The present research work was financially sponsored by the Ministry of Science and Technology of Taiwan under the grant NSC 94-2611-E-022-001, NSC 95-2221-E-022-018, NSC 96-2221-E-022-015MY3 and NSC 97-2221-E-022-013-MY3.

NOTE: The details of rotating test facilities, data acquisition, data processing and the heat transfer test module emulating an internal cooling channel of a gas turbine rotor blade are in our previous works29,30,31,32.
1. Preparation of Heat Transfer Tests
<ol>
	<li>Formulate the experimental conditions in terms of Re, Ro and Bu from the targeted operation conditions of a gas turbine rotor blade.</li>
	<li>Determine the N, P, d, R, and Tw - Tb needed for acquiring the tested Re, Ro and Bu using equations (14) and (15).</li>
	<li>Re-define the targeting Re, Ro and Bu if N, P, d, R, and Tw - Tb exceeds the limit of the experimental facilities.</li>
	<li>Design and construct the scaled heat transfer test module emulating a practical internal coolant channel in a gas turbine rotor blade2.</li>
</ol>
2. Determination of Thermal Emissivity Coefficient for Infrared Thermography System
<ol>
	<li>Install the calibrated thermocouple on the back side of the scanned stainless-steel heating foil.</li>
	<li>Spray a thin layer of black paint on the stainless-steel heating foil scanned by the infrared camera.</li>
	<li>Create symmetrical flow fields on two sides of the stainless-steel heating foil by placing a vertical thin stainless-steel foil in a space with the free convective flows over the two sides of the vertical heating foil.</li>
	<li>Feed electrical heating power through the heating foil and measure temperatures simultaneously by thermocouple and infrared thermography system from the computer display at steady state.</li>
	<li>Repeat step 2.4 at least four times using elevated heater powers. Ensure that the wall temperatures corresponding to the heater powers used by steps 2.3 and 2.4 cover the Tw range determined by step 1.2.</li>
	<li>Calculate the Tw values scanned by the infrared thermography system using a number of selective thermal emissivity coefficients for the program that converts the infrared signals into temperature data.</li>
	<li>Compare the Tw data measured by the calibrated thermocouple and the infrared thermography system at the location corresponding to the thermocouple spot with the standard deviations evaluated.</li>
	<li>Select the thermal emissivity coefficient with the minimum standard deviation determined by step 2.7.</li>
	<li>Determine the maximum precision error for the infrared thermography system using the thermal emissivity coefficient determined by step 2.8.</li>
</ol>
3. Dynamic Balance of Rotating Rig
<ol>
	<li>Install the heat transfer test module, the infrared camera, the enveloping frame and all accessories on the rotating rig.</li>
	<li>Adjust the counterbalancing weight gradually until the running condition of the rotating rig satisfies the vibrational limitation for the infrared thermographic measurements to exhibit the stable thermal image on the computer display.</li>
</ol>
4. Evaluation of Heat Loss Coefficients
<ol>
	<li>Fill the coolant channel of the heat transfer test module with thermal insulation material.</li>
	<li>Install the filled test module on the rotating test rig by fitting the test module on the rotating platform and connecting the heater power supply and all the instrumental cables.</li>
	<li>Activate the data acquisition system to scan the temporal Tw variation at a heating power until the steady state condition is satisfied. Ensure that the temporal Tw variations during several successive scans are less than +0.3 K at each steady state condition.</li>
	<li>Record the heater power, steady-state Tw data and the corresponding ambient temperature, T&#8734;.</li>
	<li>Repeat steps 4.3 and 4.4 at least five times using different heating powers at a fixed rotating speed.</li>
	<li>Repeat steps 4.2 - 4.4 with at least five rotating speeds. Ensure that the test range of the rotating speed covers all the N values determined by step 1.2.</li>
	<li>Repeat steps 4.3 - 4.6 with a reversed rotating direction.</li>
	<li>Construct the plots of heat loss flux against wall-to-ambient temperature difference at each rotating speed.</li>
	<li>Correlate the heat loss coefficients as the functions of wall-to-ambient temperature difference, rotating speed and direction of rotation.</li>
	<li>Incorporate the heat loss correlation into the post data process program for Nu accountancy.</li>
</ol>
5. Baseline Heat Transfer Tests
<ol>
	<li>Perform heat transfer tests at the targeting Reynolds numbers at zero rotating speed (Ro = N = 0) by feeding coolant flows and heater powers to the test module. Ensure the supplied coolant mass flow rate is constantly adjusted in order to control Reynolds number at the flow entry plane at the targeting value.</li>
	<li>Record all the relevant raw data, including the steady state wall temperatures, fluid temperatures, heater powers, flow pressures and ambient pressures and temperatures, for subsequent data processing.</li>
	<li>Evaluate the local and area-averaged Nusselt numbers (Nu0) over the scanned static channel walls.</li>
</ol>
6. Rotating Heat Transfer Tests
<ol>
	<li>Install the on-line monitoring program to monitor the test conditions at the targeting Re and Ro.</li>
	<li>Feed the measured coolant mass flow rate, airflow pressure, rotating speed and fluid temperature at channel entrance into the monitoring program to calculate the instant Re and Ro.</li>
	<li>Record all the relevant raw data, such as rotating speed, heater power, airflow and ambient pressures, as well as the wall and fluid temperatures for subsequent data processing after the pre-defined steady-state condition is satisfied.</li>
	<li>Repeat steps 6.2 and 6.3 with at least four ascending or descending heater powers at a set of fixed Re and Ro. Ensure that the test Re and Ro fall within &#177;1% differences from the targeting values by adjusting the rotating speed or the coolant mass flow rate or both.</li>
	<li>Ensure that the heat transfer tests at each set of fixed Re and Ro with different heater powers are continuously performed as the development of buoyancy induced flows is associated with the &#34;history&#34; of the flow development.</li>
	<li>Repeat steps 6.4 and 6.5 with four or five targeting Reynolds numbers (Re) at a fixed rotation number (Ro). Ensure the rotating speed is appropriately adjusted at each test Re to control both Re and Ro at the targeting values within &#177;1% differences.</li>
	<li>Repeat step 6.6 using four or five targeting rotation numbers (Ro).</li>
	<li>Repeat steps 6.2 to 6.7 with reversed rotating direction.</li>
	<li>Evaluate the local and area-averaged Nusselt numbers (Nu) over the scanned rotating channel walls using a post data processing program.</li>
</ol>
7. Parametric Analysis
<ol>
	<li>Correlate the area-averaged Nusselt numbers (Nu0) collected from the static channel into the functions of Reynolds number.</li>
	<li>Evaluate the full-field local Nu/Nu0 ratios at each fixed Re and Ro tested with the area-averaged Nu/Nu0 ratios calculated.</li>
	<li>Verify the applicability of isolation Re effect by plotting the local and area-averaged Nu/Nu0 ratios obtained with different Re but at identical Ro.</li>
	<li>Disclose the isolated impacts of rotating buoyancy on heat transfer properties of the rotating test channel by plotting the area-averaged Nu/Nu0 ratios collected at the same Ro with different Re against Bu or density ratio (&#916;&#961;/&#961;). Ensure the preferable selection of Bu or &#916;&#961;/&#961; to construct this type of plot for obtaining the consistent data trend with a simple functional structure for heat transfer correlation.</li>
	<li>Extrapolate each Nu/Nu0 data trend collected at a fixed Ro but different Re into the limiting condition of Bu&#8594;0 or &#916;&#961;/&#961;&#8594;0.</li>
	<li>Collect all the extrapolated Nu/Nu0 results with Bu&#8594;0 or &#916;&#961;/&#961;&#8594;0 at all the tested Ro.</li>
	<li>Plot the extrapolated Nu/Nu0 results with vanished buoyancy interaction against Ro to disclose the uncoupled Coriolis force effects on the heat transfer properties.</li>
	<li>Correlate the test results collected by steps 7.4 and 7.7 into the functions of Ro and Bu.</li>
</ol>

<ol>
	<li>Morris, W. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Heat transfer and fluid flow in rotating coolant channels. , ISBN 0471101214 (1981).</li><li>Morris, W. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+rotating+facility+to+study+heat+transfer+in+the+cooling+passage+of+turbine+rotor+blades.">A rotating facility to study heat transfer in the cooling passage of turbine rotor blades.</a> Journal of Power and Energy. 210 (1), 55-63 (1996).</li><li>Wagner, J. H., Johnson, B. V., Graziani, R. A., Yeh, F. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+rotating+passages+with+smooth+walls+and+radially+outward+flow.">Heat transfer in rotating passages with smooth walls and radially outward flow.</a> ASME Journal of Turbomachinery. 113 (1), 42-51 (1991).</li><li>Wagner, J. H., Johnson, B. V., Kopper, F. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+rotating+serpentine+passages+with+smooth+walls.">Heat transfer in rotating serpentine passages with smooth walls.</a> ASME Journal of Turbomachinery. 113 (3), 321-330 (1991).</li><li>Wagner, J. H., Johnson, B. V., Steuber, G. D., Yeh, F. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+rotating+serpentine+passages+with+trips+normal+to+the+flow.">Heat transfer in rotating serpentine passages with trips normal to the flow.</a> ASME Journal of Turbomachinery. 114 (4), 847-857 (1992).</li><li>Johnson, B. V., Wagner, J. H., Steuber, G. D., Yeh, F. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+rotating+serpentine+passages+with+selected+model+orientations+for+smooth+or+skewed+trip+walls.">Heat transfer in rotating serpentine passages with selected model orientations for smooth or skewed trip walls.</a> ASME Journal of Turbomachinery. 116 (4), 738-744 (1992).</li><li>Hwang, G. J., Tzeng, S. C., Mao, C. P., Soong, C. Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+a+radially+rotating+four-pass+serpentine+channel+with+staggered+half-v+rib+turbulators.">Heat transfer in a radially rotating four-pass serpentine channel with staggered half-v rib turbulators.</a> ASME Journal of Heat Transfer. 123 (1), 39-50 (2001).</li><li>Azad, G. S., Uddin, M. J., Han, J. C., Moon, H. K., Glezer, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+a+two-pass+rectangular+rotating+channel+with+45-deg+angled+rib+turbulators.">Heat transfer in a two-pass rectangular rotating channel with 45-deg angled rib turbulators.</a> ASME Journal of Turbomachinery. 124 (2), 251-259 (2002).</li><li>Griffith, T. S., Al-Hadhrami, L., Han, J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+rotating+rectangular+cooling+channels+(AR=4)+with+angled+ribs.">Heat transfer in rotating rectangular cooling channels (AR=4) with angled ribs.</a> ASME Journal of Heat Transfer. 124 (4), 617-625 (2002).</li><li>Al-Hadhrami, L., Griffith, T. S., Han, J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+two-pass+rotating+rectangular+channels+(AR=2)+with+five+different+orientations+of+45+deg+V-shaped+rib+turbulators.">Heat transfer in two-pass rotating rectangular channels (AR=2) with five different orientations of 45 deg V-shaped rib turbulators.</a> ASME Journal of Heat Transfer. 125 (2), 232-242 (2003).</li><li>Chang, S. W., Liou, T. M., Hung, J. H., Yeh, W. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+a+radially+rotating+square-sectioned+duct+with+two+opposite+walls+roughened+by+45+deg+staggered+ribs+at+high+rotation+numbers.">Heat transfer in a radially rotating square-sectioned duct with two opposite walls roughened by 45 deg staggered ribs at high rotation numbers.</a> ASME Journal of Heat Transfer. 129 (2), 188-199 (2007).</li><li>Zhou, F., Lagrone, J., Acharya, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Internal+cooling+in+4:1+AR+passages+at+high+rotation+numbers.">Internal cooling in 4:1 AR passages at high rotation numbers.</a> ASME Journal of Heat Transfer. 129 (12), 1666-1675 (2007).</li><li>Liu, Y. H., Huh, M., Han, J. C., Chopra, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+a+two-pass+rectangular+channel+(AR=1:4)+under+high+rotation+numbers.">Heat transfer in a two-pass rectangular channel (AR=1:4) under high rotation numbers.</a> ASME Journal of Heat Transfer. 130 (8), (2008).</li><li>Chang, S. W., Liou, T. M., Chiou, S. F., Chang, S. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+high-speed+rotating+trapezoidal+duct+with+rib-roughened+surfaces+and+air+bleeds+from+the+wall+on+the+apical+side.">Heat transfer in high-speed rotating trapezoidal duct with rib-roughened surfaces and air bleeds from the wall on the apical side.</a> ASME Journal of Heat Transfer. 130 (6), (2008).</li><li>Wright, L. M., Liu, Y. H., Han, J. C., Chopra, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+trailing+edge,+wedge-shaped+cooling+channels+under+high+rotation+numbers.">Heat transfer in trailing edge, wedge-shaped cooling channels under high rotation numbers.</a> ASME Journal of Heat Transfer. 130 (7), 1-11 (2008).</li><li>Liou, T. M., Chen, M. Y., Tsai, M. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fluid+flow+and+heat+transfer+in+a+rotating+two-pass+square+duct+with+in-line+90-deg+ribs.">Fluid flow and heat transfer in a rotating two-pass square duct with in-line 90-deg ribs.</a> ASME Journal of Turbomachinery. 124 (2), 260-268 (2002).</li><li>Chang, S. W., Liou, T. M., Yang, T. L., Hong, G. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+radially+rotating+pin-fin+channel+at+high+rotation+numbers.">Heat transfer in radially rotating pin-fin channel at high rotation numbers.</a> ASME Journal of Turbomachinery. 132 (2), (2010).</li><li>Rallabandi, A., Lei, J., Han, J. C., Azad, S., Lee, C. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+measurements+in+rotating+blade-shape+serpentine+coolant+passage+with+ribbed+walls+at+high+Reynolds+numbers.">Heat transfer measurements in rotating blade-shape serpentine coolant passage with ribbed walls at high Reynolds numbers.</a> ASME Journal of Turbomachinery. 136 (9), (2014).</li><li>Mayo, I., Arts, T., Ahmed, E. H., Parres, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two-dimensional+heat+transfer+distribution+of+a+rotating+ribbed+channel+at+different+Reynolds+numbers.">Two-dimensional heat transfer distribution of a rotating ribbed channel at different Reynolds numbers.</a> ASME Journal of Turbomachinery. 137 (3), (2015).</li><li>Chang, S. W., Yang, T. L., Liou, T. M., Fang, H. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+rotating+scale-roughened+trapezoidal+duct+at+high+rotation+numbers.">Heat transfer in rotating scale-roughened trapezoidal duct at high rotation numbers.</a> Applied Thermal Engineering. 29 (8), 1682-1693 (2009).</li><li>Liou, T. M., Chang, S. W., Chen, J. S., Yang, T. L., Lan, Y. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Influence+of+channel+aspect+ratio+on+heat+transfer+in+rotating+rectangular+ducts+with+skewed+ribs+at+high+rotation+numbers.">Influence of channel aspect ratio on heat transfer in rotating rectangular ducts with skewed ribs at high rotation numbers.</a> International Journal of Heat Mass Transfer. 52 (23), 5309-5322 (2009).</li><li>Huh, M., Liu, Y. H., Han, J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+rib+height+on+heat+transfer+in+a+two+pass+rectangular+channel+(AR+=+1:4)+with+a+sharp+entrance+at+high+rotation+numbers.">Effect of rib height on heat transfer in a two pass rectangular channel (AR = 1:4) with a sharp entrance at high rotation numbers.</a> International Journal of Heat Mass Transfer. 52 (19), 4635-4649 (2009).</li><li>Xu, G., Li, Y., Deng, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+rib+spacing+on+heat+transfer+and+friction+in+a+rotating+two-pass+square+channel+with+asymmetrical+90-deg+rib+turbulators.">Effect of rib spacing on heat transfer and friction in a rotating two-pass square channel with asymmetrical 90-deg rib turbulators.</a> Applied Thermal Engineering. 80 (5), 386-395 (2015).</li><li>Tao, Z., Yang, M., Deng, H., Li, H., Tian, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+study+in+a+rotating+ribbed+two-pass+channel+with+engine-similar+cross+section+at+high+rotation+number.">Heat transfer study in a rotating ribbed two-pass channel with engine-similar cross section at high rotation number.</a> Applied Thermal Engineering. 106 (5), 681-696 (2016).</li><li>Li, Y., Deng, H., Tao, Z., Xu, G., Chen, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+characteristics+in+a+rotating+trailing+edge+internal+cooling+channel+with+two+coolant+inlets.">Heat transfer characteristics in a rotating trailing edge internal cooling channel with two coolant inlets.</a> International Journal of Heat Mass Transfer. 105 (2), 220-229 (2017).</li><li>Deng, H., Chen, Y., Tao, Z., Li, Y., Qiu, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+a+two-inlet+rotating+rectangular+channel+with+side-wall+fluid+extraction.">Heat transfer in a two-inlet rotating rectangular channel with side-wall fluid extraction.</a> International Journal of Heat and Mass Transfer. 105 (2), 525-534 (2017).</li><li>You, R., Li, H., Tao, Z., Wei, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+investigation+in+a+smooth+rotating+channel+with+thermography+liquid+crystal.">Heat transfer investigation in a smooth rotating channel with thermography liquid crystal.</a> ASME Turbo Expo. GT2016-56413, Turbomachinery Technical Conference and Exposition: Heat Transfer. 5 (B), V05BT16A006 1~10 (2016).</li><li>Morris, W. D., Chang, S. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+experimental+study+of+heat+transfer+in+a+simulated+turbine+blade+cooling+passage.">An experimental study of heat transfer in a simulated turbine blade cooling passage.</a> International Journal of Heat Mass Transfer. 40 (15), 3703-3716 (1997).</li><li>Chang, S. W., Liou, T. -. M., Po, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Coriolis+and+rotating+buoyancy+effect+on+detailed+heat+transfer+distributions+in+a+two-pass+square+channel+roughened+by+45&#176;+ribs+at+high+rotation+numbers.">Coriolis and rotating buoyancy effect on detailed heat transfer distributions in a two-pass square channel roughened by 45&#176; ribs at high rotation numbers.</a> International Journal of Heat Mass Transfer. 53 (7), 1349-1363 (2010).</li><li>Wang, W. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Heat transfer in rotating twin-pass trapezoidal-sectioned passage with two opposite walls roughened by 45 degree ribs. , (2006).</li><li>Chang, S. W., Wu, P. -. S., Chen, C. -. S., Weng, C. -. C., Jiang, Y. -. R., Shih, S. -. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Thermal+performance+of+radially+rotating+two-pass+S-shaped+zig-zag+channel.">Thermal performance of radially rotating two-pass S-shaped zig-zag channel.</a> International Journal of Heat and Mass Transfer. 115 (B), 1011-1031 (2017).</li><li>Chang, S. W., Lees, A. W., Liou, T. -. M., Hong, G. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+of+a+radially+rotating+furrowed+channel+with+two+opposite+skewed+sinusoidal+wavy+walls.">Heat transfer of a radially rotating furrowed channel with two opposite skewed sinusoidal wavy walls.</a> International Journal of Thermal Sciences. 49 (5), 769-785 (2010).</li><li>Chang, S. W., Liou, T. -. M., Lee, T. -. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+of+a+rotating+rectangular+channel+with+a+diamond-shaped+pin-fin+array+at+high+rotation+numbers.">Heat transfer of a rotating rectangular channel with a diamond-shaped pin-fin array at high rotation numbers.</a> Journal of Turbomachinery Transactions of the ASME. 135 (4), (2013).</li><li>Morris, W. D., Chang, S. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heat+transfer+in+a+radially+rotating+smooth-walled+tube.">Heat transfer in a radially rotating smooth-walled tube.</a> The Aeronautical Journal. 102 (1015), 277-285 (1998).</li></ol>

The authors have nothing to disclose.

While the endwall temperatures of a rotating channel are detected by an infrared thermography system, the fluid temperatures are measured by thermocouples. As the alternative magnetic field of an AC motor that drives a rotating rig induces electrical potential to interfere the thermocouple measurements, the DC motor must be adopted to drive a rotating test rig.
The fluid temperature distribution over the exit plane of a heated channel is not uniform. At least five thermocouples on the existing plane of a rotating channel are recommended for measuring the local fluid exit temperatures. In particular, these thermocouples measuring the fluid temperatures installed in the flow passage are subject to centrifugal forces during the rotating tests. The thermocouple wires are easily bent toward the hot channel walls. Thus, a shielded thermocouple cable for measuring the fluid entry temperature is used. On the flow exit plane, a mesh with several thermocouple beads weaved on the mesh can be sandwiched between the exit flanges of a test channel to detect the fluid exit temperatures at the predefined locations under a rotating test condition.
With considerable rotation induced buoyancy effects on the flow and heat transfer characteristics of a rotating channel, the method selected to detect the full-field heat transfer data needs to include both Coriolis-force and buoyancy effects. Using the transient liquid crystal method for measuring the full-field heat transfer data, the thermal boundary layers are not yet fully developed as the temporal channel-wall temperature variations are essential by this method for acquiring the convective heat transfer coefficients. As the centripetal acceleration could reach 105 x g in a coolant channel of a rotating gas turbine blade, the heat transfer data subject to the influences of the fully developed buoyancy flows, which are detectable by the present experimental method, are more practical for design activities.
The exposure of the scanned hot channel wall to an infrared camera inevitably incurs heat loss from the Joule heat generated by the heating foils. The protocols for conducting the heat loss calibration tests are critical for ensuring the quality of heat transfer data. Inheriting either from the free or forced convective external flows for a static or rotating test channel, the convective heat transfer coefficients can be correlated as the function of wall-to-ambient temperature difference at a fixed rotating speed (Figure 2). It is preferable to envelop the entire rotating heat transfer test module with a shield for recovering the &#34;free-convective&#34; like external flows during the rotating tests. The maximum experimental uncertainties of heat transfer data are generally reduced when the percentage of the heat loss flux from the supplied heat flux is reduced. Nevertheless, the heat loss coefficients are slightly increased as N increases even with the enveloped shield covering the entire heat transfer test module (Figure 3). The heat loss correlation is included in the post data processing program to evaluate the distribution of local heat loss flux for each set of heat transfer test results. As the thermal inertia of the heat transfer module filled by thermal insulation material is considerably increased, the time required for reaching the steady-state condition during each heat loss test is considerably extended from a heat transfer test with airflow.
It is essential to investigate the applicability of the isolating Re effect on heat transfer properties from those induced by rotation. As the Re effect on heat transfer performances depends on the channel configurations, it is not appropriate to customarily adopt the heat transfer correlations generated from other channel geometries as the static-channel heat transfer references. The present experimental method isolates Re impact from Ro and Bu effects by presenting the heat transfer data in terms of Nu/Nu0, in which the Nu0 data are measured for the static test channel. While the buoyancy effect in a rotation channel with centripetal acceleration about 105 x g is considerable, the gravitation-driven buoyancy effect on the heat transfer property of a static channel is generally negligible within the typical range of fluid density ratios examined for a static test channel.
During a heat transfer test after feeding heater power to generate the required temperature gradients for facilitating heat convection, a certain degree of buoyancy effect driven by the induced centripetal acceleration field in the rotating channel is inevitable. Such coupled Ro and Bu effects for a rotating channel at the realistic engine conditions are not negligible due to the extremely high centripetal accelerations. Thus, both Coriolis force and rotating buoyancy level are simultaneously altered when the rotating speed is adjusted. The simultaneous control of Ro and Re at the targeting values during the rotating experiment is essential for decoupling the Ro and Bu effects on heat transfer properties. Having fixed both Ro and Re, the heat transfer variations corresponding to the variation of heat flux, or buoyancy level, reflect the rotating buoyancy effect on heat transfer properties at the tested Ro. The Nu/Nu0 data converted from the data set generated in this manner permit the implementation of steps 7.4 - 7.8 for identifying the Coriolis force effect and rotating buoyance effect in isolation.
The Bu impact on the heat transfer property of a rotating channel is often Ro dependent as exemplified by Figure 6 in which the &#968;2 values are varied as Ro changes. It is not appropriate to select the mathematic structure of the heat transfer correlation that treats the Ro and Bu as the independent parameters in the correlation.
In view of the Nu/Nu0 extrapolation toward the limiting condition of Bu&#8594;0, the linear-like Nu/Nu0 variations against the selected buoyancy parameter is preferable in order to reduce the uncertainty caused by the data extrapolation. In this regard, the fluid density ratio, &#916;&#961;/&#961; or the buoyancy number, Bu, is recommended as the buoyancy parameter for disclosing the zero-buoyancy Nu/Nu0 level during such data extrapolating process.
With high pressure rotating tests, the deformations of heating foils and the constituent components of a rotating channel due to the thermal expansions at various patterns of temperature distribution often cause airflow leakage during the rotating test. Such small airflow leakage is difficult to be identified during the rotating test. Thus, immediate subsequent data processing is recommended for acquiring the heat transfer data of the rotating channel. By cross-examining the heat transfer results obtained from the previous rotating tests, the implication of any inconsistent data trend is the possible airflow leakage. The subsequent measures to detect and then prevent the airflow leakage are required.
We have demonstrated a method for generating the heat transfer data of a rotating channel at the realistic engine conditions with the Coriolis-force effect and rotating buoyancy effect uncoupled. The major limitation of the present experimental method for extending the test ranges of Ro and Bu is the sustainability of the infrared camera that rotates with the test channel. In general, 10 x g is the maximum sustainable centrifugal acceleration for an infrared camera. With respect to the existing method detecting the heat transfer rates of a rotating channel, the use of thin heating foil can minimize the effects of channel-wall conduction on the distribution of local convective heat flux and the detection of temperatures at wall-fluid interfaces. Also, the two-dimensional full-field heat transfer distribution over a rotating surface subject to the steady-state buoyancy effect are detectable using the present experimental technique. With the data analysis method developed, the influences of Coriolis force and rotating buoyancy on the full-field heat transfer property of a rotating channel can be uncoupled. This method has already been applied to a wide range of rotating channel configurations. We expect that the present experimental strategy can lead to the design- friendly heat transfer correlations and which will continue to extend for the full coverage of realistic engine conditions when the advancement of infrared camera technology permits its usages at the conditions with higher centrifugal accelerations.

While thermodynamic laws dictate the improved specific power and thermal efficiency of a gas turbine engine by elevating the turbine entry temperature, several hot engine components, such as turbine blades, are prone to thermal damage. Internal cooling of a gas turbine rotor blade permits a turbine entry temperature in excess of the temperature limits of the creep resistance of the blade material. However, the configurations of the internal cooling channels must comply with the blade profile. In particular, the coolant rotates within the rotor blade. With such harsh thermal conditions for a running gas turbine rotor blade, an effective blade cooling scheme is crucial to ensure the structure&#39;s integrity. Thus, the local heat transfer properties for a rotating channel are important for the efficient usage of the limited coolant flow available. The acquisition of useful heat transfer data that are applicable to the design of the internal coolant passages at realistic engine conditions is of primary importance when an experimental method is developed for measuring the heat transfer properties of a simulated cooling passage inside a gas turbine rotor blade.
Rotation at a speed above 10,000 rpm considerably alters the cooling performance of a rotating channel inside a gas turbine rotor blade. The identification of engine conditions for such a rotating channel is permissible using the similarity law. With rotation, the dimensionless groups that control the transport phenomena inside a radially rotating channel can be revealed by deriving the flow equations relative to a rotating frame of reference. Morris1 has derived the momentum conservation equation of flow relative to a rotating frame of reference as:
<img alt="Equation 1" src="/files/ftp_upload/57630/57630eq1.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(1)
In equation (1), the local fluid velocity, v&#772;, with the position vector, r&#772;, relative to a frame of reference rotating at the angular velocity, &#969;, is affected by the Coriolis acceleration in terms of 2(&#969;&#215;v&#772;), the decoupled centripetal buoyancy force, &#946;(T-Tref)(&#969;&#215;&#969;&#215;r&#772;), the driven piezo-metric pressure gradient, <img alt="Equation 16" src="/files/ftp_upload/57630/57630eq16.jpg" />, and the fluid dynamic viscosity, &#957;. The referenced fluid density, &#961;ref, is referred to a pre-defined fluid reference temperature Tref, which is typical of the local fluid bulk temperature for experiments. If the irreversible conversion of mechanical energy into thermal energy is negligible, the energy conservation equation is reduced to:
<img alt="Equation 2" src="/files/ftp_upload/57630/57630eq2.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(2)
The first term of equation (2) is obtained by treating the specific enthalpy to be directly related to the local fluid temperature, T, via the constant specific heat, Cp. As the perturbation of fluid density caused by the variation of fluid temperature in a heated rotating channel provides considerable influence on the motion of fluids when it links with the centripetal acceleration in equation (1), the fluid velocity and temperature fields in an axially rotating channel are coupled. Also, both Coriolis and centripetal accelerations vary simultaneously as the rotating speed is adjusted. Thus, the effects of Coriolis force and rotating buoyancy on the fields of fluid velocity and temperature are naturally coupled.
Equations (1) and (2) in the dimensionless forms disclose the flow parameters that govern the heat convection in a rotating channel. With a basically uniform heat flux imposed on a rotating channel, the local fluid bulk temperature, Tb, increases linearly in the streamwise direction, s, from the reference inlet level, Tref. The local fluid bulk temperature is determined as Tref + &#964;s, where &#964; is the gradient of the fluid bulk temperature in the direction of flow. Substitutions of the following dimensionless parameters of:
<img alt="Equation 3" src="/files/ftp_upload/57630/57630eq3.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(3)
<img alt="Equation 4" src="/files/ftp_upload/57630/57630eq4.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(4)
<img alt="Equation 5" src="/files/ftp_upload/57630/57630eq5.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(5)
<img alt="Equation 6" src="/files/ftp_upload/57630/57630eq6.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(6)
<img alt="Equation 7" src="/files/ftp_upload/57630/57630eq7.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(7)
into equations (1) and (2), where Vmean, N and d respectively stand for the mean flow through velocity, rotating velocity and channel hydraulic diameter, the dimensionless flow momentum and energy equations are derived as equations (8) and (9) respectively.
<img alt="Equation 8" src="/files/ftp_upload/57630/57630eq8.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(8)
<img alt="Equation 9" src="/files/ftp_upload/57630/57630eq9.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(9)
Evidently, &#951; in equation (9) is a function of Re, Ro, and Bu = Ro2&#946;&#964;dR, which are respectively referred to as Reynolds, rotation and buoyancy numbers. The Rossby number that quantifies the ratio between inertial and Coriolis forces is equivalent to the inverse rotation number in equation (8).
When Tb is calculated as Tref + &#964;s in a rotating channel subject to a uniform heat flux, the &#964; value can be alternatively evaluated as Qf/(mCpL) in which Qf, m and L are the convective heating power, coolant mass flow rate and channel length, respectively. Thus, the dimensionless local fluid bulk temperature, &#951;b, is equal to s/d and the dimensionless temperature at channel wall, &#951;w, yields [(Tw-Tb)/Qf][mCp][L/d]+s/d. With the convective heat transfer rate defined as Qf/(Tw-Tb), the dimensionless wall-to-fluid temperature difference, &#951;w-&#951;b, is convertible into the local Nusselt number via equation (10) in which &#950; is the dimensionless shape function of heating area and channel sectional area.
<img alt="Equation 10" src="/files/ftp_upload/57630/57630eq10.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(10)
With a set of predefined geometries and the hydrodynamic and thermal boundary conditions, the dimensionless groups controlling the local Nusselt number of a rotating channel are identified as:
<img alt="Equation 11" src="/files/ftp_upload/57630/57630eq11.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(11)
<img alt="Equation 12" src="/files/ftp_upload/57630/57630eq12.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(12)
<img alt="Equation 13" src="/files/ftp_upload/57630/57630eq13.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(13)
With experimental tests, the adjustment of rotating speed, N, for varying Ro to generate the heat transfer data at different strengths of Coriolis forces inevitably changes the centripetal acceleration, and thus, the relative strength of rotating buoyancy. Moreover, a set of heat transfer data collected from a rotating channel is always subject to a finite degree of rotating buoyancy effect. To disclose the individual effects of Coriolis-force and buoyancy on the heat transfer performance of a rotating channel requires the uncoupling of the Ro and Bu effects on Nu properties through the post data processing procedure that is inclusive in the present experimental method.
The engine and laboratory flow conditions for a rotating channel inside a gas turbine rotor blade can be specified by the ranges of Re, Ro and Bu. The typical engine conditions for the coolant flow through a gas turbine rotor blade, as well as the construction and commissioning of the rotating test facility that allowed experiments to be performed near the actual engine conditions was reported by Morris2. Based on the realistic engine conditions summarized by Morris2, Figure 1 constructs the realistic operating conditions in terms of Re, Ro and Bu ranges for a rotating coolant channel in a gas turbine rotor blade. In Figure 1, the indication of an engine&#39;s worst condition is referred to as the engine running condition at the highest rotor speed and the highest density ratio. In Figure 1, the lower limit and worst engine operating conditions respectively emerge at the lowest and highest engine speeds. It is extremely difficult to measure the full-field Nu distribution of a rotating channel running at a real engine speed between 5000 and 20,000 rpm. However, based on the similarity law, laboratory-scale tests have been conducted at reduced rotating speeds but with several attempts to provide a full coverage of the real-engine Re, Ro and Bu ranges. As an innovative experimental method, the NASA HOST program3,4,5,6 adopted the high-pressure tests for increasing the fluid densities at the predefined Re in order to extend the Ro range by reducing the mean fluid velocity. In this regard, the specific relationships between Re, Ro and Bu for an ideal gas with a gas constant, Rc, and viscosity, &#956;, are related as:
<img alt="Equation 14" src="/files/ftp_upload/57630/57630eq14.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(14)
<img alt="Equation 15" src="/files/ftp_upload/57630/57630eq15.jpg" />&#160;&#160;&#160;&#160;&#160;&#160;(15)
To bring the laboratory conditions into the nominal correspondence with engine conditions seen in Figure 1, the rotating speed, N, coolant pressure, P, channel hydraulic diameter, d, rotating radius, R, and wall-to-fluid temperature difference, Tw-Tb, need to be controlled for matching the realistic Re, Ro and Bu ranges. Clearly, one of the most effective approaches to extend the Ro range is to increase channel hydraulic diameter, as Ro is proportional to d2. As the laboratory heat transfer test at realistic N is extremely difficult, the coolant pressure, P, is technically easier to be raised for extending Ro range; even if Ro is only proportional to P. Based on this theoretical background, the design philosophy of the present experimental method is to increase Ro by pressurizing the rotating test channel using the maximum channel hydraulic diameter allowed to fit into the rotating rig. Having increased the Ro range, the range of Bu is accordingly extended as Bu is proportional to Ro2. In Figure 1, the laboratory test conditions adopted to generate the heat transfer data of rotating channels are also included3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29. As indicated in Figure 1, the coverage of realistic engine conditions by the available heat transfer data is still limited, especially for the required Bu range. The open and the colored solid symbols depicted in Figure 1 are the pointed and full-field heat transfer experiments, respectively. As collected in Figure 1, most of the heat transfer data with cooling applications to gas turbine rotor blades1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,20,21,22,23,24,25,26 are point measurements using the thermocouple method. The wall conduction effects on measuring the wall conductive heat flux and the temperatures at fluid-wall interfaces undermine the quality of heat transfer data converted from the thermocouple measurements. Also, the heat transfer measurements1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,20,21,22,23,24,25,26 using the thermocouple method cannot detect the two-dimensional heat transfer variations over a rotating surface. With the present experimental method29,30,31,32, the detection of full-field Nusselt number distributions over the rotating channel wall is permissible. The minimization of wall conduction effect using 0.1 mm thick stainless-steel foils with Biot numbers &#62;&#62;1 to generate the heating power by the present experimental method permits the one-dimensional heat conduction from the heating foil to the coolant flow. In particular, the acquisition of full-field heat transfer data involving both Ro and Bu effects is not permissible using the transient liquid crystal technique and the thermocouple method. With the current steady-state liquid crystal thermography method19, the detectable temperature range of 35-55 &#176;C disables the generation of heat transfer data with realistic density ratios.
Using the flow parameters governing the heat convection in a rotating channel to demonstrate that the full coverage of realistic engine conditions seen in Figure 1 has not yet been achieved, so the need for acquiring the full-field heat transfer data at realistic engine conditions has been continuously urged. The present experimental method enables the generation of full-field heat transfer with both Coriolis-force and rotating-buoyancy effects detected. The protocols are aimed at assisting the investigators to devise an experimental strategy relevant to the realistic full-field heat transfer measurement of a rotating channel. Along with the method of parametric analysis that is unique to the present experimental method, the generation of heat transfer correlation for assessing the isolated and interdependent Ro and Bu effects on Nu is permitted.
The article illustrates an experimental method aimed at generating the two-dimensional heat transfer data of a rotating channel with flow conditions similar to the realistic gas turbine engine conditions but operating at much lower rotating speeds in the laboratories. The method developed to select the rotating speed, the hydraulic diameter of test channel and the range of wall-to-fluid temperature differences for acquiring the heat transfer data at realistic engine conditions is illustrated in the introduction. The calibration tests for the infrared thermography system, the heat loss calibration tests and the operation of the rotating heat transfer test rig are shown. The factors causing the significant uncertainties for heat transfer measurements and the procedures for decoupling the Coriolis-force and buoyancy effects on the heat transfer properties of a rotating channel are described in the article with the selective results to demonstrate the present experimental method.

<table>
	<tbody>
		<tr>
			<td>Rotating test rig</td>
			<td>In-house made</td>
			<td></td>
			<td>Design by this research group</td>
		</tr>
		<tr>
			<td>Heat transfer test module</td>
			<td>In-house made</td>
			<td></td>
			<td>Design by this research group</td>
		</tr>
		<tr>
			<td>Mass flow meter</td>
			<td>Eldride Product, Inc.</td>
			<td>3100301-01-01 
			359-1007</td>
			<td></td>
		</tr>
		<tr>
			<td>Infrared thermography system</td>
			<td>NEC P384A-8</td>
			<td>3100401-04 
			3127A-4</td>
			<td></td>
		</tr>
		<tr>
			<td>Instrumentation slip ring</td>
			<td>Michigan Scientific SR36M</td>
			<td>3100506-62 
			3553-372</td>
			<td></td>
		</tr>
	</tbody>
</table>

uncoupling coriolis force and rotating buoyancy effects on full-field heat transfer properties of a rotating channel

An experimental method for exploring the heat transfer characteristics of an axially rotating channel is proposed. The governing flow parameters that characterize the transport phenomena in a rotating channel are identified via the parametric analysis of the momentum and energy equations referring to a rotating frame of reference. Based on these dimensionless flow equations, an experimental strategy that links the design of the test module, the experimental program and the data analysis is formulated with the attempt to reveal the isolated Coriolis-force and buoyancy effects on heat transfer performances. The effects of Coriolis force and rotating buoyancy are illustrated using the selective results measured from rotating channels with various geometries. While the Coriolis-force and rotating-buoyancy impacts share several common features among the various rotating channels, the unique heat transfer signatures are found in association with the flow direction, the channel shape and the arrangement of heat transfer enhancement devices. Regardless of the flow configurations of the rotating channels, the presented experimental method enables the development of physically consistent heat transfer correlations that permit the evaluation of isolated and interdependent Coriolis-force and rotating-buoyancy effects on the heat transfer properties of rotating channels.

Realistic operating conditions for the internal coolant flows inside a rotating gas turbine blade in terms of Re, Ro and Bu are compared with the emulated laboratory conditions in Figure 1. The data points fall in the realistic engine conditions using the present experimental method summarized in the protocols11,14,17,20,21. Although the full-field heat transfer data are more useful than the pointed heat transfer data measured from the rotating channels, most of the previous heat transfer experiments adopt the thermocouple method (Figure 1). The present infrared thermography method detects the full-field heat transfer information from a rotating surface with the buoyancy-induced flows fully developed. With the free or forced convective external flows for a static or rotating test channel, the present protocols include the generation of heat loss correlations for post data processing (Figure 2). At the top of Figure 2, the construction of the heat transfer test module is also demonstrated. The correlative coefficients for all the fitted lines shown by Figure 2 fall between 0.95-0.98. In view of the hloss correlation seen in the plot of hloss against N in Figure 2, the error bars indicate the data range determined at each rotating speed.
Figure 3, Figure 4, and Figure 5 depict the selective heat transfer results measured from the static two-pass S-channel with longitudinal wavy ribs, the rotating two-pass S-channel31 and the rotating furrowed32 and pin-fin channel33. The estimated maximum uncertainties of the Nu measurements for the static S-ribbed channel, the rotating S-channel31, furrowed channel32 and pin-fin channel33 are 7.9%, 8.8%, 9.2%, and 9.7%, respectively. To disclose the Re impact on the heat transfer properties of a coolant channel, the base-line full-field heat transfer data detected from the static channel by the present infrared thermography method as typified by Figure 3 are essential. The diagram shown at the top of Figure 3 also depicts the channel configuration of the two-pass S-channel with the longitudinal wavy ribs. The channel section is square with the semi-circular sectioned longitudinal wavy ribs on two opposite heated walls of the inlet and outlet legs.
The applicability of isolated Re impact from Ro and Bu effects on local and regionally averaged heat transfer is permitted by presenting the heat transfer data in terms of Nu/Nu0 (Figure 4). Both patterns and levels of Nu/Nu0 at the same Ro with similar Bu seem to be weak functions of Re (Figure 4). The typical results from the protocol for disclosing the isolated Coriolis force effects on heat transfer properties are demonstrated in Figure 5. In Figure 5, the variations of Nu/Nu0 at each fixed Ro against Bu for two different rotating channels with wavy endwalls32 and diamond shaped pin-fins33 tend to follow linear-like data trends. Thus, the linear extrapolation when Bu&#8594;0 is selected for the identified Nu/Nu0 levels at Bu = 0 and Ro&#62;0. But, due to the different channel configurations, the Nu/Nu0 ratios measured from the rotating furrowed32 and pin-fin33 channels as depicted in Figure 5 are respectively decreased and increased by raising Bu. In this regard, the depiction of Nu/Nu0 variations against density ratio (&#916;&#961;/&#961;)3,4,5,6,34 has often led to the non-linear Nu/Nu0 variations. Thus, the extrapolation of each Nu/Nu0 data trend at a fixed Ro toward the asymptotic limit of &#916;&#961;/&#961;&#8594;0 with diminished buoyancy effect along a non-linear data trend is often affected by the type of correlative function selected. Nevertheless, the data extrapolating procedure for the heat transfer results detected from the leading and trailing walls of the rotating channels32 demonstrates the applicability to unravel the isolated Coriolis force effects on heat transfer properties with vanished buoyancy interaction at Bu=0 (Figure 5).
The so-called zero-buoyancy Nu/Nu0 ratios are only controlled by Ro to reflect the isolated Coriolis force effects. The manner of heat transfer variations from the static-channel references disclosed by steps 7.7 and 7.8 is typified by Figure 6. The separated Ro impact from the buoyancy effect on the heat transfer performances of a rotating channel is correlated as the Ro function to be a part of Nu/Nu0 correlation (Figure 6). The positive or negative &#968;2 values in Figure 6 indicate the improving or impeding effects on heat transfer performances due to buoyancy interactions. The larger &#968;2 magnitude, the higher degrees of rotating buoyancy impact are imposed on the heat transfer properties. The fitted lines indicated in Figure 6 are the plots of the correlative functions. The functional structures of the correlations for zero-buoyancy Nu/Nu0 ratios and &#968;2 values are generally determined in accordance with the varying manners of the data trends emerged in Figure 6. As discussed previously, the different channel geometries between the furrowed32 and pin-fin33 channels have respectively led to the negative and positive &#968;2 values in Figure 6. But the common feature of the reduced magnitudes of &#968;2 values caused by increasing Ro is observed for the two types of rotating channels32,33 in Figure 6. Having correlated the &#968;2 values and the Nu/Nu0 ratios at zero-buoyancy conditions into the Ro functions, the heat transfer correlations, which permit the evaluation of the isolated and coupled Ro and Bu effects on Nu/Nu0, is generated for the particular rotating channel.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/57630/57630fig1.jpg" /> 
Figure 1. Realistic operating Re, Ro and Bu ranges and the emulated laboratory conditions for a rotating coolant channel in a gas turbine rotor blade. The test conditions performed by NASA HOST program3,4,5,6 are indicated as the bar symbol. The open and solid symbols respectively signify the Bu, Ro, and Re test ranges for the pointed and full-field heat transfer measurements. Numbers in brackets are references from which data are taken. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/57630/57630fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/57630/57630fig2.jpg" /> 
Figure 2. Typical heat loss coefficients (hloss) at various rotating speeds30 using the trapezoidal twin-pass rib-roughened rotating channel as an illustrative example. The diagram at the top depicts the constructional details of the rotating test module. The slope of each data trend constituted by the heat loss flux against the wall-to-ambient temperature difference shown in the left lower portion reveals the heat loss coefficient at the specific rotating speed. By correlating the heat loss coefficients detected at all the rotating speed tested, the generated heat loss correlation typified by the right lower plot is incorporated into the data processing program for Nu accountancy. The error bars in the lower right plot indicate the ranges of hloss30. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/57630/57630fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/57630/57630fig3.jpg" /> 
Figure 3. Local Nusselt number distribution of the static twin-pass S-channel roughened by curly ribs at Re = 15,000 measured by present infrared thermography method. The top diagram depicts the endwall of the two-pass wavy channel and the longitudinal S-ribs. As indicated by the AA&#8217; section view, the pair of longitudinal S-ribs is arranged inline on two opposite channel endwalls. In the detailed distribution of Nusselt number over the two-pass wavy endwall shown as the lower plot, the Nu data along the two longitudinal S-ribs are discarded due to the wall conduction effects on the distributions of heat-flux and wall-temperature. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/57630/57630fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/57630/57630fig4.jpg" /> 
Figure 4. Examples demonstrating the isolation of Re impact from Ro and Bu effect on local and regionally-averaged heat transfer properties of rotating channel. The upper portion exhibits the detailed Nusselt number distributions at a fixed Ro of 0.15 with a different Re of 5000, 7500, and 12,500 to enlighten the impacts of Reynolds number on the heat transfer properties of the rotating endwall. The lower portion depicted the area-averaged heat transfer properties over the rotational leading and trailing endwalls. The normalized Nu/Nu0 ratios highlight the heat transfer variations from the non-rotating scenarios by rotation. Adapted with permission from Chang et al. 201731. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/57630/57630fig4large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/57630/57630fig5.jpg" /> 
Figure 5. Examples demonstrating the uncoupled Ro effect from Bu impact on heat transfer properties of rotating channel32,33. Each Bu-driven Nu/Nu0 variation is obtained at the fixed Ro and correlated as a linear function of Bu as indicated by the straight line in each plot. The correlation coefficients of these fitted lines fall between 0.96 and 0.98. The extrapolation of the Nu/Nu0 data trend toward Bu&#8594;0 along each fitted line reveals the Nu/Nu0 ratio at the tested Ro. The magnitude and slope of each Bu-driven Nu/Nu0 data trend disclose the manners of buoyancy effect on heat transfer performances. The magnitudes of the slopes represent the degrees of Bu impact on Nu/Nu0. The positive and negative slopes respectively reflect the improving and impairing buoyancy impact on heat transfer levels. Numbers in brackets are references from which data are taken. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/57630/57630fig5large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 6" class="xfigimg" src="/files/ftp_upload/57630/57630fig6.jpg" /> 
Figure 6. Uncoupled Ro and Bu effects on regionally averaged heat transfer performances of the rotating wavy channel32,33. The upper portion collects the heat transfer scenarios at various Ro but with vanished buoyancy effect at Bu = 0. Such Nu/Nu0 variations are solely caused by the various Coriolis forces at different Ro. The lower portion shows the variations of Bu impact on Nu/Nu0 at different Ro. The negative and positive &#968;2 values indicate the respective impairing and improving Bu impacts on the heat transfer performances for the furrowed32 and pin-fin33 channels. The dotted lines in this Figure are the correlation results for Nu/Nu0 at Bu = 0. Numbers in brackets are references from which data are taken. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/57630/57630fig6large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel at JoVE.com

Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel

Here, we present an experimental method for decoupling the interdependent Coriolis-force and rotating-buoyancy effects on full-field heat transfer distributions of a rotating channel.

An experimental method for exploring the heat transfer characteristics of an axially rotating channel is proposed. The governing flow parameters that ...

uncoupling-coriolis-force-rotating-buoyancy-effects-on-full-field

Nanyang Technological University

Education

Research

JoVE Core

JoVE Journal

Physics

Civil Engineering

Mechanical Engineering

Engineering

Unit 1

Equilibrium of a Rigid Body

Open Channel Flow

Dynamics of Rotational Motions

SCIENTISTS IN ACTION

8.1K Views.  National Cheng Kung University. Here, we present an experimental method for decoupling the interdependent Coriolis-force and rotating-buoyancy effects on full-field heat transfer distributions of a rotating channel.

Video: Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel

Proton Transfer and Protein Conformation Dynamics in Photosensitive Proteins by Time-resolved Step-scan Fourier-transform Infrared Spectroscopy

Monitoring the dynamics of protonation and protein backbone conformation changes during the function of a protein is an essential step towards understanding its mechanism. Protonation and conformational changes affect the vibration pattern of amino acid side chains and of the peptide bond, respectively, both of which can be probed by infrared (IR) difference spectroscopy. For proteins whose function can be repetitively and reproducibly triggered by light, it is possible to obtain infrared difference spectra with (sub)microsecond resolution over a broad spectral range using the step-scan Fourier transform infrared technique. With ~102-103 repetitions of the photoreaction, the minimum number to complete a scan at reasonable spectral resolution and bandwidth, the noise level in the absorption difference spectra can be as low as ~10-4, sufficient to follow the kinetics of protonation changes from a single amino acid. Lower noise levels can be accomplished by more data averaging and/or mathematical processing. The amount of protein required for optimal results is between 5-100 &#181;g, depending on the sampling technique used. Regarding additional requirements, the protein needs to be first concentrated in a low ionic strength buffer and then dried to form a film. The protein film is hydrated prior to the experiment, either with little droplets of water or under controlled atmospheric humidity. The attained hydration level (g of water / g of protein) is gauged from an IR absorption spectrum. To showcase the technique, we studied the photocycle of the light-driven proton-pump bacteriorhodopsin in its native purple membrane environment, and of the light-gated ion channel channelrhodopsin-2 solubilized in detergent.

Key steps of protein function, in particular backbone conformational changes and proton transfer reactions, often take place in the microsecond to millisecond time scale. These dynamical processes can be studied by time-resolved step-scan Fourier-transform infrared spectroscopy, in particular for proteins whose function is triggered by light.

Monitoring the dynamics of protonation and protein backbone conformation changes during the function of a protein is an essential step towards ...

Atomic Force Microscopy of Red-Light Photoreceptors Using PeakForce Quantitative Nanomechanical Property Mapping

Atomic force microscopy (AFM) uses a pyramidal tip attached to a cantilever to probe the force response of a surface. The deflections of the tip can be measured to ~10 pN by a laser and sectored detector, which can be converted to image topography. Amplitude modulation or &#8220;tapping mode&#8221; AFM involves the probe making intermittent contact with the surface while oscillating at its resonant frequency to produce an image. Used in conjunction with a fluid cell, tapping-mode AFM enables the imaging of biological macromolecules such as proteins in physiologically relevant conditions. Tapping-mode AFM requires manual tuning of the probe and frequent adjustments of a multitude of scanning parameters which can be challenging for inexperienced users. To obtain high-quality images, these adjustments are the most time consuming.
PeakForce Quantitative Nanomechanical Property Mapping (PF-QNM) produces an image by measuring a force response curve for every point of contact with the sample. With ScanAsyst software, PF-QNM can be automated. This software adjusts the set-point, drive frequency, scan rate, gains, and other important scanning parameters automatically for a given sample. Not only does this process protect both fragile probes and samples, it significantly reduces the time required to obtain high resolution images. PF-QNM is compatible for AFM imaging in fluid; therefore, it has extensive application for imaging biologically relevant materials.
The method presented in this paper describes the application of PF-QNM to obtain images of a bacterial red-light photoreceptor, RpBphP3 (P3), from photosynthetic R. palustris in its light-adapted state. Using this method, individual protein dimers of P3 and aggregates of dimers have been observed on a mica surface in the presence of an imaging buffer. With appropriate adjustments to surface and/or solution concentration, this method may be generally applied to other biologically relevant macromolecules and soft materials.

A method for investigating the structure of a protein photoreceptor using atomic force microscopy (AFM) is described in this paper. PeakForce Quantitative Nanomechanical Property Mapping (PF-QNM) reveals intact protein dimers on a mica surface.

Atomic force microscopy (AFM) uses a pyramidal tip attached to a cantilever to probe the force response of a surface. The deflections of the tip can be ...

Electroactive Polymer Nanoparticles Exhibiting Photothermal Properties

A method for the synthesis of electroactive polymers is demonstrated, starting with the synthesis of extended conjugation monomers using a three-step process that finishes with Negishi coupling. Negishi coupling is a cross-coupling process in which a chemical precursor is first lithiated, followed by transmetallation with ZnCl2. The resultant organozinc compound can be coupled to a dibrominated aromatic precursor to give the conjugated monomer. Polymer films can be prepared via electropolymerization of the monomer and characterized using cyclic voltammetry and ultraviolet-visible-near infrared (UV-Vis-NIR) spectroscopy. Nanoparticles (NPs) are prepared via emulsion polymerization of the monomer using a two-surfactant system to yield an aqueous dispersion of the polymer NPs. The NPs are characterized using dynamic light scattering, electron microscopy, and UV-Vis-NIR-spectroscopy. Cytocompatibility of NPs is investigated using the cell viability assay. Finally, the NP suspensions are irradiated with a NIR laser to determine their effectiveness as potential materials for photothermal therapy (PTT).

A protocol is presented for the synthesis and preparation of nanoparticles consisting of electroactive polymers.

A method for the synthesis of electroactive polymers is demonstrated, starting with the synthesis of extended conjugation monomers using a three-step ...

Laser-induced Forward Transfer of Ag Nanopaste

Over the past decade, there has been much development of non-lithographic methods1-3 for printing metallic inks or other functional materials. Many of these processes such as inkjet3 and laser-induced forward transfer (LIFT)4 have become increasingly popular as interest in printable electronics and maskless patterning has grown. These additive manufacturing processes are inexpensive, environmentally friendly, and well suited for rapid prototyping, when compared to more traditional semiconductor processing techniques. While most direct-write processes are confined to two-dimensional structures and cannot handle materials with high viscosity (particularly inkjet), LIFT can transcend both constraints if performed properly. Congruent transfer of three dimensional pixels (called voxels), also referred to as laser decal transfer (LDT)5-9, has recently been demonstrated with the LIFT technique using highly viscous Ag nanopastes to fabricate freestanding interconnects, complex voxel shapes, and high-aspect-ratio structures. In this paper, we demonstrate a simple yet versatile process for fabricating a variety of micro- and macroscale Ag structures. Structures include simple shapes for patterning electrical contacts, bridging and cantilever structures, high-aspect-ratio structures, and single-shot, large area transfers using a commercial digital micromirror device (DMD) chip.

We demonstrate the use of the Laser-induced forward transfer technique (LIFT) for the printing of high-viscosity Ag paste. This technique offers a simple, low temperature, robust process for non-lithographically printing microscale 2D and 3D structures.

Over the past decade, there has been much development of non-lithographic methods1-3 for printing metallic inks or other functional materials. Many of ...

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine

We demonstrate a method for the study of the heat and mass transfer and of the freezing phenomena in a subcooled brine environment. Our experiment showed that, under the proper conditions, ice can be produced when water is introduced to a bath of cold brine. To make ice form, in addition to having the brine and water mix, the rate of heat transfer must bypass that of mass transfer. When water is introduced in the form of tiny droplets to the brine surface, the mode of heat and mass transfer is by diffusion. The buoyancy stops water from mixing with the brine underneath, but as the ice grows thicker, it slows down the rate of heat transfer, making ice more difficult to grow as a result. When water is introduced inside the brine in the form of a flow, a number of factors are found to influence how much ice can form. Brine temperature and concentration, which are the driving forces of heat and mass transfer, respectively, can affect the water-to-ice conversion ratio; lower bath temperatures and brine concentrations encourage more ice to form. The flow rheology, which can directly affect both the heat and mass transfer coefficients, is also a key factor. In addition, the flow rheology changes the area of contact of the flow with the bulk fluid.

Here, we present a protocol to demonstrate the generation of ice when water is introduced to a cold bath of brine, as a secondary refrigerant, at a range of temperatures well below the freezing point of water. It can be used as an alternative way of producing ice for industry.

We demonstrate a method for the study of the heat and mass transfer and of the freezing phenomena in a subcooled brine environment. Our experiment showed ...

Magnetically Induced Rotating Rayleigh-Taylor Instability

Classical techniques for investigating the Rayleigh-Taylor instability include using compressed gasses1, rocketry2 or linear electric motors3 to reverse the effective direction of gravity, and accelerate the lighter fluid toward the denser fluid. Other authorse.g. 4,5,6 have separated a gravitationally unstable stratification with a barrier that is removed to initiate the flow. However, the parabolic initial interface in the case of a rotating stratification imposes significant technical difficulties experimentally. We wish to be able to spin-up the stratification into solid-body rotation and only then initiate the flow in order to investigate the effects of rotation upon the Rayleigh-Taylor instability. The approach we have adopted here is to use the magnetic field of a superconducting magnet to manipulate the effective weight of the two liquids to initiate the flow. We create a gravitationally stable two-layer stratification using standard flotation techniques. The upper layer is less dense than the lower layer and so the system is Rayleigh-Taylor stable. This stratification is then spun-up until both layers are in solid-body rotation and a parabolic interface is observed. These experiments use fluids with low magnetic susceptibility, |&#967;| ~ 10-6 - 10-5, compared to a ferrofluids. The dominant effect of the magnetic field applies a body-force to each layer changing the effective weight. The upper layer is weakly paramagnetic while the lower layer is weakly diamagnetic. When the magnetic field is applied, the lower layer is repelled from the magnet while the upper layer is attracted towards the magnet. A Rayleigh-Taylor instability is achieved with application of a high gradient magnetic field. We further observed that increasing the dynamic viscosity of the fluid in each layer, increases the length-scale of the instability.

We present a protocol for preparing a two-layer density-stratified liquid that can be spun-up into solid body rotation and subsequently induced into Rayleigh-Taylor instability by applying a gradient magnetic field.

Classical techniques for investigating the Rayleigh-Taylor instability include using compressed gasses1, rocketry2 or linear electric motors3 to reverse ...

Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source

Silicon photonic chips have the potential to realize complex integrated quantum information processing circuits, including photon sources, qubit manipulation, and integrated single-photon detectors. Here, we present the key aspects of preparing and testing a silicon photonic quantum chip with an integrated photon source and two-photon interferometer. The most important aspect of an integrated quantum circuit is minimizing loss so that all of the generated photons are detected with the highest possible fidelity. Here, we describe how to perform low-loss edge coupling by using an ultra-high numerical aperture fiber to closely match the mode of the silicon waveguides. By using an optimized fusion splicing recipe, the UHNA fiber is seamlessly interfaced with a standard single-mode fiber. This low-loss coupling allows the measurement of high-fidelity photon production in an integrated silicon ring resonator and the subsequent two-photon interference of the produced photons in a closely integrated Mach-Zehnder interferometer. This paper describes the essential procedures for the preparation and characterization of high-performance and scalable silicon quantum photonic circuits.

Silicon photonic chips have the potential to realize complex integrated quantum systems. Presented here is a method for preparing and testing a silicon photonic chip for quantum measurements.

Silicon photonic chips have the potential to realize complex integrated quantum information processing circuits, including photon sources, qubit ...

Pool-Boiling Heat-Transfer Enhancement on Cylindrical Surfaces with Hybrid Wettable Patterns

In this study, pool-boiling heat-transfer experiments were performed to investigate the effect of the number of interlines and the orientation of the hybrid wettable pattern. Hybrid wettable patterns were produced by coating superhydrophilic SiO2 on a masked, hydrophobic, cylindrical copper surface. Using de-ionized (DI) water as the working fluid, pool-boiling heat-transfer studies were conducted on the different surface-treated copper cylinders of a 25-mm diameter and a 40-mm length. The experimental results showed that the number of interlines and the orientation of the hybrid wettable pattern influenced the wall superheat and the HTC. By increasing the number of interlines, the HTC was enhanced when compared to the plain surface. Images obtained from the charge-coupled device (CCD) camera indicated that more bubbles formed on the interlines as compared to other parts. The hybrid wettable pattern with the lowermost section being hydrophobic gave the best heat-transfer coefficient (HTC). The experimental results indicated that the bubble dynamics of the surface is an important factor that determines the nucleate boiling.

Pool-boiling heat-transfer experiments were carried out to observe the effects of hybrid wettable patterns on the heat-transfer coefficient (HTC). The parameters of investigation are the number of interlines and the pattern orientation of the modified wettable surface.

In this study, pool-boiling heat-transfer experiments were performed to investigate the effect of the number of interlines and the orientation of the ...

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

This manuscript provides step by step description of the manufacturing process of a test section designed to measure the local instantaneous heat transfer coefficient as a function of the liquid flow rate in a transparent pipe. With certain amendments, the approach is extended to gas-liquid flows, with a particular emphasis on the effect of a single elongated (Taylor) air bubble on heat transfer enhancement. A non-invasive thermography technique is applied to measure the instantaneous temperature of a thin metal foil heated electrically. The foil is glued to cover a narrow slot cut in the pipe. The thermal inertia of the foil is small enough to detect the variation in the instantaneous foil temperature. The test section can be moved along the pipe and is long enough to cover a considerable part of the growing thermal boundary layer.
At the beginning of each experimental run, a steady state with a constant water flow rate and heat flux to the foil is attained and serves as the reference. The Taylor bubble is then injected into the pipe. The heat transfer coefficient variations due to the passage of a Taylor bubble propagating in a vertical pipe is measured as function of the distance of the measuring point from the bottom of the moving Taylor bubble. Thus, the results represent the local heat transfer coefficients. Multiple independent runs preformed under identical conditions allow accumulating sufficient data to calculate reliable ensemble-averaged results on the transient convective heat transfer. In order to perform this in a frame of reference moving with the bubble, the location of the bubble along the pipe has to be known at all times. Detailed description of measurements of the length and of the translational velocity of the Taylor bubbles by optical probes is presented.

This manuscript describes methods aimed at measuring the local instantaneous convective heat transfer coefficients in a single or two-phase pipe flow. A simple optical method to determine the length and the propagation velocity of an elongated (Taylor) air bubble moving at a constant velocity is also presented.

This manuscript provides step by step description of the manufacturing process of a test section designed to measure the local instantaneous heat transfer ...

Measurement of Dynamic Force Acted on Water Strider Leg Jumping Upward by the PVDF Film Sensor

This study aimed to make an explanation for the phenomenon in nature that water strider usually jumps or glides on the water surface easily but quickly, with its peak locomotion speed reaching 150 cm/s. First of all, we observed the microstructure and hierarchy of water strider legs using the scanning electron microscope. On the basis of the observed morphology of the legs, a theoretical model of the detachment from water surface was established, which explained water striders' capability to slide on water surface effortlessly in terms of energy reduction. Secondly, a dynamic force measurement system was devised using the PVDF film sensor with excellent sensitivity, which could detect the whole interaction process. Subsequently, a single leg in contact with water was pulled upward at different speeds, and the adhesion force was measured at the same time. The results of the departing experiment suggested a deep understanding of the fast jumping of water striders.

The protocol here is dedicated to investigating the free and quick maneuvering of water strider on water surface. The protocol includes observing the microstructure of legs and measuring the adhesion force when departing from water surface at different speeds.

This study aimed to make an explanation for the phenomenon in nature that water strider usually jumps or glides on the water surface easily but quickly, ...