This research work was sponsored by the National Key Basic Research Program of China (No.2015CB251303), and the National Natural Science Foundation of China (No. 51276005).

1. Experimental Setup
NOTE: The adsorption refrigeration system was composed of the adsorption bed, the evaporator, the condenser, the vacuum pump, and the solar trough collector (Figure 1). An automatic solar tracking device with a parabolic trough was manufactured and applied in the system to improve the efficiency of the solar collector. The automatic solar tracking trough was driven by the worm-gear device as shown in Figure 2. The device consisted of the stepper motor, the worm, the gear, the moving limit block, and the manual wheel. The dimensions of the worm-gear device were 21 x 80 cm2. The trough collector concentrated the solar rays onto the adsorbent bed, which was located along the focus line of the parabolic trough.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/55925/55925fig1v2.jpg" /> 
Figure 1: Experimental system for solar adsorption refrigeration. (Top) Schematic of the system; (bottom) Photograph of the experimental setup. The top panel presents the components of the experimental system, which involves the evaporator, the condenser, the vacuum pump,&#160;etc.&#160;The bottom panel displays the photograph of the assembled adsorption refrigeration system. In the system, the evaporator and the condenser is of the fin-tube structure, a kind of compact heat exchanger. The adsorption bed is reformed from a vacuum solar collector, which can capture solar energy effectively.&#160;<a href="//cloudfront-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/55925/55925fig1v2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/55925/55925fig2v2.jpg" /> 
Figure 2: The structure of the worm gear box. The worm gear box is the device that transforms the rotation of the stepper motor into the solar tracking movement of the parabolic trough. In addition to the stepper motor, the worm gear box also involves the reducer, the manual wheel, the worm shaft,&#160;etc.&#160;Pulling the manual/automatic switch handle to the left, gears 5a and 5b are disengaged. Thus, the trough can be manually controlled by rotating the hand wheel. Pulling the manual/automatic switch handle to the right, gears 5a and 5b are engaged together. Thus, it is controlled automatically by the stepper motor.
<ol>
	<li>Connect the tracking solar collector to the worm-wheel shaft by a welding method. Pass the rotation of the stepper motor to the solar collector by matching the gear and the worm. Fix the tubular adsorption bed together with the collector with a pair of pipe collars. 
	NOTE: Driven by the stepper motor, the system rotates daily from the east to the west to follow the solar movement automatically.</li>
	<li>Adjust the tilting angle of the trough to ground level, according to the variation of the solar altitude in different seasons. Determine the tilting angle &#946; of the trough by the local latitude &#934; and the solar declination &#948;, and the formula &#946; = &#934;&#160;- &#948;. Manually rotate the little wheel that is located at the bottom of the angle adjustment lever to regulate the tilting angle of the trough (the part of No. 13, Figure 1). 
	NOTE: In this way, the solar radiation is as normal as possible on the trough. The experimental system was located in the campus of Beijing University of Technology, at the latitude 39.89 &#176;N and longitude 116.38 &#176;E. The adsorption bed took a cylindrical form. It was reformed from a vacuum solar receiver of a tube (Figure 3).</li>
</ol>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/55925/55925fig3v2.jpg" /> 
Figure 3: Structure of the adsorption bed and the deployment of the temperature probe. (Top) Schematic of the bed structure; (bottom) The temperature probes and the mass transfer channel in the bed. The top panel shows the basic structure of the bed. The adsorbent material is put into the annular cavity between the solar-absorbing tube and the copper cooling channel. The solar rays penetrate the glass tube and fall onto the surface of the solar-absorbing tube. Then, by heat conduction, the solar energy is transferred to the adsorbent material inside the bed. The bottom panel shows the location of the temperature probes. These probes are used to monitor the temperature change of the bed during the adsorption/desorption process.&#160;<a href="//cloudfront-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/55925/55925fig3v2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<ol start="3">
	<li>To promote the capture of the solar energy, coat the solar-absorbing tube of the bed, (made of stainless steel with d = 64.5 mm) with a layer of black chrome deposit by the vacuum coating method. Please refer to the previously published literature about selective coating for more information about this technique13. Ensure that the solar absorption rate of the coating layer is 0.95, the infrared emissivity is 0.15, and the thickness of the coating layer is 0.08 mm. 
	NOTE: This coating layer helps to catch the solar radiation effectively but emits very slightly itself. As a result, the solar energy gets into the adsorption bed easily and is transformed to thermal enthalpy of the adsorbent effectively.</li>
	<li>Insert a copper tube (d = 20 mm) along the axis of the adsorption bed. Fix the copper tube to the bed with the flange (see Figure 3, top panel). The copper tube functions as the cooling channel of the bed during the adsorption process.</li>
	<li>Fill the adsorbent material in the annular cavity in the bed that is formed by the bed tube and the copper cooling channel. Use SAPO-34 zeolite as the adsorbent material, and water as the refrigerant. Put 3.171 kg of the SAPO-34 zeolite into the bed. The granular SAPO-34 zeolite is 5.7 mm in diameter.</li>
	<li>Deploy nine temperature probes in three cross-sections of the bed to monitor the temperature change of the bed during the adsorption/desorption process (Figure 3, bottom panel). Fix a probe at each small supporter that is seated on the copper cooling channel.</li>
	<li>Put probes 1 and 2 in section A-A near the inlet of the adsorption bed. Put probes 8 and 9 near the dead end of the bed. Fix the other probes at the middle B-B section (see Figure 3).</li>
	<li>Insert axially a mass-transferring channel of d = 10 mm into the bed. Ensure that the mass channel has the form of reticular tube, and is the same length of the adsorption bed (dbed = 64.5 mm). Extend the channel downwards from the inlet and make it stand in the right position with the extrusion force of the adsorbent material. The reticular tube helps the water vapor to enter the deep region of the bed quickly.</li>
</ol>
2. Experimental Method
NOTE: Adsorption refrigeration is based on the principle that the solid adsorbent material adsorbs the refrigerant vapor strongly at low temperature, while it desorbs the vapor at a higher temperature. Using heat as the driving impetus, the purpose of refrigeration is reached. The refrigeration cycle of the adsorption system involves mainly four steps, i.e., the solar heating-up process, the desorption process, the bed-cooling process, and the adsorption process. The desorption process starts once again after the adsorption process is completed. All the steps of the experiment are equally important because they are interrelated and influence each other interactively.
<ol>
	<li>Regulate the experimental setup by the following procedures to start the solar heating and desorption of the bed.
	<ol>
		<li>Turn the parabolic trough manually until it is facing due east before the experiment, so that the sunlight irradiates the parabolic trough collector normally at noon.</li>
		<li>Shut off all the valves that are connected to the adsorption bed and ensure the pressure of the bed and the pipe is below 800 Pa. Make it ready for solar heating.</li>
		<li>Switch on the controlling rig of the system when the sun light is parallel to the horizon line in the morning. Make the trough automatically rotate to trace the solar movement.</li>
		<li>Allow the adsorption-saturated bed to be heated by solar radiation under closed conditions. As a result, the bed temperature and the bed pressure will increase gradually.</li>
		<li>Monitor the bed pressure with the pressure gauge (Number 6 in Figure 1) until it is higher than the pressure value that corresponds to the condensation temperature of the environment. According to the thermodynamics, the condensation pressure of the water at 30 &#176;C is 4,246 Pa.</li>
	</ol>
	</li>
	<li>Start the desorption process. 
	&#8203;NOTE: In the desorption process, the condensation of water vapor occurs. The condensation temperature is determined by local weather conditions on the test day.
	<ol>
		<li>Open the valve that connects the bed and the condenser. Let water vapor flow into the condenser through the connecting pipe. As water vapor enters the condenser, the temperature of the condenser will rise gradually.</li>
		<li>At the same time, keep the solar heating to the adsorption bed, so that the bed pressure remains high enough to cause the desorption. Do not stop the solar heating until the process is completed.</li>
		<li>End the desorption process when the pressure of the bed is equal to the pressure of the condenser. Turn off the valve when the desorption process is over.</li>
	</ol>
	</li>
	<li>Cool down the bed before the adsorption process, as the bed is still in the state of high temperature after the desorption. The adsorbent material can largely adsorb only at low temperature.
	<ol>
		<li>To start the adsorption process, shield the adsorption bed with an aluminum foil sheet, so that the bed is cut off from the solar radiation.</li>
		<li>Close all the valves that connect the evaporator and the condenser.</li>
		<li>Open the circulating water-loop of the bed and cool down the adsorbent material. With the water continually circulating in the bed, the internal enthalpy is taken out and the bed pressure decreases correspondingly.</li>
		<li>End the cooling process when the bed pressure drops below the saturated vapor pressure at the evaporator&#39;s temperature. 
		NOTE: Be ready for the adsorption refrigeration process after the cooling down of the bed. Now the bed temperature is around the ambient air temperature, and the bed pressure has reached to the minimum level.</li>
		<li>Keep the circulating water-loop in a working state during the adsorption process. The adsorption is an exothermic process, and the generated heat needs to be discharged outside as soon as possible.</li>
		<li>Open the valve between the bed and the evaporator. Let the water vapor rush into the bed from the evaporator. 
		NOTE: The vapor reduction of the evaporator causes more water to vaporize, which results in the drastic decrease of the evaporator temperature. Consequentially, the evaporator absorbs heat from the water tank where the evaporator is seated, and a refrigeration effect is obtained.</li>
		<li>Keep the adsorption process going on, and record the change of the bed temperature and the bed pressure. 
		NOTE: During the adsorption process, the vapor pressure in the evaporator becomes lower and lower, but the bed temperature increases quickly.</li>
		<li>End the adsorption process when the bed pressure is equal to the evaporator pressure. Afterwards, the desorption process will follow again.</li>
	</ol>
	</li>
</ol>
3. Data Reduction Method
<ol>
	<li>Evaluate the performance of the refrigeration system based on the refrigeration capacity and the efficiency of the heat-to-cold transformation. 
	&#8203;NOTE: For the current system, the refrigeration capacity is calculated by the mass amount of the vaporized water and the temperature change of the evaporator itself.
	<ol>
		<li>To determine the total refrigeration capacity (Qref) of the system, calculate the sum of the enthalpy decrement of the chilled water in the tank, the metal evaporator, and the residual water in the evaporator after the adsorption as follows: 
		<img alt="Equation 1" src="/files/ftp_upload/55925/55925eq1.jpg" /> 
		where cp in Eq. (1) is the specific heat at constant pressure, and m denotes the mass. C is a correction factor to the refrigeration capacity of the evaporator considering the heat transfer between the water tank and the ambient environment, and it is assumed C = 1.15 according to the principle of heat transfer. The subscript w and e represents the water and the evaporator, respectively. In the equation mw,tan and mw,eva is the mass of the chilled water in the tank and the mass of the residual water in the evaporator, which corresponds to the temperature drop &#916;Tw and &#916;Te, respectively. 
		NOTE: The solar energy input to the bed is needed to evaluate the efficiency of the heat-to-cold transformation.</li>
		<li>Determine the solar energy input Qs as: 
		<img alt="Equation 2" src="/files/ftp_upload/55925/55925eq2.jpg" /> 
		where, Is,i (t) is the transient solar intensity recorded by the actinometer during the desorption process. The time interval &#916;t of the data acquisition to the Is,i (t) is 10 s. The aperture area of the parabolic trough Ap, the reflective efficiency of the trough surface &#961;, the transmittance of the tube glass &#964;, and the solar absorption coefficient of the coating surface &#945;, together with the parameters in Eq. (1), are all listed in Table 1.</li>
		<li>Based on the Qref and theQs obtained above, determine the COP of the refrigeration system as14: 
		<img alt="Equation 3" src="/files/ftp_upload/55925/55925eq3.jpg" /> 
		&#946;1 and &#946;2 are correction factors to the solar energy input Qs. &#946;1 is the correction factor of the non-parabolic degree of the trough, which takes into account the deformation of the trough because of the limitations of the manufacturing technique, and it is assumed &#946;1 = 0.85. &#946;2 is the correction factor of the real amount of obtained heat of the bed. Due to the smaller size of the metal bed tube than the outer glass tube, the real obtained heat amount is less than that reflected onto the glass tube. &#946;2 is decided by the ratio of the metal bed diameter D2 to the glass tube diameter D1. With D1 = 100 mm and D2 = 64.5 mm, it is calculated that &#946;2 = 0.645.</li>
		<li>Determine the specific cooling power of the bed by the parameters of the experiment as14: 
		<img alt="Equation 4" src="/files/ftp_upload/55925/55925eq4.jpg" /> 
		where ma is the mass of the adsorbent material and tads is the time duration of the adsorption process.</li>
	</ol>
	</li>
</ol>
<img alt="Table 1" src="/files/ftp_upload/55925/55925table1v2.jpg" /> 
Table 1: Values of the parameter in Eq. (1) and Eq. (2). The parameters that are involved in&#160;Eq. (1)&#160;and&#160;Eq. (2)&#160;are listed in this table. The parameters include cp, Ap,&#160;&#945;, etc.

<ol>
	<li>Hu, P., Yao, J. J., Chen, Z. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Analysis+for+composite+zeolite/foam+aluminum-water+mass+recovery+adsorption+refrigeration+system+driven+by+engine+exhaust+heat.">Analysis for composite zeolite/foam aluminum-water mass recovery adsorption refrigeration system driven by engine exhaust heat.</a> Energ Convers Manage. 50, 255-261 (2009).</li><li>Sutuki, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Application+of+adsorption+cooling+system+to+automobiles.">Application of adsorption cooling system to automobiles.</a> Heat Recov Syst CHP. 4 (13), 335-340 (1993).</li><li>Li, M., Wang, R. Z., Xu, Y. X., Wu, J. Y., Dieng, A. O. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experimental+study+on+dynamic+performance+analysis+of+a+flat-plate+solar+solid-adsorption+refrigeration+for+icemaker.">Experimental study on dynamic performance analysis of a flat-plate solar solid-adsorption refrigeration for icemaker.</a> Renew Energy. 27, 211-221 (2002).</li><li>Liu, Y. L., Wang, R. Z., Xia, Z. Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experimental+study+on+a+continuous+adsorption+water+chiller+with+novel+design.">Experimental study on a continuous adsorption water chiller with novel design.</a> Int J Refrig. 28 (2), 218-230 (2005).</li><li>Sumathy, K., Li, Z. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experiments+with+solar-powered+adsorption+ice-maker.">Experiments with solar-powered adsorption ice-maker.</a> Renew Energy. 16, 704-707 (1999).</li><li>Hadj Ammar, M. A., Benhaoua, B., Balghouthi, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simulation+of+tubular+adsorber+for+adsorption+refrigeration+system+powered+by+solar+energy+in+sub-Sahara+region+of+Algeria.">Simulation of tubular adsorber for adsorption refrigeration system powered by solar energy in sub-Sahara region of Algeria.</a> Energ Convers Manage. 106, 31-40 (2015).</li><li>Wang, R. Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experiment+on+a+continuous+heat+regenerative+adsorption+refrigerator+using+spiral+plate+heat+exchanger+as+adsorbers.">Experiment on a continuous heat regenerative adsorption refrigerator using spiral plate heat exchanger as adsorbers.</a> Appl Therm Eng. 18, 14-19 (1998).</li><li>Abu-Hamdeh, N. H., Alnefaie, K. A., Almitani, K. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+and+performance+characteristics+of+solar+adsorption+refrigeration+system+using+parabolic+trough+collector:+experimental+and+statistical+optimization+technique.">Design and performance characteristics of solar adsorption refrigeration system using parabolic trough collector: experimental and statistical optimization technique.</a> Energ Convers Manage. 74, 162-170 (2013).</li><li>El Fadar, A., Mimet, A., P&#233;rez-Garc&#237;a, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Study+of+an+adsorption+refrigeration+system+powered+by+parabolic+trough+collector+and+coupled+with+a+heat+pipe.">Study of an adsorption refrigeration system powered by parabolic trough collector and coupled with a heat pipe.</a> Renew Energy. 34, 2271-2279 (2009).</li><li>Restuccia, G., Freni, A., Russo, F., Vasta, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experimental+investigation+of+a+solid+adsorption+chiller+based+on+a+heat+exchanger+coated+with+hydrophobic+zeolite.">Experimental investigation of a solid adsorption chiller based on a heat exchanger coated with hydrophobic zeolite.</a> Appl Therm Eng. 25, 1419-1428 (2005).</li><li>Al Mers, A., Azzabakh, A., Mimet, A., El Kalkha, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optimal+design+study+of+cylindrical+finned+reactor+for+solar+adsorption+cooling+machine+working+with+activated-ammonia+pair.">Optimal design study of cylindrical finned reactor for solar adsorption cooling machine working with activated-ammonia pair.</a> Appl Therm Eng. 26 (16), 1866-1875 (2006).</li><li>Louajari, M., Mimet, A., Ouammi, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Study+of+the+effect+of+finned+tube+adsorber+on+the+performance+of+solar+driven+adsorption+cooling+machine+using+activated+carbon-ammonia+pair.">Study of the effect of finned tube adsorber on the performance of solar driven adsorption cooling machine using activated carbon-ammonia pair.</a> Appl Energ. 88, 690-698 (2011).</li><li>Mattox, D. M., Kominiak, G. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Deposition+of+semiconductor+films+with+high+solar+absorptivity.">Deposition of semiconductor films with high solar absorptivity.</a> J Vac Sci Technol. 12, 182-185 (1975).</li><li>Du, S. W., Li, X. H., Yuan, Z. X., Du, C. X., Wang, W. C., Liu, Z. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Performance+of+solar+adsorption+refrigeration+in+system+of+SAPO-34+and+ZSM-5+zeolite.">Performance of solar adsorption refrigeration in system of SAPO-34 and ZSM-5 zeolite.</a> Sol Energ. 138, 98-104 (2016).</li><li>Ron, M., Gruen, D., Mendelsohn, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preparation+and+properties+of+porous+metal+hydride+compacts.">Preparation and properties of porous metal hydride compacts.</a> J. Less- Common Metals. 74 (2), 445-448 (1980).</li><li>Liu, Z. Q., Wu, F., Tan, Z. H., Chen, S., Wang, G. Q. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+experimental+study+of+thermal+conductivity+enhancement+on+solid+adsorption+refrigeration.">An experimental study of thermal conductivity enhancement on solid adsorption refrigeration.</a> Mater Rev. 15 (12), 61-63 (2001).</li><li>Gordeeva, L. G., Freni, A., Restuccia, G., Aristov, Y. I. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adsorptive+air+conditioning+systems+driven+by+low+temperature+energy+sources:+choice+of+the+working+pairs.">Adsorptive air conditioning systems driven by low temperature energy sources: choice of the working pairs.</a> J Chem Eng Jpn. 40 (13), 1287-1291 (2007).</li><li>Kakiuchi, H., Shimooka, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Water+vapor+adsorbent+FAM-Z02+and+its+applicability+to+adsorption+heat+pump.">Water vapor adsorbent FAM-Z02 and its applicability to adsorption heat pump.</a> Kagaku Kogaku Ronbun, Jpn. 31 (4), 273-277 (2005).</li><li>Li, X. H., Hou, X. H., Zhang, X., Yuan, Z. X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+review+on+development+of+adsorption+cooling-Novel+beds+and+advanced+cycles.">A review on development of adsorption cooling-Novel beds and advanced cycles.</a> Energ Convers Manage. 94, 221-232 (2015).</li></ol>

The authors have nothing to disclose.

As a thermodynamic system, the performance of a solar adsorption refrigeration device depends on the optimum design and the proper operation of the system. Both the heat supply and the cooling method of the bed are important to guarantee the system works well. Water cooling is preferred to air cooling because of the high strength of convection heat transfer of water. The poor conductivity of the adsorbent material has usually determined the limited heat transfer rate of the bed. To improve the heat transfer of the bed, many measurements were considered such as the enhancement structure of the internally-inserted fins.19 Silica gel is another kind of popular adsorbent material. If a silica gel is used in the solar adsorption system, the desorption temperature of the bed must be limited to less than 95 &#176;C, so that the silica gel will not become dehydrated and lose activity.
Like most renewable energy systems, the current adsorption refrigeration system has some shortcomings in terms of engineering applications. The notable problem is the intermittent work of the system. With the intrinsic nature of the heating-up and cooling-down, the adsorption system can&#39;t supply cold power continually as a single bed is used. To solve this problem some researchers considered a conjugated two bed system, in which the technique of regenerative heat and mass transfer could be applied. Such systems can become rather complex but the performance improvement was often quite unsatisfactory. Another point that needs to be considered is the weather condition effect. For bad weather days, there will not enough solar energy supply to the system. In such a situation, some spare heat source needs to be ready so that the system can continue to work.
As a green energy technology, the solar adsorption refrigeration system has attracted much attention in the past decade. The use of solar energy avoids the consumption of fossil fuel and effectively reduces the air pollution. In addition, such a system has no rotating component, no noise, and can be deployed flexibly. Though the efficiency of the system is not comparable to conventional refrigeration systems that use vapor compression or ammonia absorption, the abundance of solar energy presents a potential significance for luminance in the future. For a system that consumes electricity or fuel, the efficiency of performance is very important because of operation costs. In contrast, solar energy is free and the system is still beneficial even if the COP is not very high.
We are not sure how quickly solar adsorption technologies may replace conventional refrigeration systems in large scale, because there are some aspects of this technique that need further improvement. A couple years ago, it was reported that the Tokyo Gas Corporation in Japan put forward a commercial type of adsorption refrigerator that was driven by industrial waste heat. With developments in the global economy and technology, the technique of the solar adsorption refrigeration may first find its application in the remote rural areas where the climate is hot in most time of the year.
The operation of this system involves four critical steps. According to the time sequence, they are: the pre-heating of the bed under closed conditions; the desorption process with the bed temperature increasing further; the cooling down of the bed by re-circulating water or an air stream; and the adsorption process that generates the refrigeration effect.

With the ozone-depletion problem of traditional vapor compressed refrigeration growing more serious, substituting traditional refrigeration with green technology has become a hot topic in recent years. Among those green technologies, the solar adsorption refrigeration has attracted much of the attention of researchers. Driven by low-grade thermal energy, the adsorption refrigeration system has the advantages of being environmentally friendly, small, and flexible. This adsorption system can also be driven with non-solar energy, for instance by waste heat discharged from thermal equipment or by engine exhaust gases from vehicles, as mentioned by Hu et al.1
In an adsorption cooling system, the adsorption bed is the key component. Its work directly affects the performance of the whole system. Therefore, the design of the adsorption bed is the most important issue as pointed out by Sutuki.2 A decade ago, the flat bed was mostly used in the adsorption cooling system.3,4,5 Without any solar concentrating device, the flat bed temperature was usually low and hence the COP of the system was unsatisfactory. In contrast, the tubular adsorption bed improved the COP. It was reported that the COP could reach 0.21 in sub-Sahara region by Hadj Ammar et al.6 Furthermore, Wang et al.7 developed a spiral plate adsorber that was distinguished by the characteristic of continuous heat regeneration. The novel design of the adsorption bed shortened the cycle time of the system. Abu-Hamdeh&#160;et al.8 reported their study on the solar adsorption refrigeration system with a parabolic trough collector. Their test results showed the COP of the system varied from 0.18 to 0.20. El Fadar et al.9 studied an adsorption refrigeration system that was coupled with a heat pipe and powered by parabolic trough collector, which showed an optimum COP of 0.18.
To enhance the heat transfer of the tubular bed, some finned tube adsorbers were considered and the effect of the enhancement was examined. An innovative bed that took the form of the shell and tube heat exchanger was presented by Restuccia et al.10. The internal finned tube was coated with a zeolite layer so that the contact transfer resistance of heat/mass between the metal surface and the adsorbent material could be reduced. The system produced an output of 30-60 W/kg of specific cooling power in the cycling time of 15-20 s. Al Mers et al.11demonstrated that the enhanced adsorber with 5-6 fins could significantly reduce the heat loss of the adsorber to ambiance and thereby improving the COP by 45%. The effect of a finned tube adsorber on the performance of the solar driven system was also studied by Louajari et al.12. Using activated carbon-ammonia as the working pair, they showed that the cycling mass transfer in the adsorber with fins was greater than the one without fins.
In the current study, we experimentally studied an improved solar adsorption refrigeration system, in which a solar tracking parabolic trough collector was applied and an internal cooling tunnel was deployed. With the SAPO-34/ZSM-5 zeolite and the water vapor as the working pair, the system showed interesting characteristics in terms of thermodynamics and refrigeration. The experimental methodology as well as the typical test results will be presented and discussed in this report.

<table>
	<tbody>
		<tr>
			<td>evaporator</td>
			<td>home-made</td>
			<td></td>
			<td>finned heat exchange</td>
		</tr>
		<tr>
			<td>condenser</td>
			<td>home-made</td>
			<td></td>
			<td>finned heat exchange</td>
		</tr>
		<tr>
			<td>evaporator water tank</td>
			<td>home-made</td>
			<td></td>
			<td>volume:9L</td>
		</tr>
		<tr>
			<td>condenser water tank</td>
			<td>home-made</td>
			<td></td>
			<td>volume:9L</td>
		</tr>
		<tr>
			<td>vacuum pump</td>
			<td>Beijing Jing Rui Ze Xiang Instrument Co. Ltd.</td>
			<td></td>
			<td>rotation speed:1400 motor pover:370W</td>
		</tr>
		<tr>
			<td>condenser pressure sensor</td>
			<td>Beijing Li Nuo Tian Sheng Instrument Co. Ltd.</td>
			<td>16P2623</td>
			<td>maximum:2200Pa</td>
		</tr>
		<tr>
			<td>bed pressure sensor</td>
			<td>Beijing Li Nuo Tian Sheng Instrument Co. Ltd.</td>
			<td></td>
			<td>maximum:2200Pa</td>
		</tr>
		<tr>
			<td>adsorption bed</td>
			<td>home-made</td>
			<td></td>
			<td>cylundrical glass tube</td>
		</tr>
		<tr>
			<td>parabolic trough</td>
			<td>home-made</td>
			<td></td>
			<td>high reflective aluminum sheet</td>
		</tr>
		<tr>
			<td>water pump</td>
			<td>home-made</td>
			<td></td>
			<td>motor pover:250W, water head:8m</td>
		</tr>
		<tr>
			<td>water tank</td>
			<td>home-made</td>
			<td></td>
			<td>volume:500L</td>
		</tr>
		<tr>
			<td>DRT-2-2 direct solar actinometer</td>
			<td>Beijing Tian Yu De Technology Co. Ltd.</td>
			<td>03140132</td>
			<td>sensitivity:13.257&#956;V/W&#8226;m2</td>
		</tr>
		<tr>
			<td>TBQ-2 solar pyranometer</td>
			<td>Jinzhou Sunshine Technology Development Co., Ltd., China</td>
			<td>209079</td>
			<td>sensitivity:12.733&#956;V/W&#8226;m2</td>
		</tr>
		<tr>
			<td>SAPO-34 zeolite</td>
			<td>Langfang Peng Cai Co., Ltd., China</td>
			<td></td>
			<td>20mm in length and 2.2mm in diameter</td>
		</tr>
		<tr>
			<td>ZSM-5 zeolite</td>
			<td>Langfang Peng Cai Co., Ltd., China</td>
			<td></td>
			<td>5.7mm in diameter</td>
		</tr>
	</tbody>
</table>

experimental system of solar adsorption refrigeration with concentrated collector

To improve the performance of solar adsorption refrigeration, an experimental system with a solar concentration collector was set up and investigated. The main components of the system were the adsorbent bed, the condenser, the evaporator, the cooling sub-system, and the solar collector. In the first step of the experiment, the vapor-saturated bed was heated by the solar radiation under closed conditions, which caused the bed temperature and pressure to increase. When the bed pressure became high enough, the bed was switched to connect to the condenser, thus water vapor flowed continually from the bed to the condenser to be liquefied. Next, the bed needed to cool down after the desorption. In the solar-shielded condition, achieved by aluminum foil, the circulating water loop was opened to the bed. With the water continually circulating in the bed, the stored heat in the bed was took out and the bed pressure decreased accordingly. When the bed pressure dropped below the saturation pressure at the evaporation temperature, the valve to the evaporator was opened. A mass of water vapor rushed into the bed and was adsorbed by the zeolite material. With the massive vaporization of the water in the evaporator, the refrigeration effect was generated finally. The experimental result has revealed that both the COP (coefficient of the performance of the system) and the SCP (specific cooling power of the system) of the SAPO-34 zeolite was greater than that of the ZSM-5 zeolite, no matter whether the adsorption time was longer or shorter. The system of the SAPO-34 zeolite generated a maximum COP of 0.169.

Mass transfer characteristic of the bed through the adsorption process 
The adsorption bed is always the most important component in an adsorption refrigeration system, and the heat and mass transfer characteristic are the main factors affecting the performance of the whole system. By analyzing the recorded temperature change in the cross sections as shown in Figure 3(bottom panel),&#160;it is possible to know the heat and mass transfer features of the bed. Figure 4 shows the dynamic change of the bed temperature during the adsorption process. The figure illustrates that the mass transfer ability of the SAPO-34 zeolite is good, for the adsorption of the points at different sections start almost the same time. If the mass transfer resistance of the bed is low, the bed may reach the adsorption equilibrium within a short time, and the adsorbent material in the bed will be fully employed. With the strongly cooling function of the circulating water convection, the temperature shooting-up was restrained effectively after about 400-600 s of the adsorption, except for time-point 9. In contrast, for a natural air cooling method, the bed temperature would decrease relatively slowly. The related experimental result has been discussed thoroughly in Du et al.14 The meager cooling effect of air flow frustrated the heat discharge of the bed, and then impacted the cycle performance of the adsorption refrigeration system. In comparison, water cooling was much better for the system.
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/55925/55925fig4v2.jpg" /> 
Figure 4: Temperature change of the bed in the adsorption process for SAPO-34 zeolite. This figure presents the temperature change of the bed in the adsorption process. Through the variation of the temperature, we can analyze the characteristics of the mass transfer of the bed. The response rate of the temperature reflects the adsorption rate of the material in the bed.
Heat transfer characteristic of the bed through the desorption process 
The adsorption process is a coupled heat and mass transfer phenomenon. The desorption/adsorption of the adsorbent is highly related to the temperature change of the bed. Nevertheless, the heat transfer characteristic of the bed is not only determined by the thermal properties of the adsorbent itself, but also by the bed structure. We tend to choose a material with both a strong adsorption ability and high conductivity. But unfortunately, quite often these qualities are in conflict. A porous material with good adsorption usually exhibits poor conductivity. Many factors (e.g., the molecular structure, the processing method, the particle size, etc.) can impact the thermal properties of the adsorbent15,16. Figure 5 shows the average temperature change of the bed in the desorption process for the SAPO-34 and ZSM-5 zeolite. To facilitate the comparison, the recorded solar intensity in the test campaign is also presented. Although the solar intensity was nearly the same for the two zeolites, the increment of temperature was quite different. For the ZSM-5 zeolite, the temperature was rising over 32 &#176;C, while for the SAPO-34 it was only 17 &#176;C. This result revealed that the heat transfer ability of the ZSM-5 zeolite was better than that of the SAPO-34 zeolite. The mass transfer between the adsorbent and the vapor is the most important process, but only with the support of the heat transfer can a good mass transfer be realized.
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/55925/55925fig5v2.jpg" /> 
Figure 5: The change of the average temperature of the bed during the desorption process. This figure shows the difference in the heat transfer between the SAPO-34 zeolite and the ZSM-5 zeolite. During the 600 s desorption time, the increment of the temperature for the ZSM-5 zeolite and SAPO-34 zeolite was quite different. For the ZSM-5 zeolite, the temperature increase was 32.52 &#176;C, while for the SAPO-34 zeolite the increase was only 17.02 &#176;C. At the same solar-heating condition, the larger temperature increment of the ZSM-5 zeolite indicates its superiority of heat transfer relative to SAPO-34 zeolite.
The desorption characteristic of the bed 
In general, the output of the refrigeration power for an adsorption system is determined by the adsorbent characteristic and the heat transfer rate of the bed. Usually, the time for the desorption process is longer than the time for the adsorption process. It is essential to know the characteristics of the heat transfer in the bed during the desorption. Here the index of the desorption degree E(t) is used to evaluate the completeness of the desorption of the bed. E(t) is defined as the ratio between the desorbed amount of refrigerant vapor, from the beginning to time t, and the total amount of the vapor uptake in the adsorption process.
With the experimental data, the E(t) of the bed at different desorption times can be obtained. Firstly, it is shown that the desorption degree was improved to some extent as the bed temperature increased. For the SAPO-34 zeolite system, the E(t) increased from 54.9% at t = 1 h to 69.3% at t = 2 h. On the other hand, at the same desorption time, the ZSM-5 system showed a worse desorption effect than the SAPO-34 system.14 Although the bed temperature of the SAPO-34 was comparatively lower, as previously discussed regarding Figure 5, its desorption degree was better. This tells us that SAPO-34 zeolite is more suitable to use as the adsorbent material. This feature of SAPO-34 zeoilite was also emphasized by Gordeeva et al.17
The refrigeration capacity of the system 
The refrigeration capacity of the adsorption system is basically reflected by the temperature decrease of the water tank. The test results for the tank temperature are presented in Figure 6. The tank temperature changed with time in a nonlinear way. It decreased quickly within the first 600 s of the adsorption time, and then the temperature decrease slowed down. In comparison to the two temperature profiles of the SAPO-34 and the ZSM-5 zeolite, it is known that the refrigeration capacity of the two zeolites was rather different. The temperature decrement of the water tank directly reflected the refrigeration capacity of the system. Obviously, the temperature drop for the SAPO-34 system was much greater than that for the ZSM-5 system. With better desorption characteristics as mentioned above, the SAPO-34 zeolite exhibited a higher refrigeration capacity than the ZSM-5 zeolite. This identification is consistent with the conclusion of Gordeeva et al.16 and Kakiuchi et al.18
<img alt="Figure 6" class="xfigimg" src="/files/ftp_upload/55925/55925fig6v2.jpg" /> 
Figure 6: The temperature variation of the chilled water tank. In general, the temperature variation of the chilled water in the evaporator tank was not linear. For the SAPO-34 zeolite, it declined quickly within the first 600 s and then the decline slowed down. In contrast, the temperature change of the ZSM-5 zeolite was relatively smooth. This reflected the feature that the refrigeration power output declined with time. The two curves also revealed the performance difference of SAPO-34 and ZSM-5 zeolite.
The performance of the system is evaluated by the index of COP and SCP that is determined by Eq. (3) and Eq. (4), respectively, and the results are shown in Table 2. According to the nonlinear change of the temperature in Figure 6, two sets of data for the adsorption time tads = 600 s and tads = 1,800 s are presented. For either case in the table, the Qref within the first 600 s takes a proportion of more than two thirds of the total refrigeration capacity of the 1,800 s adsorption time. Obviously, the SCP for tads = 600 s is much higher than that for tads = 1,800 s, however the COP results run contrary to these results. The best COP in Table 2 has reached 0.169. Error analysis was conducted and revealed the uncertainty of the COP was between 6.2&#8211;9.4% corresponding to different test campaigns. It needs to be mentioned that the maximum COP here is in the comparative range of the result by Abu-Hamdeh et al.8 Their system of parabolic trough collector generated a COP of 0.18-0.20. The SCP index reflects the specific power output of the refrigeration capacity of the bed. A higher SCP implies that a higher refrigeration power is generated by a unit of adsorbent mass. The analyzed results have demonstrated that both the COP and the SCP of the SAPO-34 were superior to that of the ZSM-5, no matter if the adsorption time was longer or shorter.
<img alt="Table 2" src="/files/ftp_upload/55925/55925table2v2.jpg" /> 
Table 2: Comparison of the refrigeration capacity of ZSM-5 and SAPO-34 zeolite. For comparison, here we present the comprehensive performance of the adsorption refrigeration of SAPO-34 and ZSM-5 zeolite. Either by the SCP index or by the COP index, the SAPO-34 system shows its superiority to the ZSM-5 system.

Watch this Scientific Journal Video about Experimental System of Solar Adsorption Refrigeration with Concentrated Collector at JoVE.com

Experimental System of Solar Adsorption Refrigeration with Concentrated Collector

With solar energy as the driving force, a novel adsorption refrigeration system has been developed and experimentally investigated. Water vapor and zeolite formed the working pair of the adsorption system. This manuscript describes the setup of the experimental rig, the operation procedure, and the important results.

To improve the performance of solar adsorption refrigeration, an experimental system with a solar concentration collector was set up and investigated. The ...

experimental-system-solar-adsorption-refrigeration-with-concentrated

Nanyang Technological University

Research

Education

JoVE Core

JoVE Journal

Physics

Environment

Unit 1

The Second Law of Thermodynamics

SCIENTISTS IN ACTION

14.4K 조회수.  Beijing University of Technology. With solar energy as the driving force, a novel adsorption refrigeration system has been developed and experimentally investigated. Water vapor and zeolite formed the working pair of the adsorption system. This manuscript describes the setup of the experimental rig, the operation procedure, and the important results.

비디오: Experimental System of Solar Adsorption Refrigeration with Concentrated Collector

Experimental Protocol for Manipulating Plant-induced Soil Heterogeneity

Coexistence theory has often treated environmental heterogeneity as being independent of the community composition; however biotic feedbacks such as plant-soil feedbacks (PSF) have large effects on plant performance, and create environmental heterogeneity that depends on the community composition. Understanding the importance of PSF for plant community assembly necessitates understanding of the role of heterogeneity in PSF, in addition to mean PSF effects. Here, we describe a protocol for manipulating plant-induced soil heterogeneity. Two example experiments are presented: (1) a field experiment with a 6-patch grid of soils to measure plant population responses and (2) a greenhouse experiment with 2-patch soils to measure individual plant responses. Soils can be collected from the zone of root influence (soils from the rhizosphere and directly adjacent to the rhizosphere) of plants in the field from conspecific and heterospecific plant species. Replicate collections are used to avoid pseudoreplicating soil samples. These soils are then placed into separate patches for heterogeneous treatments or mixed for a homogenized treatment. Care should be taken to ensure that heterogeneous and homogenized treatments experience the same degree of soil disturbance. Plants can then be placed in these soil treatments to determine the effect of plant-induced soil heterogeneity on plant performance. We demonstrate that plant-induced heterogeneity results in different outcomes than predicted by traditional coexistence models, perhaps because of the dynamic nature of these feedbacks. Theory that incorporates environmental heterogeneity influenced by the assembling community and additional empirical work is needed to determine when heterogeneity intrinsic to the assembling community will result in different assembly outcomes compared with heterogeneity extrinsic to the community composition.

Understanding the role of environmental heterogeneity in species coexistence has typically focused on types of heterogeneity that are extrinsic to the community&#8217;s species composition. We provide novel detailed methods for creating soil heterogeneity treatments using soils subject to plant-soil feedback conditioning, or heterogeneity intrinsic to the community composition.

조작 식물에 의한 토양의 이질성에 대한 실험 프로토콜

Coexistence theory has often treated environmental heterogeneity as being independent of the community composition; however biotic feedbacks such as ...

연구

환경과학

Experimental Protocol for Biodiesel Production with Isolation of Alkenones as Coproducts from Commercial Isochrysis Algal Biomass

The need to replace petroleum fuels with alternatives from renewable and more environmentally sustainable sources is of growing importance. Biomass-derived biofuels have gained considerable attention in this regard, however first generation biofuels from edible crops like corn ethanol or soybean biodiesel have generally fallen out of favor. There is thus great interest in the development of methods for the production of liquid fuels from domestic and superior non-edible sources. Here we describe a detailed procedure for the production of a purified biodiesel from the marine microalgae Isochrysis. Additionally, a unique suite of lipids known as polyunsaturated long-chain alkenones are isolated in parallel as potentially valuable coproducts to offset the cost of biodiesel production. Multi-kilogram quantities of Isochrysis are purchased from two commercial sources, one as a wet paste (80% water) that is first dried prior to processing, and the other a dry milled powder (95% dry). Lipids are extracted with hexanes in a Soxhlet apparatus to produce an algal oil (&#34;hexane algal oil&#34;) containing both traditional fats (i.e., triglycerides, 46-60% w/w) and alkenones (16-25% w/w). Saponification of the triglycerides in the algal oil allows for separation of the resulting free fatty acids (FFAs) from alkenone-containing neutral lipids. FFAs are then converted to biodiesel (i.e., fatty acid methyl esters, FAMEs) by acid-catalyzed esterification while alkenones are isolated and purified from the neutral lipids by crystallization. We demonstrate that biodiesel from both commercial Isochrysis biomasses have similar but not identical FAME profiles, characterized by elevated polyunsaturated fatty acid contents (approximately 40% w/w). Yields of biodiesel were consistently higher when starting from the Isochrysis wet paste (12% w/w vs. 7% w/w), which can be traced to lower amounts of hexane algal oil obtained from the powdered Isochrysis product.

Experimental Protocol for Biodiesel Production with Isolation of Alkenones as Coproducts from Commercial Isochrysis Algal Biomass

Detailed methods are presented for the production of biodiesel along with the co-isolation of alkenones as valuable coproducts from commercial Isochrysis microalgae.

상업에서 로서도으로 Alkenones의 분리와 바이오 디젤 생산을위한 실험 프로토콜<em&gt; 이소 크리 시스 속</em&gt; 해조 바이오 매스

The need to replace petroleum fuels with alternatives from renewable and more environmentally sustainable sources is of growing importance. ...

Experimental Protocol for Detecting Cyanobacteria in Liquid and Solid Samples with an Antibody Microarray Chip

Global warming and eutrophication make some aquatic ecosystems behave as true bioreactors that trigger rapid and massive cyanobacterial growth; this has relevant health and economic consequences. Many cyanobacterial strains are toxin producers, and only a few cells are necessary to induce irreparable damage to the environment. Therefore, water-body authorities and administrations require rapid and efficient early-warning systems providing reliable data to support their preventive or curative decisions. This manuscript reports an experimental protocol for the in-field detection of toxin-producing cyanobacterial strains by using an antibody microarray chip with 17 antibodies (Abs) with taxonomic resolution (CYANOCHIP). Here, a multiplex fluorescent sandwich microarray immunoassay (FSMI) for the simultaneous monitoring of 17 cyanobacterial strains frequently found blooming in freshwater ecosystems, some of them toxin producers, is described. A microarray with multiple identical replicates (up to 24) of the CYANOCHIP was printed onto a single microscope slide to simultaneously test a similar number of samples. Liquid samples can be tested either by direct incubation with the antibodies (Abs) or after cell concentration by filtration through a 1- to 3-&#956;m filter. Solid samples, such as sediments and ground rocks, are first homogenized and dispersed by a hand-held ultrasonicator in an incubation buffer. They are then filtered (5 - 20 &#956;m) to remove the coarse material, and the filtrate is incubated with Abs. Immunoreactions are revealed by a final incubation with a mixture of the 17 fluorescence-labeled Abs and are read by a portable fluorescence detector. The whole process takes around 3 h, most of it corresponding to two 1-h periods of incubation. The output is an image, where bright spots correspond to the positive detection of cyanobacterial markers.

Experimental Protocol for Detecting Cyanobacteria in Liquid and Solid Samples with an Antibody Microarray Chip

The presence of cyanobacterial toxins in fresh water reservoirs for human consumption is a major concern for water management authorities. To evaluate the risk of water contamination, this article describes an protocol for the in-field detection of cyanobacterial strains in liquid and solid samples by using an antibody microarray chip.

검출 실험 프로토콜<em&gt; 시아 노 박테리아</em&gt; 항체 마이크로 어레이 칩과 액체 및 고체 시료에

Global warming and eutrophication make some aquatic ecosystems behave as true bioreactors that trigger rapid and massive cyanobacterial growth; this has ...

Measuring and Mapping Patterns of Soil Erosion and Deposition Related to Soil Carbonate Concentrations Under Agricultural Management

Spatial patterns of soil erosion and deposition can be inferred from differences in ground elevation mapped at appropriate time increments. Such changes in elevation are related to changes in near-surface soil carbonate (CaCO3) profiles. The objective is to describe a simple conceptual model and detailed protocol for repeatable field and laboratory measurements of these quantities. Here, accurate elevation is measured using a ground-based differential global positioning system (GPS); other data acquisition methods could be applied to the same basic method. Soil samples are collected from prescribed depth intervals and analyzed in the lab using an efficient and precise modified pressure-calcimeter method for quantitative analysis of inorganic carbon concentration. Standard statistical methods are applied to point data, and representative results show significant correlations between changes in soil surface layer CaCO3 and changes in elevation consistent with the conceptual model; CaCO3 generally decreased in depositional areas and increased in erosional areas. Maps are derived from point measurements of elevation and soil CaCO3 to aid analyses. A map of erosional and depositional patterns at the study site, a rain-fed winter wheat field cropped in alternating wheat-fallow strips, shows the interacting effects of water and wind erosion affected by management and topography. Alternative sampling methods and depth intervals are discussed and recommended for future work relating soil erosion and deposition to soil CaCO3.

Spatial patterns of soil erosion and deposition can be inferred from differences in ground elevation mapped at appropriate time increments. Such changes in elevation are related to changes in near-surface soil carbonates. Repeatable methods for field and laboratory measurements of these quantities and data analysis methods are described here.

측정 및 토양 침식과 토양 탄산 농도 농업 관리에 관련 된 증 착 패턴 매핑

Spatial patterns of soil erosion and deposition can be inferred from differences in ground elevation mapped at appropriate time increments. Such changes ...

Experimental Protocol for Detecting Mitochondrial Function in Hepatocytes Exposed to Organochlorine Pesticides

This paper presents detailed methods on detecting hepatic mitochondrial function for a better understanding the cause of metabolic disorders caused by environmental organochlorine pesticides (OCPs) in hepatocytes. HepG2 cells were exposed to &#946;-hexachlorocyclohexane (&#946;-HCH) for 24 h at an equivalent dose of internal exposure in general population. Ultrastructure in hepatocytes was examined by transmission electron microscopy (TEM) to show the damage of mitochondria. Mitochondrial function was further evaluated by mitochondrial fluorescence intensity, adenosine 5'-triphosphate (ATP) levels, oxygen consumption rate (OCR) and mitochondrial membrane potential (MMP) in HepG2 cells incubated with &#946;-HCH. The mitochondria fluorescence intensity after stained by mitochondrial green fluorescent probe was observed with a fluorescence microscopy. The luciferin-luciferase reaction was used to determine ATP levels. The MMP was detected by the cationic dye JC-1 and analyzed under flow cytometry. OCR was measured with an extracellular flux analyzer. In summary, these protocols were used in detecting mitochondrial function in hepatocytes with to investigate mitochondria damages.

Understanding the influence of environmental organochlorine pesticides (OCPs) on mitochondrial function in hepatocytes is important in exploring the mechanism of OCPs causing metabolic disorders. This paper presents detailed methods on detecting hepatic mitochondrial function.

유기체 살충제에 노출된 간세포에서 미토콘드리아 기능을 검출하기 위한 실험 프로토콜

This paper presents detailed methods on detecting hepatic mitochondrial function for a better understanding the cause of metabolic disorders caused by ...

Experimental Methods of Dust Charging and Mobilization on Surfaces with Exposure to Ultraviolet Radiation or Plasmas

Electrostatic dust transport has been hypothesized to explain a number of observations of unusual planetary phenomena. Here, it is demonstrated using three recently developed experiments in which dust particles are exposed to thermal plasma with beam electrons, beam electrons only, or ultraviolet (UV) radiation only. The UV light source has a narrow bandwidth in wavelength centered at 172 nm. The beam electrons with the energy of 120 eV are created with a negatively biased hot filament. When the vacuum chamber is filled with the argon gas, a thermal plasma is created in addition to the electron beam. Insulating dust particles of a few tens of microns in diameter are used in the experiments. Dust particles are recorded to be lofted to a height up to a few centimeters with a launch speed up to 1 m/s. These experiments demonstrate that photo and/or secondary electron emission from a dusty surface changes the charging mechanism of dust particles. According to the recently developed &#34;patched charge model&#34;, the emitted electrons can be re-absorbed inside microcavities between neighboring dust particles below the surface, causing the accumulation of enhanced negative charges on the surrounding dust particles. The repulsive forces between these negatively charged particles may be large enough to mobilize and lift them off the surface. These experiments present the advanced understanding of dust charging and transport on dusty surfaces, and laid a foundation for future investigations of its role in the surface evolution of airless planetary bodies.

Dust charging and mobilization is demonstrated in three experiments with exposure to thermal plasma with beam electrons, beam electrons only, or ultraviolet (UV) radiation only. These experiments present the advanced understanding of electrostatic dust transport and its role in shaping the surfaces of airless planetary bodies.

먼지가 충전 및 자외선 또는 플라즈마에 노출 표면에 동원의 실험 방법

Electrostatic dust transport has been hypothesized to explain a number of observations of unusual planetary phenomena. Here, it is demonstrated using ...

Optimized Procedure for Determining the Adsorption of Phosphonates onto Granular Ferric Hydroxide using a Miniaturized Phosphorus Determination Method

This paper introduces a procedure to investigate the adsorption of phosphonates onto iron-containing filter materials, particularly granular ferric hydroxide (GFH), with little effort and high reliability. The phosphonate, e.g., nitrilotrimethylphosphonic acid (NTMP), is brought into contact with the GFH in a rotator in a solution buffered by an organic acid (e.g., acetic acid) or Good buffer (e.g., 2-(N-morpholino)ethanesulfonic acid) [MES] and N-cyclohexyl-2-hydroxyl-3-aminopropanesulfonic acid [CAPSO]) in a concentration of 10 mM for a specific time in 50 mL centrifuge tubes. Subsequently, after membrane filtration (0.45 &#181;m pore size), the total phosphorus (total P) concentration is measured using a specifically developed determination method (ISOmini). This method is a modification and simplification of the ISO 6878 method: a 4 mL sample is mixed with H2SO4 and K2S2O8 in a screw cap vial, heated to 148-150 &#176;C for 1 h and then mixed with NaOH, ascorbic acid and acidified molybdate with antimony(III) (final volume of 10 mL) to produce a blue complex. The color intensity, which is linearly proportional to the phosphorus concentration, is measured spectrophotometrically (880 nm). It is demonstrated that the buffer concentration used has no significant effect on the adsorption of phosphonate between pH 4 and 12. The buffers, therefore, do not compete with the phosphonate for adsorption sites. Furthermore, the relatively high concentration of the buffer requires a higher dosage concentration of oxidizing agent (K2S2O8) for digestion than that specified in ISO 6878, which, together with the NaOH dosage, is matched to each buffer. Despite the simplification, the ISOmini method does not lose any of its accuracy compared to the standardized method.

This paper introduces a procedure to investigate the adsorption of phosphonates onto iron-containing filter materials, particularly granular ferric hydroxide, with little effort and high reliability. In a buffered solution, the phosphonate is brought into contact with the adsorbent using a rotator and then analyzed via a miniaturized phosphorus determination method.

소형 인 결정 방법을 사용 하 여 세분화 된 제 2 철 수산화에 Phosphonates의 흡착을 결정 하기 위한 최적화 된 절차

This paper introduces a procedure to investigate the adsorption of phosphonates onto iron-containing filter materials, particularly granular ferric ...

The Plant Infection Test: Spray and Wound-Mediated Inoculation with the Plant Pathogen Magnaporthe Grisea

Plants possess a powerful system to defend themselves against potential threats by pathogenic fungi. For agriculturally important plants, however, current measures to combat such pathogens have proved too conservative and, thus, not sufficiently effective, and they can potentially pose environmental risks. Therefore, it is extremely necessary to identify host-resistance factors to assist in controlling plant diseases naturally through the identification of resistant germplasm, the isolation and characterization of resistance genes, and the molecular breeding of resistant cultivars. In this regard, there is need to establish an accurate, rapid, and large-scale inoculation method to breed and develop plant resistance genes. The rice blast fungal pathogen Magnaporthe grisea causes severe disease symptoms and yield losses. Recently, M. grisea has emerged as a model organism for studying the mechanisms of plant-fungal pathogen interactions. Hence, we report the development of a plant virulence test method that is specific for M. grisea. This method provides for both spray inoculation with a conidial suspension and wounding inoculation with mycelium cubes or droplets of conidial suspension. The key step of the wounding inoculation method for detached rice leaves is to make wounds on plant leaves, which avoids any interference caused by host penetration resistance. This spray/wounding protocol contributes to the rapid, accurate, and large-scale screening of the pathotypes of M. grisea isolates. This integrated and systematic plant infection method will serve as an excellent starting point for gaining a broad perspective of issues in plant pathology.

The Plant Infection Test: Spray and Wound-Mediated Inoculation with the Plant Pathogen Magnaporthe Grisea

Here, we present a protocol to test plant virulence with the plant pathogen Magnaporthe grisea. This report will contribute to the large-scale screening of the pathotypes of fungi isolates and serve as an excellent starting point for understanding the resistant mechanisms of plants during molecular breeding.

식물 감염 테스트: 스프레이 식물 병원 체 Magnaporthe Grisea 와 상처-중재 접종

Plants possess a powerful system to defend themselves against potential threats by pathogenic fungi. For agriculturally important plants, however, current ...

Experimental Study of the Relationship Between Particle Size and Methane Sorption Capacity in Shale

The amount of adsorbed shale gas is a key parameter used in shale gas resource evaluation and target area selection, and it is also an important standard for evaluating the mining value of shale gas. Currently, studies on the correlation between particle size and methane adsorption are controversial. In this study, an isothermal adsorption apparatus, the gravimetric sorption analyzer, is used to test the adsorption capacity of different particle sizes in shale to determine the relationship between the particle size and the adsorption capacity of shale. Thegravimetric method requires fewer parameters and produces better results in terms of accuracy and consistency than methods like the volumetric method. Gravimetric measurements are performed in four steps: a blank measurement, preprocessing, a buoyancy measurement, and adsorption and desorption measurements. Gravimetric measurement is presently considered to be a more scientific and accurate method of measuring the amount of adsorption; however, it is time-consuming and requires a strict measuring technique. A Magnetic Suspension Balance (MSB) is the key to verify the accuracy and consistency of this method. Our results show that adsorption capacity and particle size are correlated, but not a linear correlation, and the adsorptions in particles sieved into 40 - 60 and 60 - 80 meshes tend to be larger. We propose that the maximum adsorption corresponding to the particle size is approximately 250 &#181;m (60 mesh) in the shale gas fracturing.

We use an isothermal adsorption apparatus, the gravimetric sorption analyzer, to test the adsorption capacity of different particle sizes of shale, in order to find out the relationship between particle size and the adsorption capacity of shale.

입자 크기와 셰 일에서 메탄 수 착 용량 사이의 관계의 실험적 연구

The amount of adsorbed shale gas is a key parameter used in shale gas resource evaluation and target area selection, and it is also an important standard ...

Preparation of Biomass-based Mesoporous Carbon with Higher Nitrogen-/Oxygen-chelating Adsorption for Cu(II) Through Microwave Pre-Pyrolysis

An environment-friendly technique for synthesizing biomass-based mesoporous activated carbon with high nitrogen-/oxygen-chelating adsorption for Cu(II) is proposed. Bagasse impregnated with phosphoric acid is utilized as the precursor. To pyrolyze the precursor, two separate heating modes are used: microwave pyrolysis and conventional electric-heating pyrolysis. The resulting bagasse-derived carbon samples are modified with nitrification and reduction modification. Nitrogen (N)/oxygen (O) functional groups are simultaneously introduced to the surface of activated carbon, enhancing its adsorption of Cu(II) by complexing and ion-exchange. Characterization and copper adsorption experiments are performed to investigate the physicochemical properties of four prepared carbon samples and determine which heating method favors the subsequent modification for doping of N/O functional groups. In this technique, based on analyzing data of nitrogen adsorption, Fourier transform infrared spectroscopy, and batch adsorption experiments, it is proven that microwave-pyrolyzed carbon has more defect sites and, therefore, time-saving effective microwave pyrolysis contributes more N/O species to the carbon, although it leads to a lower specific surface area. This technique offers a promising route to synthesis adsorbents with higher nitrogen and oxygen content and a higher adsorption capacity of heavy-metal ions in wastewater remediation applications.

Preparation of Biomass-based Mesoporous Carbon with Higher Nitrogen-/Oxygen-chelating Adsorption for CuII Through Microwave Pre-Pyrolysis

Here, we present a protocol to synthesize nitrogen/oxygen dual-doped mesoporous carbon from biomass by chemical activation in different pyrolysis modes followed by modification. We demonstrate that the microwave pyrolysis benefits the subsequent modification process to simultaneously introduce more nitrogen and oxygen functional groups on the carbon.

바이오 매스 기반 Mesoporous 탄소 높은 질소-의 준비 / 전자 사전 열 분해를 통해 Cu(II)에 대 한 흡착 산소 킬레이트 화

An environment-friendly technique for synthesizing biomass-based mesoporous activated carbon with high nitrogen-/oxygen-chelating adsorption for Cu(II) is ...