and the National Institutes of Health (R21GM111584). The authors have no conflicts of interest.

1. Photolithography
<ol>
	<li>Design the photomask using an appropriate software package and submit the design to a qualified photomask printer.21</li>
	<li>In a clean room facility, rinse a 6&#34; single-side polished Si wafer with a steady stream of acetone (&#8805;99.5%; see Table 1) followed by a steady stream of methanol (99.8%; see Table 1). Dry the wafer by spraying with N2 gas and placing the wafer on a hot plate at 95 &#176;C for 2 min. 
	NOTE: The doping profile and crystal orientation of the wafers do not affect the following procedures.</li>
	<li>Protect the trough outside of the spin coater (in a standard spin coat hood) by covering with a sheet of Al foil and place the clean Si wafer on the center of the vacuum chuck in the spin coater to secure the wafer.</li>
	<li>Deposit positive photoresist directly onto the center of the wafer by carefully pouring until the photoresist covers most of the wafer. Take care to ensure there are no bubbles in the photoresist. 
	NOTE: The exact procedures in Steps 1.5-1.10 correspond to the photoresist shown in Table 1; different procedures may be required for different photoresists.</li>
	<li>Start the spin cycle by performing the following procedures:
	<ol>
		<li>Program a speed of 300 rpm, a ramp of 100 rpm/sec, and a spin time of 5 sec to begin the spin cycle.</li>
		<li>Program to a speed of 1,800 rpm, a ramp of 1,000 rpm/sec, and a spin time of 60 sec to evenly spread the photoresist.</li>
		<li>Program to a speed of 0 rpm, a ramp of 1,000 rpm/sec, and a spin time of 0 sec to conclude the spin cycle.</li>
	</ol>
	</li>
	<li>Release the vacuum on the chuck and use wafer tweezers to retrieve the wafer from the chuck. Then place the wafer onto a hot plate to bake at 110 &#176;C for 165 sec. 
	NOTE: This step is referred to as the &#34;soft bake&#34;.</li>
	<li>Load the photomask into the holder of a mask aligner/photolithography machine.</li>
	<li>Edit the parameters of the photolithography machine to provide an energy dosage of 1,400 mJ/cm2 (e.g., for an output intensity of 13.5 mW/cm2, use an exposure time of &#8764;103.7 sec).</li>
	<li>Remove the photopatterned wafer from the holder and place it in a solution of its corresponding developer (see Table 1) for 5 min.</li>
	<li>Remove the wafer from the developer, wash the wafer with a steady stream of deionized H2O and dry it with N2 gas. 
	NOTE: Over-developing may cause patterns to swell, while under-developing may cause incomplete removal of the photoresist along the photo-patterned features.</li>
	<li>Inspect the wafer under a microscope to confirm the patterns printed on the photomask were transferred to the photoresist.</li>
</ol>
2. Deep Reactive Ion Etching
<ol>
	<li>Load the photo-patterned Si wafer into the chamber of a deep reactive ion etching instrument and etch the fluidic channels into the Si wafer to the desired depth following standard etching procedures.22</li>
	<li>Carefully unload the sample from the chamber after the etching process is complete.</li>
	<li>To remove excess photoresist from the wafer, prepare a large beaker with a solution of photoresist remover (see Table 1) in a well-ventilated hood dedicated to solvent use and place it on a hot plate at 65 &#176;C.</li>
	<li>Submerge the wafer in the photoresist removal solution and let it soak for 1 hr. 
	NOTE: Different solutions can be used to remove photoresist (e.g., a solution of acetone (&#8805;99.5%; see Table 1) can remove the photoresist by soaking overnight).</li>
	<li>Remove the wafer from the beaker and rinse it with alternating streams of acetone (&#8805;99.5%; see Table 1) and isopropyl alcohol (&#8805;99.7%; see Table 1). Dry the wafer with N2 gas.</li>
</ol>
3. Piranha Cleaning
<ol>
	<li>In a well-ventilated hood (dedicated to the use of acids), prepare a piranha solution by adding H2O2 (30.0 wt.% in water; see Table 1) to H2SO4 (95.0-98.0%; see Table 1) to in a 1:3 ratio in a large, clean beaker. 
	CAUTION: Piranha solutions are highly corrosive, are a strong oxidizer and are highly dangerous. Take extreme care in handling piranha solutions and wear the proper safety equipment.</li>
	<li>Submerge the ion etched wafer with the etched-features facing up and leave for 5 min. Carefully remove the wafer and fully rinse with deionized H2O.</li>
	<li>Re-submerge the wafer in the piranha solution for 2 min. Carefully remove the wafer and fully rinse with copious deionized H2O.</li>
	<li>In a separate well-ventilated hood dedicated to solvent use, wash the wafer with a steady stream of acetone (&#8805;99.5%; see Table 1) followed by a steady stream of methanol (99.8%; see Table 1) and dry the wafer with N2 gas. Dispose of the piranha solution by following the appropriate safety procedures.</li>
</ol>
4. Prepare the Borosilicate Glass Lid
<ol>
	<li>Using a scribe tool, etch straight lines into the borosilicate glass to create rectangular segments (e.g., 8 x 4 cm2). Carefully snap the glass to recover the rectangular segments.</li>
	<li>Take one of these glass segments and place it on top of a printed copy of the desired design (with actual dimensions) to mark the location of the inlets and outlets on the glass with a black marker.</li>
	<li>Drill the inlet and outlet holes into the borosilicate glass. 
	NOTE: Proper safety equipment should be worn at all times.
	<ol>
		<li>Fix a 1/8&#34; drill bit into the mouth of drill press. Place the rectangular glass segment on top of an Al plate with drilled holes so that the marks on the glass are above the holes in the Al plate. Secure the glass on the Al plate with tape.</li>
		<li>Carefully lower the feed handle to start drilling small holes into the glass and continue to lower the handle until the hole is made through the glass. Once the hole is finished, remove the tape and slowly lift the glass to remove the glass powder. Place the glass powder in a beaker with water and discard using the appropriate safety procedures.</li>
		<li>Carefully dry the glass with a non-lint-producing absorbent cloth and follow the same procedures (Steps 4.3.1-4.3.2) to drill the other inlet and outlet holes.</li>
	</ol>
	</li>
	<li>Follow the same procedure (Section 3, above) to clean the rectangular glass segment with piranha solution. 
	CAUTION: Piranha solutions are highly corrosive, are a strong oxidizer and are highly dangerous. Take extreme care in handling piranha solutions and wear the proper safety equipment.</li>
</ol>
5. Anodic Bonding
<ol>
	<li>Using a scribe tool, etch straight lines into the Si wafer around the perimeter of the microfluidic chip such that it is slightly smaller than the rectangular glass segment (e.g., 7 x 3 cm2). Carefully snap the wafer along the etched lines.</li>
	<li>Rinse the Si segment with a steady stream of acetone (&#8805;99.5%; see Table 1) followed by a steady stream of methanol (99.8%; see Table 1). Place the wafer on a hot plate at 95 &#176;C for 2 min to dry.</li>
	<li>With the etched-features on the Si segment facing up, carefully add the clean glass on top of the Si segment and make sure the holes align properly.</li>
	<li>Carefully flip the segments while ensuring the holes are kept aligned. Since the glass segment is larger than the Si segment, secure the two segments with double-sided tape where half of the tape secures the vertical edges of the Si segment and the other half of the tape secures the overhanging glass. Then flip the segments again such that the glass segment is on top, and place the segments on top of a metal slab on a hot plate.</li>
	<li>Carefully add a second metal slab (e.g., steel) of a sufficiently heavy weight (i.e., at least 5 kg) directly to the top of the assembled glass and Si segments. 
	NOTE: This metal slab should not be in contact with the Si segment or the conductive tape.</li>
	<li>Using a high voltage power supply, connect one lead (power) to the metallic slab on top of the assembled glass and Si segments and the other lead (ground) to the bottom metallic slab.</li>
	<li>Turn the voltage on the underlying hot plate to 1,000 V. Check the applied voltage by using multimeter; press one probe against the bottom plate and the other probe against the top plate. 
	CAUTION: The high voltage is extremely dangerous; be careful not to touch the metallic slabs or the connecting wires.</li>
	<li>Leave the hot plate at 450 &#176;C for 2 hr to allow the glass &#34;lid&#34; to anodically bond to the Si substrate. Return after 2 hr to turn off the hot plate, turn off the DC power supply and remove the device from the metallic slabs. 
	WARNING: The metallic slabs will be extremely hot during and after the bonding process, so allow the materials to cool for at least 1 hr after turning off the hot plate.</li>
</ol>
6. Finalizing the Acoustofluidic Device
<ol>
	<li>Scrape the surface of the glass with a razor to remove grime produced by the anodic bonding and clean the surface of the glass with acetone.</li>
	<li>Prepare a sheet of polydimethylsiloxane (PDMS) approximately 5 mm thick and cut several small, square slabs approximately 10 x 10 mm2 (see Table 1).23</li>
	<li>Use a 3 mm biopsy punch to cut one hole in the center of each PDMS slab so as to insert the silicone tubing through it. Place the slabs directly on top the holes on the glass substrate and glue the slabs with epoxy. 
	NOTE: Be careful not to use too much glue as it will occlude the holes of the device.</li>
	<li>Carefully glue the lead zirconate titanate (PZT) transducer to the Si segment on the back side of the device, centered-underneath the microchannel.</li>
	<li>Solder two wires to the two conductive areas on the PZT transducer. Take care that the wires are securely attached to the PZT transducer. Insert the silicone tubing through the holes in the slabs of PDMS and add additional glue around slabs and the tubing to secure their attachment.</li>
</ol>
7. Operating the Acoustofluidic Device
<ol>
	<li>Securely mount the device onto a microscope stage with the microchannel directly underneath the objective. 
	NOTE: Ensure the PZT transducer does not make contact with the stage by placing a small insert underneath the device.</li>
	<li>Using standardized connectors, connect the silicone tubes from the outlets of the device to syringes secured on syringe pumps. 
	NOTE: This configuration is intended for &#34;withdrawal mode&#34;; syringe pumps may alternatively be used to inject the sample into the device.</li>
	<li>Place the silicone tube leading to the inlet of the device in a vial containing the fluid sample (e.g., a suspension of polystyrene beads or cells).</li>
	<li>Place the vial containing the fluid sample on a stir plate to continuously mix the sample and ensure that a constant concentration of particles or cells is maintained throughout the course of the experiment.</li>
	<li>Connect the wires from the PZT transducer to the output from a power amplifier in series with a function generator. Program the settings on the function generator (e.g., peak-to-peak voltage and frequency) and monitor the output signal from the amplifier using an oscilloscope. Turn on the function generator and power amplifier to begin actuating the PZT transducer.6
	<ol>
		<li>To estimate the resonant frequency of the device, follow the equation c = &#955; * &#402;, where c is the speed of sound of the medium (i.e., water), &#955; is the acoustic wavelength and &#402; is the frequency of the PZT transducer. In the case of a half-wavelength harmonic (which we show in the Representative Results Section), the width of the microchannel should be half the length of the standing wave.</li>
		<li>Use a peak-to-peak voltage setting within the range of 0-50 V. 
		NOTE: An increase in the applied voltage results in higher pressure amplitudes, and thus, more rapid acoustophoresis.</li>
	</ol>
	</li>
	<li>Turn on the microscope and ensure the microfluidic channel is clearly in focus.</li>
	<li>Turn on the syringe pump to apply flow and introduce the sample into the device. Monitor the entities flowing through the device with the microscope on fluorescence mode.</li>
	<li>Ensure the device efficiently focuses particles by adjusting the peak-to-peak voltage supplied to the PZT transducer to modify the pressure amplitude and by performing a frequency sweep near the expected resonant frequency to identify the empirical resonant frequency.</li>
</ol>

<ol>
	<li>Laurell, T., Petersson, F., Nilsson, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Chip+integrated+strategies+for+acoustic+separation+and+manipulation+of+cells+and+particles.">Chip integrated strategies for acoustic separation and manipulation of cells and particles.</a> Chem Soc Rev. 36 (3), 492-506 (2007).</li><li>Ding, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Surface+acoustic+wave+microfluidics.">Surface acoustic wave microfluidics.</a> Lab Chip. 13 (18), 3626-3649 (2013).</li><li>Schmid, L., Weitz, D. A., Franke, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sorting+drops+and+cells+with+acoustics:+acoustic+microfluidic+fluorescence-activated+cell+sorter.">Sorting drops and cells with acoustics: acoustic microfluidic fluorescence-activated cell sorter.</a> Lab Chip. 14 (19), 3710-3718 (2014).</li><li>Guo, F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Controlling+cell-cell+interactions+using+surface+acoustic+waves.">Controlling cell-cell interactions using surface acoustic waves.</a> Proc Natl Acad Sci U S A. 112 (1), 43-48 (2015).</li><li>Li, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustic+separation+of+circulating+tumor+cells.">Acoustic separation of circulating tumor cells.</a> Proc Natl Acad Sci U S A. 112 (16), 4970-4975 (2015).</li><li>Gao, L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two-dimensional+spatial+manipulation+of+microparticles+in+continuous+flows+in+acoustofluidic+systems.">Two-dimensional spatial manipulation of microparticles in continuous flows in acoustofluidic systems.</a> Biomicrofluidics. 9 (1), 014105 (2015).</li><li>Bruus, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustofluidics+7:+The+acoustic+radiation+force+on+small+particles.">Acoustofluidics 7: The acoustic radiation force on small particles.</a> Lab Chip. 12 (6), 1014-1021 (2012).</li><li>Shields, C. W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nucleation+and+growth+synthesis+of+siloxane+gels+to+form+functional,+monodisperse,+and+acoustically+programmable+particles.">Nucleation and growth synthesis of siloxane gels to form functional, monodisperse, and acoustically programmable particles.</a> Angew Chem Int Ed Engl. 53 (31), 8070-8073 (2014).</li><li>Petersson, F., Nilsson, A., Holm, C., Jonsson, H., Laurell, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Separation+of+lipids+from+blood+utilizing+ultrasonic+standing+waves+in+microfluidic+channels.">Separation of lipids from blood utilizing ultrasonic standing waves in microfluidic channels.</a> Analyst. 129 (10), 938-943 (2004).</li><li>Cushing, K. W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Elastomeric+negative+acoustic+contrast+particles+for+affinity+capture+assays.">Elastomeric negative acoustic contrast particles for affinity capture assays.</a> Anal Chem. 85 (4), 2208-2215 (2013).</li><li>Johnson, L. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Elastomeric+microparticles+for+acoustic+mediated+bioseparations.">Elastomeric microparticles for acoustic mediated bioseparations.</a> J Nanobiotechnology. 11, 22 (2013).</li><li>Shields, C. W., Johnson, L. M., Gao, L., Lopez, G. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Elastomeric+negative+acoustic+contrast+particles+for+capture,+acoustophoretic+transport,+and+confinement+of+cells+in+microfluidic+systems.">Elastomeric negative acoustic contrast particles for capture, acoustophoretic transport, and confinement of cells in microfluidic systems.</a> Langmuir. 30 (14), 3923-3927 (2014).</li><li>Shields, C. W., Reyes, C. D., Lopez, G. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+cell+sorting:+a+review+of+the+advances+in+the+separation+of+cells+from+debulking+to+rare+cell+isolation.">Microfluidic cell sorting: a review of the advances in the separation of cells from debulking to rare cell isolation.</a> Lab Chip. 15, 1230-1249 (2015).</li><li>Goddard, G., Martin, J. C., Graves, S. W., Kaduchak, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultrasonic+particle-concentration+for+sheathless+focusing+of+particles+for+analysis+in+a+flow+cytometer.">Ultrasonic particle-concentration for sheathless focusing of particles for analysis in a flow cytometer.</a> Cytometry A. 69 (2), 66-74 (2006).</li><li>Goddard, G. R., Sanders, C. K., Martin, J. C., Kaduchak, G., Graves, S. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Analytical+Performance+of+an+Ultrasonic+Particle+Focusing+Flow+Cytometer.">Analytical Performance of an Ultrasonic Particle Focusing Flow Cytometer.</a> Anal Chem. 79 (22), 8740-8746 (2007).</li><li>Goddard, G., Kaduchak, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultrasonic+particle+concentration+in+a+line-driven+cylindrical+tube.">Ultrasonic particle concentration in a line-driven cylindrical tube.</a> J Acoust Soc Am. 117 (6), 3440 (2005).</li><li>Lenshof, A., Magnusson, C., Laurell, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustofluidics+8:+applications+of+acoustophoresis+in+continuous+flow+microsystems.">Acoustofluidics 8: applications of acoustophoresis in continuous flow microsystems.</a> Lab Chip. 12 (7), 1210-1223 (2012).</li><li>Carugo, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+thin-reflector+microfluidic+resonator+for+continuous-flow+concentration+of+microorganisms:+a+new+approach+to+water+quality+analysis+using+acoustofluidics.">A thin-reflector microfluidic resonator for continuous-flow concentration of microorganisms: a new approach to water quality analysis using acoustofluidics.</a> Lab Chip. 14 (19), 3830-3842 (2014).</li><li>Austin Suthanthiraraj, P. P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=One-dimensional+acoustic+standing+waves+in+rectangular+channels+for+flow+cytometry.">One-dimensional acoustic standing waves in rectangular channels for flow cytometry.</a> Methods. 57 (3), 259-271 (2012).</li><li>Wiklund, M., Nilsson, S., Hertz, H. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultrasonic+trapping+in+capillaries+for+trace-amount+biomedical+analysis.">Ultrasonic trapping in capillaries for trace-amount biomedical analysis.</a> J App Phys. 90 (1), 421 (2001).</li><li>Shields, C. W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Field-directed+assembly+of+patchy+anisotropic+microparticles+with+defined+shape.">Field-directed assembly of patchy anisotropic microparticles with defined shape.</a> Soft Matter. 9 (38), 9219 (2013).</li><li>Yeom, J., Wu, Y., Selby, J. C., Shannon, M. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Maximum+achievable+aspect+ratio+in+deep+reactive+ion+etching+of+silicon+due+to+aspect+ratio+dependent+transport+and+the+microloading+effect.">Maximum achievable aspect ratio in deep reactive ion etching of silicon due to aspect ratio dependent transport and the microloading effect.</a> J Vac Sci Technol B Microelectron Nanometer Struct Process Meas Phenom. 23 (6), 2319 (2005).</li><li>McDonald, J. C., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Poly(dimethylsiloxane)+as+a+material+for+fabricating+microfluidic+devices.">Poly(dimethylsiloxane) as a material for fabricating microfluidic devices.</a> Acc Chem Res. 35 (7), 491-499 (2002).</li><li>Golden, J. P., Justin, G. A., Nasir, M., Ligler, F. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hydrodynamic+focusing--a+versatile+tool.">Hydrodynamic focusing--a versatile tool.</a> Anal Bioanal Chem. 402 (1), 325-335 (2012).</li><li>Hejazian, M., Li, W., Nguyen, N. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Lab+on+a+chip+for+continuous-flow+magnetic+cell+separation.">Lab on a chip for continuous-flow magnetic cell separation.</a> Lab Chip. 15 (4), 959-970 (2015).</li><li>Shields, C. W., Livingston, C. E., Yellen, B. B., L&#242;pez, G. P., Murdoch, D. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Magnetographic+array+for+the+capture+and+enumeration+of+single+cells+and+cell+pairs.">Magnetographic array for the capture and enumeration of single cells and cell pairs.</a> Biomicrofluidics. 8 (4), 041101 (2014).</li><li>Voldman, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Electrical+forces+for+microscale+cell+manipulation.">Electrical forces for microscale cell manipulation.</a> Annu Rev Biomed Eng. 8, 425-454 (2006).</li><li>Di Carlo, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Inertial+microfluidics.">Inertial microfluidics.</a> Lab Chip. 9 (21), 3038-3046 (2009).</li><li>Earnshaw, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=On+the+nature+of+the+molecular+forces+which+regulate+the+constitution+of+the+luminferous+ether.">On the nature of the molecular forces which regulate the constitution of the luminferous ether.</a> Trans Camb Phil Soc. 7, 97-112 (1842).</li><li>Piyasena, M. E., Graves, S. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+intersection+of+flow+cytometry+with+microfluidics+and+microfabrication.">The intersection of flow cytometry with microfluidics and microfabrication.</a> Lab Chip. 14, 1044-1059 (2014).</li><li>Grenvall, C., Antfolk, C., Bisgaard, C. Z., Laurell, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two-dimensional+acoustic+particle+focusing+enables+sheathless+chip+Coulter+counter+with+planar+electrode+configuration.">Two-dimensional acoustic particle focusing enables sheathless chip Coulter counter with planar electrode configuration.</a> Lab Chip. 14 (24), 4629-4637 (2014).</li><li>Au, A. K., Lee, W., Folch, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Mail-order+microfluidics:+evaluation+of+stereolithography+for+the+production+of+microfluidic+devices.">Mail-order microfluidics: evaluation of stereolithography for the production of microfluidic devices.</a> Lab Chip. 14 (7), 1294-1301 (2014).</li><li>Piyasena, M. E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multinode+acoustic+focusing+for+parallel+flow+cytometry.">Multinode acoustic focusing for parallel flow cytometry.</a> Anal Chem. 84 (4), 1831-1839 (2012).</li><li>Lenshof, A., Evander, M., Laurell, T., Nilsson, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acoustofluidics+5:+Building+microfluidic+acoustic+resonators.">Acoustofluidics 5: Building microfluidic acoustic resonators.</a> Lab Chip. 12 (4), 684-695 (2012).</li><li>Evander, M., Tenje, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Microfluidic+PMMA+interfaces+for+rectangular+glass+capillaries.">Microfluidic PMMA interfaces for rectangular glass capillaries.</a> J Micromech Microeng. 24 (2), 027003 (2014).</li></ol>

The authors declare that they have no competing financial interests.

Acoustophoresis offers a simple and rapid approach to precisely arrange microscopic entities within fluidic microchannels without the need of sheath fluids used in hydrodynamic focusing approaches.24 These devices provide several advantages over other methods of particle or cell manipulation (e.g., magnetophoresis,25,26 dielectrophoresis27 or inertial forcing28) due to their ability to process entities without high magnetic susceptibilities, electric polarizabilities or a narrow size dispersity. Furthermore, the focusing nodes of an acoustic standing wave can be positioned far from the source of excitation, which is something that is not possible by static magnetic or electric fields as per Earnshaw&#39;s theorem.29 An additional advantage is that acoustic devices can focus particles across a wide range of applied flow rates and independent of the flow direction, which is not possible in devices that rely on inertial forces for focusing,28 providing the means to efficiently transport particles or cells for enhanced particle inspection for applications such as flow cytometry and particle sizing.30,31 The ease of device fabrication and operation can directly allow for the implementation of similar devices for focusing, concentrating, fractionating and sorting objects suspended in fluids.32
We have shown that the primary radiation forces, which are the strongest forces produced by acoustic standing waves,1 can focus microparticles flowing through a microfluidic channel at flow rates exceeding 10 ml/hr for a single orifice design. For a fixed flow rate of 100 &#181;l/min, we show that our device can focus particles into a narrow streamline (i.e., 50 &#181;m across) without any sheath fluids at voltages as low as 20 V peak-to-peak, enabling a low-power method for the batchwise focusing of 10 million particles/min when processing densely concentrated solutions (e.g., 6 x 108 particles/ml), as an example. Furthermore, this throughput can be dramatically increased by fabricating multi-orifice acoustofluidic chips or channels that are actuated with higher harmonics to produce sets of parallel nodes.33
While the device shown herein only requires materials and methods used in conventional microfabrication, we emphasize that there are a handful of other techniques that can be used for constructing similar devices.19,34,35 The advantages of this approach include its simplicity as well as the durability of the final device.
The critical steps to the fabrication of these devices include photolithography to define the geometry of the microchannel, reactive ion etching to form the channel in the silicon and anodic bonding to fuse the silicon to a transparent &#34;lid&#34; for observation by fluorescence microscopy. All of these steps require clean room facilities to avoid the collection of dust or debris within the device. Once these steps are complete, however, bonding a PZT transducer and fluidic ports are relatively straightforward and can be performed outside of a clean room.
However, proper treatment of the device is essential for its longevity. This includes (1) incubating the device with passivating reagents (e.g., poly(ethylene glycol) silane) prior to each experiment to protect the channel from residue buildup and (2) flushing the device with detergents after each experiment. Buildup of debris may compromise the fidelity of the acoustic standing wave and may reduce the ability to efficiently focus particles or cells within the device. We also note that these devices are not well-suited for highly polydisperse samples or samples containing entities approaching half of the size of the standing wave.
Acoustofluidic devices provide enormous utility for a variety of applications spanning from colloidal assembly to cell separation and flow cytometry. The ability to process biological samples with precision at high flow rates can allow for the ability of increased throughputs by these microfluidic devices, while reducing costs from superfluous reagents, large sample volumes or bulky equipment for dispensing sheath fluids. The fabrication methods required to make acoustofluidic devices are straightforward and the procedures required for their operation are user-friendly. We hope these procedures will encourage the widespread development of similar devices to catalyze new areas of research for applications across materials science, biotechnology and medicine.

Acoustofluidic devices are used to exert directional forces on microscopic entities (e.g., particles or cells) for their concentration, alignment, assembly, confinement or separation within quiescent fluids or laminar flowstreams.1 Within this broad class of devices, forces can be generated from bulk acoustic standing waves, surface acoustic standing waves (SSAWs)2 or acoustic travelling waves.3 While we focus on the fabrication and operation of devices supporting bulk acoustic standing waves, devices supporting SSAWs have received much attention recently due to their ability to precisely manipulate cells along surfaces4 and rapidly sort cells in continuous flow channels.5 Devices supporting bulk acoustic standing waves, however, rearrange particles based on the mechanical vibrations of the walls of the device generated by a piezoelectric transducer, which excites the standing waves in microfluidic cavities at geometrically defined resonant frequencies. This enables the potential for generating higher pressure amplitudes compared to SSAW devices, and thus, faster acoustophoretic transport of microscopic entities.6
These standing waves consist of a spatially periodic set of pressure nodes and antinodes, which are fixed in position as the pressure oscillates in time. Particles respond to the standing waves by migrating to the pressure nodes or antinodes, depending on the mechanical properties of the particles relative to the fluid, and which are described by the acoustic contrast factor:
<img alt="Equation1" src="/files/ftp_upload/53861/53861equation1.jpg" />
where the variables &#961; and &#946; represent density and compressibility and the subscripts p and &#402; represent the suspended object (e.g., particle or cell) and the fluid, respectively.7 Entities that possess a positive acoustic contrast factor (i.e., &#632; &#62;0) migrate to the pressure node(s); whereas, entities that possess a negative acoustic contrast factor (i.e., &#632; &#60;0) migrate to the pressure antinodes.7 While the majority of synthetic materials (e.g., polystyrene beads) and cells exhibit positive acoustic contrast, elastomeric particles made from silicone-based materials,8 fatty molecules9 or other highly elastic constituents exhibit negative acoustic contrast in water. Elastomeric particles in acoustofluidic devices can be used to isolate small molecules10 and as means to confine synthetic particles11 or cells12 for the purposes of discriminate sorting.13
Acoustofluidic devices are usually manufactured from standard materials (e.g., silicon and glass) that have sufficient rigidity to support an acoustic standing wave. In many acoustofluidic devices (including the device shown herein), the mechanical waves are designed to resonate at the lowest harmonic mode, which consists of a half-wavelength standing wave spanning the width of the microchannel. This configuration has a pressure node at the center of the channel and pressure antinodes along the peripheries of the channel. It has been shown previously that these systems can be used for chip-based cytometry applications14-16 and applications ranging from the trapping of cells to the concentration of cells.17,18
We describe the process of fabrication, methods for use and representative performance capabilities of an acoustofluidic device that supports bulk acoustic standing waves. This device requires one photolithography step, one etching step and one fusing step to permanently bond a glass &#34;lid&#34; to the etched silicon substrate. We note that other acoustofluidic devices that support bulk acoustic standing waves can be fabricated from glass or quartz capillaries bound to piezoelectric transducers, which is described elsewhere.19,20 Silicon-based devices offer the advantages of robustness and control over the flow channel geometry, which together allow for numerous types of processing for samples containing suspensions of particles and cells. The devices are reusable provided they are properly cleaned between uses (i.e., by flushing the device with buffers and detergents).

<table border="0" cellpadding="0" cellspacing="0" width="516">
	<tbody>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">Silicon wafers</td>
			<td style="width:115px;">Addison Engineering, Inc.</td>
			<td style="width:93px;">3P1</td>
			<td style="width:163px;">6&#8221; mechanical grade silicon wafer &#60;111&#62;</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">AZ&#174; 9260 photoresist</td>
			<td style="width:115px;">MicroChemicals GmbH</td>
			<td style="width:93px;">AZ9260-Q</td>
			<td style="width:163px;">Positive photoresist</td>
		</tr>
		<tr height="47">
			<td height="47" style="height:47px;width:145px;">AZ&#174; 400K developer</td>
			<td style="width:115px;">MicroChemicals GmbH</td>
			<td style="width:93px;">AZ400K CONC-CS</td>
			<td style="width:163px;">Dilute 1 part AZ 400k in 4 parts deionized H2O</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">H2O2</td>
			<td style="width:115px;">Sigma Aldrich, Co.</td>
			<td style="width:93px;">216763</td>
			<td style="width:163px;">30 wt.% in H2O</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">H2SO4</td>
			<td style="width:115px;">Sigma Aldrich, Co.</td>
			<td style="width:93px;">320501</td>
			<td style="width:163px;">ACS reagent, 95.0-98.0%</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">1165 Photoresist Remover</td>
			<td style="width:115px;">Dow Chemical, Co.</td>
			<td style="width:93px;">DEM-10018073</td>
			<td style="width:163px;">1-methyl-2-pyrrolidinone based</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">Acetone</td>
			<td style="width:115px;">Sigma Aldrich, Co.</td>
			<td style="width:93px;">320110</td>
			<td style="width:163px;">ACS reagent, &#8805;99.5%</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">Isopropyl alcohol</td>
			<td style="width:115px;">Sigma Aldrich, Co.</td>
			<td style="width:93px;">W292907</td>
			<td style="width:163px;">&#8805;99.7%, FCC, FG</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">Methanol</td>
			<td style="width:115px;">Sigma Aldrich, Co.</td>
			<td style="width:93px;">322415</td>
			<td style="width:163px;">Anhydrous, 99.8%</td>
		</tr>
		<tr height="21">
			<td height="85" rowspan="4" style="height:85px;width:145px;">Borosilicate glass&#160; (Nexterion glass B)</td>
			<td rowspan="4" style="width:115px;">Schott AG&#160;</td>
			<td rowspan="4" style="width:93px;">2098576</td>
			<td style="width:163px;">Size: 120x60 &#177;0.1 mm, Thickness: 1 &#177;0.005 mm</td>
		</tr>
		<tr height="21">
			<td align="left" height="21" style="height:21px;width:163px;">&#160;
			<table cellpadding="0" cellspacing="0">
				<tbody>
					<tr>
						<td height="21" style="height:21px;width:163px;">0.1 mm</td>
					</tr>
				</tbody>
			</table>
			</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:163px;">Thickness: 1</td>
		</tr>
		<tr height="22">
			<td align="left" height="22" style="height:22px;width:163px;">&#160;
			<table cellpadding="0" cellspacing="0">
				<tbody>
					<tr>
						<td height="22" style="height:22px;width:163px;">0.005 mm</td>
					</tr>
				</tbody>
			</table>
			</td>
		</tr>
		<tr height="21">
			<td height="64" rowspan="3" style="height:64px;width:145px;">Drill bit for glass and ceramic&#160;</td>
			<td rowspan="3" style="width:115px;">McMaster-Carr, Inc.</td>
			<td rowspan="3" style="width:93px;">2954A1</td>
			<td style="width:163px;">Drill bit size: 1/8&#8221; Overall length: 2 3/16&#8221; Shank diameter: 7/64&#8221;</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:163px;">Overall length: 2 3/16&#8221;</td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:163px;">Shank diameter: 7/64&#8221;</td>
		</tr>
		<tr height="64">
			<td height="64" style="height:64px;width:145px;">Polydimethylsiloxane (PDMS) kit</td>
			<td style="width:115px;">Sigma Aldrich, Co.</td>
			<td style="width:93px;">761036</td>
			<td style="width:163px;">Dow Corning, Co.; Sylgard 184&#174;; 10 g clip-pack</td>
		</tr>
		<tr height="21">
			<td height="64" rowspan="3" style="height:64px;width:145px;">Biopsy punch&#160;&#160;</td>
			<td rowspan="3" style="width:115px;">Ted Pella, Inc.&#160;</td>
			<td rowspan="3" style="width:93px;">15078</td>
			<td style="width:163px;">Harris uni-core Tip ID: 3.0 mm&#160;Tip OD: 3.40 mm</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:163px;">Tip ID: 3.0 mm&#160;</td>
		</tr>
		<tr height="22">
			<td height="22" style="height:22px;width:163px;">Tip OD: 3.40 mm</td>
		</tr>
		<tr height="21">
			<td height="106" rowspan="4" style="height:106px;width:145px;">Lead zirconate titanate (PZT) transducer</td>
			<td rowspan="4" style="width:115px;">APC International, Ltd.</td>
			<td style="width:93px;">Custom order, (841 WFB)</td>
			<td style="width:163px;">Length: 30.0 mm, Width: 5.0mm, Freq.: 2.46 MHz, 2.0 mm end wrap for leads</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:93px;">(841 WFB)</td>
			<td style="width:163px;">Width: 5.0mm</td>
		</tr>
		<tr height="21">
			<td height="21" style="height:21px;width:93px;"></td>
			<td style="width:163px;">Freq.: 2.46 MHz</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:93px;"></td>
			<td style="width:163px;">2.0 mm end wrap for leads</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">Silicone tubing&#160;</td>
			<td style="width:115px;">Cole Parmer Instrument, Co.</td>
			<td style="width:93px;">07625-22</td>
			<td style="width:163px;">0.6 mm I.D.</td>
		</tr>
		<tr height="43">
			<td height="43" style="height:43px;width:145px;">Polystyrene beads</td>
			<td style="width:115px;">Thermo Fischer Scientific, Inc.</td>
			<td style="width:93px;">F-8836</td>
			<td style="width:163px;">10 &#181;m yellow-green fluorescence</td>
		</tr>
	</tbody>
</table>

fabrication and operation of acoustofluidic devices supporting bulk acoustic standing waves for sheathless focusing of particles

Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must be smaller than the incident wavelength of sound and the width of the fluidic channels are typically tens to hundreds of micrometers across, acoustofluidic devices typically use ultrasonic waves generated from a piezoelectric transducer pulsating at high frequencies (in the megahertz range). At characteristic frequencies that depend on the geometry of the device, it is possible to induce the formation of standing waves that can focus particles along desired fluidic streamlines within a bulk flow. Here, we describe a method for the fabrication of acoustophoretic devices from common materials and clean room equipment. We show representative results for the focusing of particles with positive or negative acoustic contrast factors, which move towards the pressure nodes or antinodes of the standing waves, respectively. These devices offer enormous practical utility for precisely positioning large numbers of microscopic entities (e.g., cells) in stationary or flowing fluids for applications ranging from cytometry to assembly.

We designed the acoustofluidic device to contain a trifurcating inlet, a main channel with a width of 300 &#181;m and a trifurcating outlet (Figure 1A-B). We note that we only used one inlet for all experiments in this study (i.e., to achieve sheathless focusing of particles via acoustic radiation forces) by blocking the other inlets with removable plugs. Following the procedures described above, we constructed a chip possessing a channel width of 313 &#181;m, with an error of &#8764;4% due to imperfections during the microfabrication process (Figure 1C-D). We operated the device at a driving frequency of 2.366 MHz to induce a half-wavelength harmonic standing wave.
We used a signal generator connected to a power amplifier to generate the high frequency sinusoidal waveform to actuate the PZT transducer. We used an oscilloscope to measure the peak-to-peak output voltage (Vpp) generated from the power amplifier to verify the fidelity of the signal shape and amplitude. Using a syringe pump, we first injected a suspension of green fluorescent polystyrene beads at a rate of 100 &#181;l/min without actuation of the PZT transducer as a negative control (Figure 2A). Next, we actuated the device at 2.366 MHz to form a half-wavelength standing wave across the width of the microchannel (Vpp = 40 V; Figure 2B). We found that these particles, which have a positive acoustic contrast factor, focused along the pressure node as expected.6 We also injected red fluorescent particles with a negative acoustic contrast factor (i.e., &#632; &#8776; &#8722;0.88, synthesized from a process described previously)8 to verify that our device could induce their concentration along the pressure antinodes (Figure 2C).
Finally, we explored the extent of focusing of particles with a positive acoustic contrast factor at a range of flow rates (i.e., 0 to 1,000 &#181;l/min as regulated by a syringe pump) and voltages (i.e., 0 to 50 Vpp). Videos comprised of 15 frames were collected for each condition. ImageJ software was used to sample five of the fluorescence intensity profile across the width of the microchannel. A numerical computing program was used to average the intensity profiles for each condition and to smooth the averaged data using an inline filtering program. As expected, the extent of particle focusing (i.e., as defined by the width of the fluorescence peak, corresponding to the width of the stream of particles) decreased with increasing flow rates (Figure 3A). We also found that the extent of particle focusing increased with increasing applied voltages (Figure 3B).
<img alt="Figure 1" src="/files/ftp_upload/53861/53861fig1.jpg" /> 
Figure 1: Acoustofluidic device supporting bulk acoustic standing waves. Schematic views of the top (A) and bottom (B) of a device comprised of an etched silicon substrate fused to a borosilicate glass &#34;lid&#34;, polydimethylsiloxane (PDMS) blocks connected to silicone tubing and a piezoelectric transducer soldered to wires glued to the bottom of the device. Photographs of the top (C) and bottom (D) of the device are also shown. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53861/53861fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" src="/files/ftp_upload/53861/53861fig2.jpg" /> 
Figure 2: Acoustic focusing of particles with positive and negative acoustic contrast factors. (A) Prior to actuation of the lead zirconate titanate (PZT) transducer, particles with a positive acoustic contrast factor (10 &#181;m, yellow-green polystyrene beads) flowing at 100 &#181;l/min occupied the width of the microchannel. (B) After the PZT transducer is actuated (Vpp = 40 V and&#160;&#402; = 2.366 MHz), the particles in (A) are shown to focus along the pressure node of the standing wave. (C) Particles with a negative acoustic contrast factor focused along the pressure antinodes of the standing wave in the absence of applied flow (Vpp = 40 V and &#402; = 2.366 MHz). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53861/53861fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" src="/files/ftp_upload/53861/53861fig3.jpg" /> 
Figure 3: Focusing performance of an acoustofluidic device. Fluorescence intensity plots of polystyrene beads (shown in Figure 2A-B) are shown for (A) various flow rates (ranging from 0 to 1,000 &#956;l/min) with a constant peak-to-peak voltage of 40 V and (B) various applied voltages (ranging from 0 to 50 Vpp) with a constant flow rate of 100 &#181;l/min. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53861/53861fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Fabrication and Operation of Acoustofluidic Devices Supporting Bulk Acoustic Standing Waves for Sheathless Focusing of Particles at JoVE.com

Fabrication and Operation of Acoustofluidic Devices Supporting Bulk Acoustic Standing Waves for Sheathless Focusing of Particles

Acoustofluidic devices use ultrasonic waves within microfluidic channels to manipulate, concentrate and isolate suspended micro and nanoscopic entities. This protocol describes the fabrication and operation of such a device supporting bulk acoustic standing waves to focus particles in a central streamline without the aid of sheath fluids.

Acoustophoresis refers to the displacement of suspended objects in response to directional forces from sound energy. Given that the suspended objects must ...

fabrication-operation-acoustofluidic-devices-supporting-bulk-acoustic

Research

JoVE Journal

Engineering

12.7K Views.  Duke University. Acoustofluidic devices use ultrasonic waves within microfluidic channels to manipulate, concentrate and isolate suspended micro and nanoscopic entities. This protocol describes the fabrication and operation of such a device supporting bulk acoustic standing waves to focus particles in a central streamline without the aid of sheath fluids.

Video: Fabrication and Operation of Acoustofluidic Devices Supporting Bulk Acoustic Standing Waves for Sheathless Focusing of Particles

Fabrication, Operation and Flow Visualization in Surface-acoustic-wave-driven Acoustic-counterflow Microfluidics

Surface acoustic waves (SAWs) can be used to drive liquids in portable microfluidic chips via the acoustic counterflow phenomenon. In this video we present the fabrication protocol for a multilayered SAW acoustic counterflow device. The device is fabricated starting from a lithium niobate (LN) substrate onto which two interdigital transducers (IDTs) and appropriate markers are patterned. A polydimethylsiloxane (PDMS) channel cast on an SU8 master mold is finally bonded on the patterned substrate. Following the fabrication procedure, we show the techniques that allow the characterization and operation of the acoustic counterflow device in order to pump fluids through the PDMS channel grid. We finally present the procedure to visualize liquid flow in the channels. The protocol is used to show on-chip fluid pumping under different flow regimes such as laminar flow and more complicated dynamics characterized by vortices and particle accumulation domains.

In this video we first describe fabrication and operation procedures of a surface acoustic wave (SAW) acoustic counterflow device. We then demonstrate an experimental setup that allows for both qualitative flow visualization and quantitative analysis of complex flows within the SAW pumping device.

Surface acoustic waves (SAWs) can be used to drive liquids in portable microfluidic chips via the acoustic counterflow phenomenon. In this video we ...

Fabrication of Gate-tunable Graphene Devices for Scanning Tunneling Microscopy Studies with Coulomb Impurities

Owing to its relativistic low-energy charge carriers, the interaction between graphene and various impurities leads to a wealth of new physics and degrees of freedom to control electronic devices. In particular, the behavior of graphene&#8217;s charge carriers in response to potentials from charged Coulomb impurities is predicted to differ significantly from that of most materials. Scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS) can provide detailed information on both the spatial and energy dependence of graphene&#39;s electronic structure in the presence of a charged impurity.&#160;The design of a hybrid impurity-graphene device, fabricated using controlled deposition of impurities onto a back-gated graphene surface, has enabled several novel methods for controllably tuning graphene&#8217;s electronic properties.1-8 Electrostatic gating enables control of the charge carrier density in graphene and the ability to reversibly tune the charge2 and/or molecular5 states of an impurity. This paper outlines the process of fabricating a gate-tunable graphene device decorated with individual Coulomb impurities for combined STM/STS studies.2-5 These studies provide valuable insights into the underlying physics, as well as signposts for designing hybrid graphene devices.

This paper details the fabrication process of a gate-tunable graphene device, decorated with Coulomb impurities for scanning tunneling microscopy studies. Mapping the spatially dependent electronic structure of graphene in the presence of charged impurities unveils the unique behavior of its relativistic charge carriers in response to a local Coulomb potential.

Owing to its relativistic low-energy charge carriers, the interaction between graphene and various impurities leads to a wealth of new physics and degrees ...

Fabrication and Operation of a Nano-Optical Conveyor Belt

The technique of using focused laser beams to trap and exert forces on small particles has enabled many pivotal discoveries in the nanoscale biological and physical sciences over the past few decades. The progress made in this field invites further study of even smaller systems and at a larger scale, with tools that could be distributed more easily and made more widely available. Unfortunately, the fundamental laws of diffraction limit the minimum size of the focal spot of a laser beam, which makes particles smaller than a half-wavelength in diameter hard to trap and generally prevents an operator from discriminating between particles which are closer together than one half-wavelength. This precludes the optical manipulation of many closely-spaced nanoparticles and&#160;limits the&#160;resolution of optical-mechanical systems. Furthermore, manipulation using focused beams requires beam-forming or steering optics, which can be very bulky and expensive. To address these limitations in the system scalability of conventional optical trapping our lab has devised an alternative technique which utilizes near-field optics to move particles across a chip. Instead of focusing laser beams in the far-field, the optical near field of plasmonic resonators produces the necessary local optical intensity enhancement to overcome the restrictions of diffraction and manipulate particles at higher resolution. Closely-spaced resonators produce strong optical traps which can be addressed to mediate the hand-off of particles from one to the next in a conveyor-belt-like fashion. Here, we describe how to design and produce a conveyor belt using a gold surface patterned with plasmonic C-shaped resonators and how to operate it with polarized laser light to achieve super-resolution nanoparticle manipulation and transport. The nano-optical conveyor belt chip can be produced using lithography techniques and easily packaged and distributed.

The scalability and resolution of conventional optical manipulation techniques are limited by diffraction. We circumvent the diffraction limit and describe a method of optically transporting nanoparticles across a chip using a gold surface patterned with a path of closely spaced C-shaped plasmonic resonators.

The technique of using focused laser beams to trap and exert forces on small particles has enabled many pivotal discoveries in the nanoscale biological ...

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

Polymer-based materials hold promise as low-cost, flexible efficient photovoltaic devices. Most laboratory efforts to achieve high performance devices have used devices prepared by spin coating, a process that is not amenable to large-scale fabrication. This mismatch in device fabrication makes it difficult to translate quantitative results obtained in the laboratory to the commercial level, making optimization difficult. Using a mini-slot die coater, this mismatch can be resolved by translating the commercial process to the laboratory and characterizing the structure formation in the active layer of the device in real time and in situ as films are coated onto a substrate. The evolution of the morphology was characterized under different conditions, allowing us to propose a mechanism by which the structures form and grow. This mini-slot die coater offers a simple, convenient, material efficient route by which the morphology in the active layer can be optimized under industrially relevant conditions. The goal of this protocol is to show experimental details of how a solar cell device is fabricated using a mini-slot die coater and technical details of running in situ structure characterization using the mini-slot die coater.

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

Here, we present a protocol to fabricate organic thin film solar cells using a mini-slot die coater and related in-line structure characterizations using synchrotron scattering techniques.

Polymer-based materials hold promise as low-cost, flexible efficient photovoltaic devices. Most laboratory efforts to achieve high performance devices ...

Fabrication of Fully Solution Processed Inorganic Nanocrystal Photovoltaic Devices

We demonstrate a method for the preparation of fully solution processed inorganic solar cells from a spin and spray coating deposition of nanocrystal inks. For the photoactive absorber layer, colloidal CdTe and CdSe nanocrystals (3-5 nm) are synthesized using an inert hot injection technique and cleaned with precipitations to remove excess starting reagents. Similarly, gold nanocrystals (3-5 nm) are synthesized under ambient conditions and dissolved in organic solvents. In addition, precursor solutions for transparent conductive indium tin oxide (ITO) films are prepared from solutions of indium and tin salts paired with a reactive oxidizer. Layer-by-layer, these solutions are deposited onto a glass substrate following annealing (200-400 &#176;C) to build the nanocrystal solar cell (glass/ITO/CdSe/CdTe/Au). Pre-annealing ligand exchange is required for CdSe and CdTe nanocrystals where films are dipped in NH4Cl:methanol to replace long-chain native ligands with small inorganic Cl- anions. NH4Cl(s) was found to act as a catalyst for the sintering reaction (as a non-toxic alternative to the conventional CdCl2(s) treatment) leading to grain growth (136&#177;39 nm) during heating. The thickness and roughness of the prepared films are characterized with SEM and optical profilometry. FTIR is used to determine the degree of ligand exchange prior to sintering, and XRD is used to verify the crystallinity and phase of each material. UV/Vis spectra show high visible light transmission through the ITO layer and a red shift in the absorbance of the cadmium chalcogenide nanocrystals after thermal annealing. Current-voltage curves of completed devices are measured under simulated one sun illumination. Small differences in deposition techniques and reagents employed during ligand exchange have been shown to have a profound influence on the device properties. Here, we examine the effects of chemical (sintering and ligand exchange agents) and physical treatments (solution concentration, spray-pressure, annealing time and annealing temperature) on photovoltaic device performance.

This protocol describes the synthesis and solution deposition of inorganic nanocrystals layer by layer to produce thin film electronics on non-conductive surfaces. Solvent-stabilized inks can produce complete photovoltaic devices on glass substrates via spin and spray coating following post-deposition ligand exchange and sintering.

We demonstrate a method for the preparation of fully solution processed inorganic solar cells from a spin and spray coating deposition of nanocrystal ...

Solvent Bonding for Fabrication of PMMA and COP Microfluidic Devices

Thermoplastic microfluidic devices offer many advantages over those made from silicone elastomers, but bonding procedures must be developed for each thermoplastic of interest. Solvent bonding is a simple and versatile method that can be used to fabricate devices from a variety of plastics. An appropriate solvent is added between two device layers to be bonded, and heat and pressure are applied to the device to facilitate the bonding. By using an appropriate combination of solvent, plastic, heat, and pressure, the device can be sealed with a high quality bond, characterized as having high bond coverage, bond strength, optical clarity, durability over time, and low deformation or damage to microfeature geometry. We describe the procedure for bonding devices made from two popular thermoplastics, poly(methyl-methacrylate) (PMMA), and cyclo-olefin polymer (COP), as well as a variety of methods to characterize the quality of the resulting bonds, and strategies to troubleshoot low quality bonds. These methods can be used to develop new solvent bonding protocols for other plastic-solvent systems.

Solvent bonding is a simple and versatile method for fabricating thermoplastic microfluidic devices with high quality bonds. We describe a protocol to achieve strong, optically clear bonds in PMMA and COP microfluidic devices that preserve microfeature details, by a judicious combination of pressure, temperature, an appropriate solvent, and device geometry.

Thermoplastic microfluidic devices offer many advantages over those made from silicone elastomers, but bonding procedures must be developed for each ...

Flow-assisted Dielectrophoresis: A Low Cost Method for the Fabrication of High Performance Solution-processable Nanowire Devices

Flow-assisted dielectrophoresis (DEP) is an efficient self-assembly method for the controllable and reproducible positioning, alignment, and selection of nanowires. DEP is used for nanowire analysis, characterization, and for solution-based fabrication of semiconducting devices. The method works by applying an alternating electric field between metallic electrodes. The nanowire formulation is then dropped onto the electrodes which are on an inclined surface to create a flow of the formulation using gravity. The nanowires then align along the gradient of the electric field and in the direction of the liquid flow. The frequency of the field can be adjusted to select nanowires with superior conductivity and lower trap density. 
In this work, flow-assisted DEP is used to create nanowire field effect transistors. Flow-assisted DEP has several advantages: it allows selection of nanowire electrical properties; control of nanowire length; placement of nanowires in specific areas; control of orientation of nanowires; and control of nanowire density in the device. 
The technique can be expanded to many other applications such as gas sensors and microwave switches. The technique is efficient, quick, reproducible, and it uses a minimal amount of dilute solution making it ideal for the testing of novel nanomaterials. Wafer scale assembly of nanowire devices can also be achieved using this technique, allowing large numbers of samples for testing and large-area electronic applications.

In this paper, flow assisted dielectrophoresis is demonstrated for the self-assembly of nanowire devices. The fabrication of a silicon nanowire field effect transistor is shown as an example.

Flow-assisted dielectrophoresis (DEP) is an efficient self-assembly method for the controllable and reproducible positioning, alignment, and selection of ...

Atmospheric Pressure Fabrication of Large-Sized Single-Layer Rectangular SnSe Flakes

Tin selenide (SnSe) belongs to the family of layered metal chalcogenide materials with a buckled structure like phosphorene, and has shown potential for applications in two-dimensional nanoelectronics devices. Although many methods to synthesize SnSe nanocrystals have been developed, a simple way to fabricate large-sized single-layer SnSe flakes remains a great challenge. Herein, we show the experimental method to directly grow large-sized single-layer rectangular SnSe flakes on commonly used SiO2/Si insulating substrates using a straightforward two-step fabrication method in an atmospheric pressure quartz tube furnace system. The single-layer rectangular SnSe flakes with an average thickness of ~6.8 &#197; and lateral dimensions of about 30 &#181;m &#215; 50 &#181;m were fabricated by a combination of vapor transport deposition technique and nitrogen etching route. We characterized the morphology, microstructure, and electrical properties of the rectangular SnSe flakes and obtained excellent crystallinity and good electronic properties. This article about the two-step fabrication method can help researchers grow other similar two-dimensional, large-sized, single-layer materials using an atmospheric pressure system.

A protocol is presented demonstrating a two-step fabrication technique to grow large-sized single-layer rectangular shaped SnSe flakes on low-cost SiO2/Si dielectrics wafers in an atmospheric pressure quartz tube furnace system.

Tin selenide (SnSe) belongs to the family of layered metal chalcogenide materials with a buckled structure like phosphorene, and has shown potential for ...

Generation of Size-controlled Poly (ethylene Glycol) Diacrylate Droplets via Semi-3-Dimensional Flow Focusing Microfluidic Devices

Uniform and size-controllable poly (ethylene glycol) diacrylate (PEGDA) droplets could be produced via the flow focusing process in a microfluidic device. This paper proposes a semi-three-dimensional (semi-3D) flow-focusing microfluidic chip for droplet formation. The polydimethylsiloxane (PDMS) chip was fabricated using the multi-layer soft lithography method. Hexadecane containing surfactant was used as the continuous phase, and PEGDA with the ultraviolet (UV) photo-initiator was the dispersed phase. Surfactants allowed the local surface tension to drop and formed a more cusped tip which promoted breaking into tiny micro-droplets. As the pressure of dispersed phase was constant, the size of droplets became smaller with increasing continuous phase pressure before dispersed phase flow was broken off. As a result, droplets with size variation from 1 &#181;m to 80 &#181;m in diameter could be selectively achieved by changing the pressure ratio in two inlet channels, and the average coefficient of variation was estimated to be below 7%. Furthermore, droplets could turn into micro-beads by UV exposure for photo-polymerization. Conjugating biomolecules on such micro-beads surface have many potential applications in the fields of biology and chemistry.

Generation of Size-controlled Poly ethylene Glycol Diacrylate Droplets via Semi-3-Dimensional Flow Focusing Microfluidic Devices

Here, we present a protocol to illustrate the fabrication processes and verifying experiments of a semi-three-dimensional (semi-3D) flow-focusing microfluidic chip for droplet formation.

Uniform and size-controllable poly (ethylene glycol) diacrylate (PEGDA) droplets could be produced via the flow focusing process in a microfluidic device. ...

Microparticle Manipulation by Standing Surface Acoustic Waves with Dual-frequency Excitations

We demonstrate a method for increasing the tuning ability of a standing surface acoustic wave (SSAW) for microparticles manipulation in a lab-on-a-chip (LOC) system. The simultaneous excitation of the fundamental frequency and its third harmonic, which is termed as dual-frequency excitation, to a pair of interdigital transducers (IDTs) could generate a new type of standing acoustic waves in a microfluidic channel. Varying the power and the phase in the dual-frequency excitation signals results in a reconfigurable field of the acoustic radiation force applied to the microparticles across the microchannel (e.g., the number and location of the pressure nodes and the microparticle concentrations at the corresponding pressure nodes). This article demonstrates that the motion time of the microparticle to only one pressure node can be reduced ~2-fold at the power ratio of the fundamental frequency greater than ~90%. In contrast, there are three pressure nodes in the microchannel if less than this threshold. Furthermore, adjusting the initial phase between the fundamental frequency and the third harmonic results in different motion rates of the three SSAW pressure nodes, as well as in the percentage of microparticles at each pressure node in the microchannel. There is a good agreement between the experimental observation and the numerical predictions. This novel excitation method can easily and non-invasively integrate into the LOC system, with a wide tenability and only a few changes to the experimental set-up.

A protocol for manipulating the microparticles in a microfluidic channel with a dual-frequency excitation is presented.

We demonstrate a method for increasing the tuning ability of a standing surface acoustic wave (SSAW) for microparticles manipulation in a lab-on-a-chip ...