This research was supported by the National Science Foundation (Awards CMMI-1437050 and DMR-1207342), the Office of Naval Research (Grant N00014-10-10489), and the Air Force Office of Scientific Research (Grant FA9550-14-1-0090).

1. Preparing Sr and Ti Precursors for ALD Experiments
<ol>
	<li>Load the clean, dry saturators and new precursors into the antechamber of a glove box. Follow the glove box&#39;s loading procedure to ensure proper purging of air and moisture. Transfer the materials into the main chamber. 
	Note: This group uses in-house built saturators (see Figure 3) with components purchased commercially. Details of the saturator assembly can be found in the List of Specific Reagents and Equipment.</li>
	<li>Store the strontium precursor (strontium bis(triisopropylcyclopentadienyl) [Sr(iPr3Cp)2]) and titanium precursor (titanium tetraisopropoxide [Ti(O-iPr)4], TTIP) in an inert environment (e.g., a glove box) after opening the original packaging provided by the manufacturer. 
	Note: This group uses a glovebox with a moisture level no greater than 5 ppm.</li>
	<li>Load the precursor into the saturator such that the precursor occupies approximately 2/3 of the glass part of the saturator (about 5 g).</li>
	<li>Reassemble the saturators and ensure a good leak tight seal is achieved. 
	Note: This group uses metal gasket face seal fittings to achieve leak tight seals.</li>
	<li>Unload the filled saturators from the glove box and connect the filled saturators to the ALD manifold. 
	Note: The loaded precursors can be used multiple times over an extended period. The precursors in this group&#39;s system generally require refilling every six months as they become consumed. Sr(iPr3Cp)2 is a brown liquid at both RT and the operating temperature for this study (130 - 140 &#176;C). TTIP is a clear liquid. When TTIP deteriorates, typically due to moisture and/or air contamination, the precursor will turn into a white solid. There has been no visible indicator of precursor deterioration for the Sr(iPr3Cp)2 observed by this group. Sr precursor deterioration is generally detected by a significant decrease (greater than 10%) of Sr content in a repeatable ALD growth that utilizes Sr(iPr3Cp)2.</li>
</ol>
2. Cleaning the Ge (001) Substrate
<ol>
	<li>Place a Ge (001) substrate (18 mm &#215; 20 mm), polished side facing upwards, into a small beaker (25-50 ml). Fill the beaker to about 1 cm height with acetone. Place the beaker in a bath sonicator and sonicate for 10 min. 
	Note: This group uses single-side polished 4-in Ge wafers, cut into 18 &#215; 20 mm2 pieces using a dicing saw. Use heavily doped n-type Ge if electrical measurements of the film are needed (this study uses Sb-doped Ge wafers with &#961; &#8776; 0.04 &#937;-cm), otherwise all doping level and dopant types are acceptable.</li>
	<li>Decant the majority of the acetone into a waste container, taking care not to pour out or flip the Ge substrate. Rinse the walls of the beaker with isopropyl alcohol (IPA) and fill to approximately 1 cm height. Pour the majority of the IPA into a waste container, refill beaker to 1 cm with IPA, and sonicate for another 10 min.</li>
	<li>Repeat step 2.2, but replace IPA with deionized water.</li>
	<li>Remove the substrate from the beaker with tweezers. Dry the substrate with a nitrogen gun or other dry inert gas flow.</li>
	<li>Place the substrate in the UV-ozone cleaner and run the cleaner for 30 min.</li>
	<li>After UV-ozone cleaning, immediately load the substrate into the vacuum system.</li>
</ol>
3. Loading the Ge Substrate
<ol>
	<li>Move the transfer line sample carrier-cart into the load lock. Close the gate-valve to isolate the load lock.</li>
	<li>Turn off the load lock turbomolecular pump and open the nitrogen line to vent the load lock. Complete Step 3.3 while waiting for the load lock to completely vent.</li>
	<li>Place the substrate, polished side facing downward, into a 20 mm &#215; 20 mm sample holder. 
	Note: All depositions are performed with the sample facing downward. Ensure the substrate is flush with the bottom of the holder; otherwise RHEED experiments may experience difficulty and films may not deposit uniformly. A sample holder this group uses is shown in Figure 4.</li>
	<li>Open the load lock after it has completely vented. Place the sample holder into an open carrier-cart position by aligning the tabs of the sample holder with the channels of the open cart position and lowering it into place.</li>
	<li>Close the load lock and turn on the load lock turbomolecular pump. Close the nitrogen line.</li>
	<li>Wait until the pressure in the load lock is approximately 5.0&#215;10-7 Torr before opening the load lock gate valve and moving the cart through the transfer line.</li>
</ol>
4. Ge Deoxidization
<ol>
	<li>Transfer the Ge substrate into the MBE chamber.</li>
	<li>Ramp the Ge substrate temperature to 550 &#176;C at 20 &#176;C&#8226;min-1 and then to 700 &#176;C at 10 &#176;C&#8226;min-1. After holding the sample at 700 &#176;C for 1 hr, cool the sample to 200 &#176;C with a 30 &#176;C&#8226;min-1 ramp rate.</li>
	<li>Use RHEED to confirm the 2&#215;1 reconstructed surface as described in Representative Results section.26,39</li>
	<li>Optional: Use XPS to ensure that the Ge (001) substrate is free of oxides (described in Section 8).</li>
</ol>
5. Thin Film ALD Growth of STO on Ge Substrate
<ol>
	<li>Adjust the ALD reactor temperature to 225 &#186;C.</li>
	<li>Heat Sr(iPr3Cp)2 to 130 &#176;C and TTIP to 40 &#176;C. Maintain water at RT (between 20 and 25 &#176;C). Regulate the water vapor flow into the ALD system via the needle valve attached to the saturator such that the dosing pressure of water is around 1 Torr. Maintain constant precursor temperatures throughout the deposition process.</li>
	<li>Transfer the sample in vacuo to the ALD reactor that has been preheated to 225 &#176;C and wait for 15 min for the sample to reach thermal equilibrium.</li>
	<li>Switch the exhaust port of the ALD reactor from the turbomolecular pump to the mechanical pump.</li>
	<li>Turn on the flow controller to allow the flow of inert gas (this group uses argon). Maintain an operating pressure of 1 Torr during the entire growth process.</li>
	<li>Set the unit cycle ratio of Sr to Ti to be 2:1. Set the unit cycles of Sr and Ti to a 2-sec dose of the Sr or Ti precursor, followed by a 15-sec argon purge, and then a 1-sec dose of water, followed by another 15-sec argon purge.</li>
	<li>Adjust the number of unit cycles to achieve the desirable thickness. Ensure that the ALD cycling sequence contains as little repetition of individual Sr or Ti unit cycles as possible. For example, a 2:3 Sr-to-Ti cycling sequence will achieve better results when executed as 1-Sr, 1-Ti, followed by 1-Sr, 2-Ti, rather than 2-Sr followed by 3-Ti. 
	Note: This group used 36 unit cycles to deposit a 2-nm thick STO film on Ge.</li>
	<li>Optional: Use XPS to verify the film composition (described in Section 8).</li>
</ol>
6. Annealing of STO Film
<ol>
	<li>Transfer the deposited sample in vacuo into the annealing chamber.</li>
	<li>Heat the sample to 650 &#176;C at a rate of 20 &#176;C&#8226;min-1 under UHV conditions (10-9- 10-8 Torr). Hold the temperature at 650 &#186;C for 5 min, and then cool the sample to 200 &#176;C at the same rate. 
	Note: Use RHEED to evaluate the annealing result, as described in the Representative Results section.26,39</li>
</ol>
7. Further Growth of STO
<ol>
	<li>Repeat Section 5.1 - 5.5.</li>
	<li>Set the unit cycle ratio to between 1:1 and 4:3. Maintain the same dosing/purging component within each unit cycle. Set the sequence according to the principles mentioned in Step 5.6.</li>
	<li>Adjust the number of unit cycles to achieve the intended thickness.</li>
	<li>Anneal the deposited film according to Section 6 of the Protocol.</li>
</ol>
8. XPS Measurements
<ol>
	<li>Load the sample into the XPS analytical chamber and turn on the X-ray source. Ensure all appropriate gates/doors are closed to prevent accidental X-ray exposure.</li>
	<li>Create a new scan by selecting the elements (binding energy ranges) desired for analysis, or select a pre-existing scan program. 
	Note: Binding energy ranges can be manually changed, if needed. Set other settings, such as pass energy, excitation energy, step energy, and step time to optimize the signal-to-noise ratio, but remain constant across all elemental scans to maintain comparability between elemental spectra. Table 1 shows the scan settings used by this group.</li>
	<li>Check if any charging is occurring on the substrate by observing the binding energy of a known element&#39;s peak, such as O 1s at 531 eV. 
	Note: Charging is occurring if the peak has shifted from its known value.</li>
	<li>Insert a flood gun into the XPS chamber and turn on the flood gun if charging is occurring. Adjust the flood gun energy output and distance from the sample so that the chosen peak is shifted back to its correct binding energy.</li>
	<li>Manipulate the stage position to maximize the area observed under a known element&#39;s peak (typically the O 1s peak at 531 eV).</li>
	<li>Run the XPS scan and collect the data.</li>
	<li>Turn off the X-ray source and remove the sample from the XPS.</li>
</ol>

<ol>
	<li>Phan, M. -. H., Yu, S. -. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Review+of+the+magnetocaloric+effect+in+manganite+materials.">Review of the magnetocaloric effect in manganite materials.</a> J. Magn. Magn. Mater. 308 (2), 325-340 (2007).</li><li>Serrate, D., Teresa, J. M. D., Ibarra, M. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Double+perovskites+with+ferromagnetism+above+room+temperature.">Double perovskites with ferromagnetism above room temperature.</a> J. Phys. Condens. Matter. 19 (2), 023201 (2007).</li><li>Cheng, J. -. G., Zhou, J. -. S., Goodenough, J. B., Jin, C. -. Q. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Critical+behavior+of+ferromagnetic+perovskite+ruthenates.">Critical behavior of ferromagnetic perovskite ruthenates.</a> Phys. Rev. B. 85 (18), 184430 (2012).</li><li>Ahn, C. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ferroelectricity+at+the+Nanoscale:+Local+Polarization+in+Oxide+Thin+Films+and+Heterostructures.">Ferroelectricity at the Nanoscale: Local Polarization in Oxide Thin Films and Heterostructures.</a> Science. 303 (5657), 488-491 (2004).</li><li>Catalan, G., Scott, J. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Physics+and+Applications+of+Bismuth+Ferrite.">Physics and Applications of Bismuth Ferrite.</a> Adv. Mater. 21 (24), 2463-2485 (2009).</li><li>Ramesh, R., Spaldin, N. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multiferroics:+progress+and+prospects+in+thin+films.">Multiferroics: progress and prospects in thin films.</a> Nat. Mater. 6 (1), 21-29 (2007).</li><li>Vrejoiu, I., Alexe, M., Hesse, D., G&#246;sele, U. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Functional+Perovskites+-+From+Epitaxial+Films+to+Nanostructured+Arrays.">Functional Perovskites - From Epitaxial Films to Nanostructured Arrays.</a> Adv. Funct. Mater. 18 (24), 3892-3906 (2008).</li><li>Jang, H. W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Metallic+and+Insulating+Oxide+Interfaces+Controlled+by+Electronic+Correlations.">Metallic and Insulating Oxide Interfaces Controlled by Electronic Correlations.</a> Science. 331 (6019), 886-889 (2011).</li><li>Hwang, H. Y., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Emergent+phenomena+at+oxide+interfaces.">Emergent phenomena at oxide interfaces.</a> Nat. Mater. 11 (2), 103-113 (2012).</li><li>Stemmer, S., Millis, A. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantum+confinement+in+oxide+quantum+wells.">Quantum confinement in oxide quantum wells.</a> MRS Bull. 38 (12), 1032-1039 (2013).</li><li>Stemmer, S., James Allen, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two-Dimensional+Electron+Gases+at+Complex+Oxide+Interfaces.">Two-Dimensional Electron Gases at Complex Oxide Interfaces.</a> Annu. Rev. Mater. Res. 44 (1), 151-171 (2014).</li><li>Biscaras, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Two-dimensional+superconductivity+at+a+Mott+insulator/band+insulator+interface+LaTiO3/SrTiO3.">Two-dimensional superconductivity at a Mott insulator/band insulator interface LaTiO3/SrTiO3.</a> Nat. Commun. 1, 89 (2010).</li><li>Dagotto, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Complexity+in+Strongly+Correlated+Electronic+Systems.">Complexity in Strongly Correlated Electronic Systems.</a> Science. 309 (5732), 257-262 (2005).</li><li>Jin, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Novel+Multifunctional+Properties+Induced+by+Interface+Effects+in+Perovskite+Oxide+Heterostructures.">Novel Multifunctional Properties Induced by Interface Effects in Perovskite Oxide Heterostructures.</a> Adv. Mater. 21 (45), 4636-4640 (2009).</li><li>McKee, R. A., Walker, F. J., Chisholm, M. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Crystalline+oxides+on+silicon:+the+first+five+monolayers.">Crystalline oxides on silicon: the first five monolayers.</a> Phys. Rev. Lett. 81 (14), 3014 (1998).</li><li>Warusawithana, M. P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Ferroelectric+Oxide+Made+Directly+on+Silicon.">A Ferroelectric Oxide Made Directly on Silicon.</a> Science. 324 (5925), 367-370 (2009).</li><li>Niu, G., Vilquin, B., Penuelas, J., Botella, C., Hollinger, G., Saint-Girons, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Heteroepitaxy+of+SrTiO3+thin+films+on+Si+(001)+using+different+growth+strategies:+Toward+substratelike+qualitya.">Heteroepitaxy of SrTiO3 thin films on Si (001) using different growth strategies: Toward substratelike qualitya.</a> J. Vac. Sci. Technol. B. 29 (4), 041207 (2011).</li><li>Yu, Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Advances+in+heteroepitaxy+of+oxides+on+silicon.">Advances in heteroepitaxy of oxides on silicon.</a> Thin Solid Films. 462-463, 51-56 (2004).</li><li>Yu, Z., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Epitaxial+oxide+thin+films+on+Si+(001).">Epitaxial oxide thin films on Si (001).</a> J. Vac. Sci. Technol. B. 18 (4), 2139-2145 (2000).</li><li>Demkov, A. A., Zhang, X. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Theory+of+the+Sr-induced+reconstruction+of+the+Si+(001)+surface.">Theory of the Sr-induced reconstruction of the Si (001) surface.</a> J. Appl. Phys. 103 (10), 103710 (2008).</li><li>Zhang, X., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Atomic+and+electronic+structure+of+the+Si/SrTiO3+interface.">Atomic and electronic structure of the Si/SrTiO3 interface.</a> Phys. Rev. B. 68 (12), 125323 (2003).</li><li>Ashman, C. R., F&#246;rst, C. J., Schwarz, K., Bl&#246;chl, P. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=First-principles+calculations+of+strontium+on+Si(001).">First-principles calculations of strontium on Si(001).</a> Phys. Rev. B. 69 (7), 075309 (2004).</li><li>Kamata, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=High-k/Ge+MOSFETs+for+future+nanoelectronics.">High-k/Ge MOSFETs for future nanoelectronics.</a> Mater. Today. 11 (1-2), 30-38 (2008).</li><li>Fischetti, M. V., Laux, S. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Band+structure,+deformation+potentials,+and+carrier+mobility+in+strained+Si,+Ge,+and+SiGe+alloys.">Band structure, deformation potentials, and carrier mobility in strained Si, Ge, and SiGe alloys.</a> J. Appl. Phys. 80 (4), 2234-2252 (1996).</li><li>Liang, Y., Gan, S., Wei, Y., Gregory, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+Sr+adsorption+on+stability+of+and+epitaxial+SrTiO3+growth+on+Si(001)+surface.">Effect of Sr adsorption on stability of and epitaxial SrTiO3 growth on Si(001) surface.</a> Phys. Status Solidi B. 243 (9), 2098-2104 (2006).</li><li>McDaniel, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Chemical+Route+to+Monolithic+Integration+of+Crystalline+Oxides+on+Semiconductors.">A Chemical Route to Monolithic Integration of Crystalline Oxides on Semiconductors.</a> Adv. Mater. Interfaces. 1 (8), (2014).</li><li>Leskel&#228;, M., Ritala, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Atomic+layer+deposition+(ALD):+from+precursors+to+thin+film+structures.">Atomic layer deposition (ALD): from precursors to thin film structures.</a> Thin Solid Films. 409 (1), 138-146 (2002).</li><li>George, S. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Atomic+Layer+Deposition:+An+Overview.">Atomic Layer Deposition: An Overview.</a> Chem. Rev. 110 (1), 111-131 (2010).</li><li>McDaniel, M. D., Posadas, A., Wang, T., Demkov, A. A., Ekerdt, J. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Growth+and+characterization+of+epitaxial+anatase+TiO2(001)+on+SrTiO3-buffered+Si(001)+using+atomic+layer+deposition.">Growth and characterization of epitaxial anatase TiO2(001) on SrTiO3-buffered Si(001) using atomic layer deposition.</a> Thin Solid Films. 520 (21), 6525-6530 (2012).</li><li>McDaniel, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Growth+of+epitaxial+oxides+on+silicon+using+atomic+layer+deposition:+Crystallization+and+annealing+of+TiO2+on+SrTiO3-buffered+Si(001).">Growth of epitaxial oxides on silicon using atomic layer deposition: Crystallization and annealing of TiO2 on SrTiO3-buffered Si(001).</a> J. Vac. Sci. Technol. B. 30 (4), 04E11 (2012).</li><li>McDaniel, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Epitaxial+strontium+titanate+films+grown+by+atomic+layer+deposition+on+SrTiO3-buffered+Si(001)+substrates.">Epitaxial strontium titanate films grown by atomic layer deposition on SrTiO3-buffered Si(001) substrates.</a> J. Vac. Sci. Technol. A. 31 (1), 01A136 (2013).</li><li>Ngo, T. Q., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Epitaxial+growth+of+LaAlO3+on+SrTiO3-buffered+Si+(001)+substrates+by+atomic+layer+deposition.">Epitaxial growth of LaAlO3 on SrTiO3-buffered Si (001) substrates by atomic layer deposition.</a> J. Cryst. Growth. 363, 150-157 (2013).</li><li>Ngo, T. Q., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Epitaxial+c-axis+oriented+BaTiO3+thin+films+on+SrTiO3-buffered+Si(001)+by+atomic+layer+deposition.">Epitaxial c-axis oriented BaTiO3 thin films on SrTiO3-buffered Si(001) by atomic layer deposition.</a> Appl. Phys. Lett. 104 (8), 082910 (2014).</li><li>McDaniel, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Incorporation+of+La+in+epitaxial+SrTiO3+thin+films+grown+by+atomic+layer+deposition+on+SrTiO3-buffered+Si+(001)+substrates.">Incorporation of La in epitaxial SrTiO3 thin films grown by atomic layer deposition on SrTiO3-buffered Si (001) substrates.</a> J. Appl. Phys. 115 (22), 224108 (2014).</li><li>McDaniel, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Atomic+layer+deposition+of+crystalline+SrHfO3+directly+on+Ge+(001)+for+high-k+dielectric+applications.">Atomic layer deposition of crystalline SrHfO3 directly on Ge (001) for high-k dielectric applications.</a> J. Appl. Phys. 117 (5), 054101 (2015).</li><li>Jahangir-Moghadam, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Band-Gap+Engineering+at+a+Semiconductor-Crystalline+Oxide+Interface.">Band-Gap Engineering at a Semiconductor-Crystalline Oxide Interface.</a> Adv. Mater. Interfaces. 2 (4), (2015).</li><li>Posadas, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Epitaxial+integration+of+ferromagnetic+correlated+oxide+LaCoO3+with+Si+(100).">Epitaxial integration of ferromagnetic correlated oxide LaCoO3 with Si (100).</a> Appl. Phys. Lett. 98 (5), 053104 (2011).</li><li>Ponath, P., Posadas, A. B., Hatch, R. C., Demkov, A. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preparation+of+a+clean+Ge(001)+surface+using+oxygen+plasma+cleaning.">Preparation of a clean Ge(001) surface using oxygen plasma cleaning.</a> J. Vac. Sci. Technol. B. 31 (3), 031201 (2013).</li><li>Braun, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Applied RHEED: Reflection High-Energy Electron Diffraction During Crystal Growth. , (1999).</li><li>Moulder, J. F., Stickle, W. F., Sobol, P. E., Bomben, K. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Handbook of X-ray Photoelectron Spectroscopy. , (1992).</li><li>Vehkam&#228;ki, M., Hatanp&#228;&#228;, T., H&#228;nninen, T., Ritala, M., Leskel&#228;, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Growth+of+SrTiO3+and+BaTiO3+thin+films+by+atomic+layer+deposition.">Growth of SrTiO3 and BaTiO3 thin films by atomic layer deposition.</a> Electrochem. Solid-State Lett. 2 (10), 504-506 (1999).</li><li>Vehkam&#228;ki, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Atomic+Layer+Deposition+of+SrTiO3+Thin+Films+from+a+Novel+Strontium+Precursor-Strontium-bis(tri-isopropyl+cyclopentadienyl).">Atomic Layer Deposition of SrTiO3 Thin Films from a Novel Strontium Precursor-Strontium-bis(tri-isopropyl cyclopentadienyl).</a> Chem. Vap. Depos. 7 (2), 75-80 (2001).</li><li>Ritala, M., Leskel&#228;, M., Niinisto, L., Haussalo, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Titanium+isopropoxide+as+a+precursor+in+atomic+layer+epitaxy+of+titanium+dioxide+thin+films.">Titanium isopropoxide as a precursor in atomic layer epitaxy of titanium dioxide thin films.</a> Chem. Mater. 5 (8), 1174-1181 (1993).</li><li>Aarik, J., Aidla, A., Uustare, T., Ritala, M., Leskel&#228;, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Titanium+isopropoxide+as+a+precursor+for+atomic+layer+deposition:+characterization+of+titanium+dioxide+growth+process.">Titanium isopropoxide as a precursor for atomic layer deposition: characterization of titanium dioxide growth process.</a> Appl. Surf. Sci. 161 (3-4), 385-395 (2000).</li><li>Premkumar, P. A., Delabie, A., Rodriguez, L. N. J., Moussa, A., Adelmann, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Roughness+evolution+during+the+atomic+layer+deposition+of+metal+oxides.">Roughness evolution during the atomic layer deposition of metal oxides.</a> J. Vac. Sci. Technol. A. 31 (6), 061501 (2013).</li></ol>

The authors have no competing financial interests to disclose.

The cleanliness of the Ge substrate is the key to success when growing the epitaxial perovskite using ALD. The amount of time a Ge substrate spends between degreasing and deoxidization, and the amount of time between deoxidization and STO deposition, should be kept at a minimum. Samples are still subject to contaminant exposure even under the UHV environment. Prolonged exposure may lead to redeposition of adventitious carbon or Ge reoxidation, resulting in poor film growth. This group has employed a widely-used degreasing procedure (sonication in acetone/IPA/DI-water with subsequent UV-ozone exposure) to remove the carbon contaminants. Another procedure using oxygen plasma under UHV conditions can also be used to remove carbon contaminants.39 The oxygen plasma will also oxidize the surface of the Ge substrate, but the oxide can be removed in a subsequent Ge deoxidization protocol. The thermal deoxidation of the GeO2 protocol presented here is effective for the purposes of the perovskite growth in this study.
In addition to the cleanliness of the substrate, it is imperative to achieve the slightly Sr-rich stoichiometry, ideally between 0.53 and 0.54 Sr/(Sr+Ti), in order to achieve crystallization during the annealing step. While films with Sr/(Sr+Ti) of between 0.48 and 0.57 can all crystallize to various extents, this group has experimentally found that STO films with Sr/(Sr+Ti) between 0.53 and 0.54 crystallize most easily. That is, onset crystallization can be observed at a lower temperature during temperature ramping (Step 6.2) than films with other compositions. The stoichiometry between Sr and Ti is determined by various parameters of the deposition process, such as precursor temperature, dosing and purging time, substrate temperature, and unit cycle ratio. The selection of these parameters largely depends on the reaction kinetics of each ALD precursor. Enough precursor vapor pressure is needed in the reactor chamber to drive the equilibrium toward complete surface coverage and adsorption of precursor molecules. A suitable precursor temperature and dosing time will ensure a precursor saturates the substrate surface during the dosing step of an ALD unit cycle. The precursor temperature employed in an ALD experiment is determined by reviewing a combination of reports in the literature, manufacturers&#39; specifications, and previous experimental experience with the compounds. This group typically adjusts the precursor temperature such that the precursor vapor pressure is approximately 0.1 Torr. Due to the variation between different deposition system designs, some trial-and-error is generally needed to find the precursor temperature when adopting a new precursor. Similarly, sufficient purging time is required such that the ALD chamber is free of the previously-dosed precursor molecules. This ensures a true ALD process-depositing one material at a time rather than a CVD-like continuous deposition. ALD precursors also possess temperature windows (the &#34;ALD window&#34;) where the deposition rate will be nearly independent of the substrate temperature. During deposition the precursor molecules will saturate the substrate surface, preventing additional molecules from adsorbing onto the surface. As a result, the amount of molecules-and atoms-deposited every cycle will be limited by the reactant adsorption properties and kinetics. For a ternary oxide like STO, the two precursors may still have different rates of deposition. Hence, the unit cycle ratio between the precursors needs to be established experimentally. This group has settled on the parameters mentioned in Sections 5 to 7 in the Protocol section via product specifications from manufacturers, reports from literature,42-45 and data from past experiments.29,30
It was found through experiments that even though Sr:Ti cycle ratios of near 1:1 yielded stoichiometric STO films on STO-buffered Si (001), a 2:1 Sr:Ti cycle ratio is needed for the initial STO growth on Ge.26 As a result, a two-step ALD growth is used for STO films thicker than 2 nm. The STO films deposited using Steps 5 to 7 of the Protocol will be amorphous as-deposited and it is necessary to anneal the films. The annealing temperature is established experimentally.26,29,30, The need for annealing temperatures higher than 650 &#176;C may indicate problems with the substrate, such as an incompletely cleaned substrate surface or stoichiometry deviating from ideal to slightly Sr-rich stoichiometry (e.g., ideal SrTiO3 has 20, 20, and 60 atomic% of Sr, Ti, and O, respectively). Although the theoretical perovskite stoichiometry should yield the best possible crystallinity, slightly A-rich films were observed to crystallize better than stoichiometric or B-rich films. If the ratio of Sr/(Sr+Ti) is beyond the range of 0.48 to 0.57, it will be hard to crystallize the film during the annealing process. This group has annealed STO films in the MBE chamber equipped with in situ RHEED to monitor the process of crystallization, and thus decided the parameters for the annealing procedure.
After the completion of Sections 4, 5, 6, and 7 of the Protocol, one will have the option of evaluating the sample via XPS. This group used in situ XPS for all the XPS measurements discussed in this article, i.e., the samples remained in the UHV system at all times. The use of in situ XPS allows for accurate evaluation of the result after each step of the experiment. Therefore, the carbon content-a common contaminant in ALD-in the deposited film can be evaluated without concerns for contamination from ambient carbon sources. The samples were also not exposed to an oxidative atmosphere after growth, which eliminates the possibility of altering film properties via oxidation.
Although the stoichiometric ratio between Sr and Ti in the deposited STO film can be adjusted by manipulating the unit cycle ratio, the stoichiometric ratio may not vary linearly with respect to the ratio between the two precursors. STO films, among other perovskites, are more tolerant toward Ti deficiency (B-site vacancies of the perovskite) as opposed to that of Sr (A-site).26,31,33 A good stoichiometry (between 0.53 and 0.54 Sr/(Sr+Ti)) will result in a lower crystallization temperature during annealing. Using the prescribed protocol, this group has grown stoichiometric, crystalline STO films of up to 15 nm in thickness.26 To grow a thicker film, one might need to deposit the film in multiple growth-and-anneal steps, or try to promote in situ crystallization. With a higher deposition temperature, the film may crystallize upon deposition. A drawback of promoting in situ crystallization is that the roughness of the films seems to be greater than those films crystallized by annealing an amorphous film after deposition.46
The ALD of STO on Ge experiment discussed in this article may be easily modified to deposit A-site and B-site substituted perovskite films. This can be done by substituting some of the Sr or Ti unit cycles with those of desirable elements, such as lanthanum for the A-site and hafnium for the B-site. It is also possible to apply the principles behind this protocol when growing other ABO3 perovskite films, such as strontium hafnate (SHO)35 and barium titanate (BTO),36 epitaxially on Ge (001). The various properties of lattice-matched perovskite oxides provide will enable the development of monolithically integrated perovskite-based microelectronic devices. This work has demonstrated the potential of growing crystalline oxides for the application of advanced electronic applications in the near future, especially for high-mobility semiconductor materials such as Ge.

Perovskite materials are becoming increasingly attractive due to their highly symmetric cubic or pseudocubic structure and myriad of properties. These materials, with general formula ABO3, consist of A atoms coordinated with 12 oxygen atoms and B atoms coordinated with six oxygen atoms. Owing to their simple structure, yet wide range of potential elements, perovskite materials provide ideal candidates for heterostructure devices. Epitaxial oxide heterostructures boast ferromagnetic,1-3 anti/ferroelectric,4 multiferroic,5-8 superconductive,7-12 and magnetoresistive functionalities.13,14 Many of these desirable electronic properties are interfacial and thus dependent on clean, abrupt transitions between materials. The nearly identical structure and lattice constants shared between members of the perovskite family allow for excellent lattice matching and, therefore, high quality interfaces. Readily lattice-matched to each other as well as some semiconductors, perovskite oxides are now being turned to in next generation metal-oxide-semiconductor electronics.
Monolithic integration of crystalline oxides with silicon, first demonstrated with perovskite strontium titanate, SrTiO3 (STO), by McKee and colleagues,15 was a monumental step towards the realization of electronic devices with perovskite-semiconductor incorporation. Molecular beam epitaxy (MBE) is the primary technique for epitaxial growth of oxides on silicon because of the layer-by-layer growth as well as the tunable oxygen partial pressure necessary to control amorphous, interfacial SiO2 formation.16-19 Typical MBE growth of STO on Si (001) is achieved by Sr-assisted deoxidation of SiO2. Under the ultra-high vacuum (UHV) conditions, SrO is volatile and subject to thermal evaporation. Since SrO is thermodynamically preferred over strontium metal and SiO2, deposition of Sr scavenges oxygen from the SiO2 layer and the resulting SrO evaporates from the surface. During this process the silicon surface experiences a 2&#215;1 reconstruction at the surface that forms rows of dimerized silicon atoms. Conveniently, &#189; monolayer (ML) coverage of Sr atoms on the reconstructed surface fills in the gaps created by these dimer rows.20 The &#189; ML coverage provides a protective layer that, with careful control of oxygen pressure, can prevent or control interfacial SiO2 formation during subsequent oxide growth.21-23 In the case of STO (and perovskites with similar lattice match), the resulting lattice is rotated 45&#176; in-plane such that (001)STO&#8214;(001)Si and (100)STO&#8214;(110)Si, allowing registry between the Si (3.84 &#197; Si-Si distance) and STO (a = 3.905 &#197;) with only slight compressive strain on the STO. This registry is necessary for high quality interfaces and the desired properties they possess.
Silicon became industrially significant due to the high quality of its interfacial oxide, but SiO2 use is being phased out for materials capable of equivalent performance at smaller feature sizes. SiO2 experiences high leakage currents when ultra-thin and this diminishes device performance. The demand for smaller feature sizes could be met by perovskite oxide films with high dielectric constants, k, that provide performance equivalent to SiO2 and are physically thicker than SiO2 by the factor k/3.9. Furthermore, alternative semiconductors, like germanium, offer potential for faster device operation due to higher electron and hole mobilities than silicon.24,25 Germanium also has an interfacial oxide, GeO2, but in contrast to SiO2, it is unstable and subject to thermal deoxidation. Thus, 2&#215;1 reconstruction is achievable by simple thermal annealing under UHV, and a protective Sr layer is unnecessary to prevent interfacial oxide growth during perovskite deposition.26
Despite the apparent ease of growth offered by MBE, atomic layer deposition (ALD) provides a more scalable and cost effective method than MBE for the commercial production of oxide materials.27,28 ALD employs doses of gaseous precursors to the substrate that are self-limiting in their reaction with the substrate surface. Therefore, in an ideal ALD process, up to one atomic layer is deposited for any given precursor dosing cycle and continued dosing of the same precursor will not deposit additional material onto the surface. Reactive functionality is restored with a co-reactant, often an oxidative or reductive precursor (e.g., water or ammonia). Previous work has demonstrated the ALD growth of various perovskite films, such as anatase TiO2, SrTiO3, BaTiO3, and LaAlO3, on Si (001) that had been buffered with four-unit-cell thick STO grown via MBE. 29-34 In purely MBE growth of crystalline oxides, &#189; monolayer coverage of Sr on clean Si (001) is enough to provide a barrier against SiO2 formation under the pressures native to the technique (~10-7 Torr). However, under typical ALD operating pressures of ~1 Torr, previous work has shown that four unit cells of STO is required to avoid oxidizing the Si surface.29
The procedure detailed here utilizes the instability of GeO2 and achieves monolithic integration of STO on germanium via ALD without the need of an MBE-grown buffer layer.26 Furthermore, the Ge-Ge interatomic distance (3.992 &#197;) on its (100) surface allows for an analogous epitaxial registry with STO that is observed with Si (001). Though the procedure presented here is specific to STO on Ge, slight modifications may allow for the monolithic integration of a variety of perovskite films on germanium. Indeed, direct ALD growth of crystalline SrHfO3 and BaTiO3 films have been reported on Ge.35,36 Additional possibilities include the potential gate oxide, SrZrxTi1-xO3.37 Finally, building on previous studies of ALD perovskite growth on a four-unit cell STO film on Si (001)29-34 suggests that any film that could be grown on the STO/Si platform could be grown on an ALD-grown STO buffer film on Ge, such as LaAlO3 and LaCoO3.32,38 The multitude of properties available to oxide heterostructures and remarkable similarity between perovskite oxides suggest this procedure could be utilized to study previously difficult or impossible growth combinations with such an industrially viable technique.
Figure 1 depicts the schematic of the vacuum system, which encompasses ALD, MBE, and analytical chambers connected by a 12-foot transfer line. The samples can be transferred in vacuo between each chamber. The baseline pressure of the transfer line is kept at approximately 1.0&#215;10-9 Torr by three ion pumps. The commercial angle-resolved ultraviolet and X-ray photoelectron spectroscopy (XPS) system is maintained with an ion pump such that the pressure in the analytical chamber is kept at approximately 1.0&#215;10-9 Torr.
The ALD reactor is a rectangular custom-built stainless steel chamber with a volume of 460 cm3 and length of 20 cm. A schematic of the ALD reactor is shown in Figure 2. The reactor is a hot wall, continuous cross-flow type reactor. Samples placed in the reactor have a clearance of 1.7 cm between the top surface of the substrate and the chamber ceiling and 1.9 cm between the bottom of the substrate and the chamber floor. A heating tape, powered by a dedicated power supply, is wrapped around the chamber from the inlet to approximately 2 cm beyond the exhaust port and provides temperature control of the reactor walls. A temperature controller adjusts the power input to the heating tape according to a temperature measurement taken by a thermal couple located between the heating tape and exterior reactor wall. The reactor is then completely wrapped with three additional heating tapes of constant power provided by a variac, and a final layer of fiberglass wool with aluminum foil covering provides insulation to promote uniform heating. The power output of the variac is adjusted such that the idling temperature (when the dedicated power supply is turned off) of the reactor is approximately 175 &#176;C. The reactor is passively cooled via ambient air. The substrate temperature is calculated using the linear-fit equation (1), where Ts (&#176;C) is the temperature of substrate and Tc (&#176;C) is the temperature of the reactor wall, obtained by directly measuring a substrate fitted with a thermocouple. A temperature profile exists along the flow direction of the chamber due to the cold gate valve that connects the reactor to the transfer line; the temperature profile perpendicular to the flow direction is negligible. The temperature profile causes a richer Sr deposition at the leading edge of the sample, but the composition variation along sample is small (less than a 5% difference between the leading and trailing edges of the sample) according to XPS.31 The exhaust of the reactor is connected to a turbomolecular pump and a mechanical pump. During the ALD process, the reactor is pumped by the mechanical pump to maintain the pressure at around 1 Torr. Otherwise, the reactor pressure is maintained below 2.0&#215;10-6 Torr by the turbomolecular pump.
(1) Ts=0.977Tc + 3.4
The MBE chamber is maintained at a baseline pressure of approximately 2.0&#215;10-9 Torr or below by a cryogenic pump. The partial pressure of various species in the MBE chamber is monitored by a residual gas analyzer. The background pressure of H2 is around 1.0&#215;10-9 Torr, while those of O2, CO, N2, CO2, and H2O, are less than 1.0&#215;10-10 Torr. In addition, the MBE chamber is also equipped with six effusion cells, a four-pocket electron beam evaporator, an atomic nitrogen plasma source and an atomic oxygen plasma source with high-precision piezoelectric leak valve, and a reflection high energy electron diffraction (RHEED) system for real-time in situ growth and crystallization observations. The sample manipulator allows the substrate be heated up to 1000 &#176;C using an oxygen-resistant silicon carbide heater.

<table border="0" cellpadding="0" cellspacing="0" width="963">
	<tbody>
		<tr height="20">
			<td height="20" style="height:20px;width:285px;">MBE</td>
			<td style="width:235px;">DCA</td>
			<td style="width:143px;">M600</td>
			<td style="width:301px;"></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Cryopump for MBE</td>
			<td>Brooks Automation, Inc.</td>
			<td>On-Board 8</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Residual Gas Analyzer for MBE</td>
			<td>Extorr, Inc.</td>
			<td>XT200M</td>
			<td></td>
		</tr>
		<tr height="23">
			<td height="23" style="height:23px;">ALD Reaction Chamber</td>
			<td>Huntington Mechanical Laboratories</td>
			<td>N/A</td>
			<td>Custom manufactured, hot-wall, stainless steel, rectangular (~20 cm long, 460 cm3)</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">ALD Saturator</td>
			<td>Swagelok/Larson Electronic Glass</td>
			<td>See comments</td>
			<td>Custom-built from parts supplied by Swagelok and Larson Electronic Glass. The saturator is made out of 316 stainless steel and Pyrex. All parts are connected via butt welding. Swagelok catalog numbers:SS-4-VCR-7-8VCRF, SS-4-VCR-1, SS-8-VCR-1-03816, SS-8-VCR-3-8MTW, 316L-12TB7-6-8, SS-8-VCR-9, SS-4-VCR-3-4MTW, SS-T2-S-028-20&#160; Larson Electronic Glass catalog number: SP-075-T</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Manual Valves for Saturators</td>
			<td>Swagelok</td>
			<td>SS-DLVCR4-P and 6LVV-DPFR4-P.</td>
			<td>Both diaphragm-sealed valves are used interchangably by this group. The specific connectors (VCR male/female/etc.) to use will depend on the actual system design.</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">ALD Valves</td>
			<td>Swagelok</td>
			<td>6LVV-ALD3TC333P-CV</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">ALD System Tubing</td>
			<td>Swagelok</td>
			<td></td>
			<td>316L tubing of various sizes. This group uses inner diameter of 1/4&#34;</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">ALD power supply</td>
			<td>AMETEK Programmable Power, Inc.</td>
			<td>Sorensen DCS80-13E</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">ALD Temperature Controller</td>
			<td>Schneider Electric</td>
			<td>Eurotherm 818P4</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">ALD Valve Controller&#160;</td>
			<td>National Instruments</td>
			<td>LabView</td>
			<td>Program developed within the group</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">XPS</td>
			<td>VG Scienta</td>
			<td></td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">RHEED</td>
			<td>Staib Instruments</td>
			<td>CB801420</td>
			<td>18 keV at ~3&#176; incident angle</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">RHEED Analysis System</td>
			<td>k-Space Associates</td>
			<td>kSA 400</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Digital UV Ozone System</td>
			<td>Novascan</td>
			<td>PSD-UV 6</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Ozone Elimination System</td>
			<td>Novascan</td>
			<td>PSD-UV OES-1000D</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Strontium bis(triisopropylcyclopentadienyl)</td>
			<td>Air Liquide</td>
			<td>HyperSr</td>
			<td>Mildly reactive to air and water. Further information supplied by Air Liquide can be found at https://www.airliquide.de/inc/dokument.php/standard/1148/airliquide-hypersr-datasheet.pdf</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Titanium tetraisopropoxide (TTIP)</td>
			<td>Sigma-Aldrich</td>
			<td>87560</td>
			<td>Flammable in liquid and vapor phase</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Ge (001) wafer</td>
			<td>MTI Corporation</td>
			<td>GESBA100D05C1</td>
			<td>4&#34;, single-side polished Sb-doped wafer with &#961; &#8776; 0.04 &#937;-cm</td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Argon (UHP)</td>
			<td>Praxair</td>
			<td>N/A</td>
			<td></td>
		</tr>
		<tr height="20">
			<td height="20" style="height:20px;">Deionized Water</td>
			<td>N/A</td>
			<td>N/A</td>
			<td>18.2 M&#937;-cm</td>
		</tr>
	</tbody>
</table>

epitaxial growth of perovskite strontium titanate on germanium via atomic layer deposition

Atomic layer deposition (ALD) is a commercially utilized deposition method for electronic materials. ALD growth of thin films offers thickness control and conformality by taking advantage of self-limiting reactions between vapor-phase precursors and the growing film. Perovskite oxides present potential for next-generation electronic materials, but to-date have mostly been deposited by physical methods. This work outlines a method for depositing SrTiO3 (STO) on germanium using ALD. Germanium has higher carrier mobilities than silicon and therefore offers an alternative semiconductor material with faster device operation. This method takes advantage of the instability of germanium's native oxide by using thermal deoxidation to clean and reconstruct the Ge (001) surface to the 2&#215;1 structure. 2-nm thick, amorphous STO is then deposited by ALD. The STO film is annealed under ultra-high vacuum and crystallizes on the reconstructed Ge surface. Reflection high-energy electron diffraction (RHEED) is used during this annealing step to monitor the STO crystallization. The thin, crystalline layer of STO acts as a template for subsequent growth of STO that is crystalline as-grown, as confirmed by RHEED. In situ X-ray photoelectron spectroscopy is used to verify film stoichiometry before and after the annealing step, as well as after subsequent STO growth. This procedure provides framework for additional perovskite oxides to be deposited on semiconductors via chemical methods in addition to the integration of more sophisticated heterostructures already achievable by physical methods.

Figures 5 and 6 show typical X-ray photoelectron spectra and RHEED images from a cleaned and deoxidized Ge substrate. A successfully-deoxidized Ge substrate is characterized by its &#34;smiley face&#34; 2&#215;1 reconstructed RHEED pattern.26,39 In addition, Kikuchi lines are also observed in the RHEED images, which indicate the cleanliness and long range order of the sample.40 The sharpness and intensity of the diffraction pattern also demonstrate the cleanliness of the surface. The Ge 3d X-ray photoelectron spectrum should be free of oxidized Ge peaks, with the Ge0 peak observed at 30 eV. This can also be confirmed by the absence of an O 1s feature at 531 eV.
The ALD-grown STO film is amorphous upon deposition and exemplified via a hazy RHEED image, such as that of Figure 6B. In order to achieve a crystalline film upon annealing, the ALD parameters are adjusted such that a slightly Sr-rich stoichiometry is obtained in the deposited STO film. This group typically aims for a ratio between Sr to total Sr and Ti (i.e., Sr/(Sr+Ti)) of 0.53 - 0.54. The film composition can be verified via integration of the X-ray photoelectron spectra with appropriate relative sensitivity factors and other parameters as shown in Section 8 of the Protocol. This group obtained the parameters by both consulting the Handbook of X-ray Photoelectron Spectroscopy by Moulder et al.,41 as well as using commercially available perovskite crystals as standards. A poor stoichiometric ratio between Sr and Ti (i.e., when the film is Ti-rich or Sr/(Sr+Ti) is greater than 0.57) will result in poor crystallinity, or even the lack thereof, after the annealing step.
Once the STO film has been annealed, its crystallinity can be observed via the RHEED pattern, as shown in Figures 6C and 6D. The RHEED pattern of an STO film with good epitaxial growth on Ge should exhibit sharp streak patterns. The crystallinity of the deposited STO film can also be confirmed by X-ray diffraction. Figure 7 depicts the X-ray diffraction pattern of epitaxial STO on Ge with characteristic peaks of STO (001) at 22.8&#176;, STO (002) at 46.5&#176;, and Ge (004) at 66.0&#176;. The epitaxial nature of the film can be directly confirmed by cross-sectional high-resolution transmission electron microscopy (HRTEM). Figure 8 shows the high quality epitaxial registry between STO and Ge as well as the abrupt transition between layers.
Electrical measurements of epitaxial STO on Ge can also be conducted. Figure 9 shows the capacitance-voltage (CV) and current-voltage (IV) measurements of a metal-insulator-semiconductor (MOS) capacitor created by depositing a 50-&#181;m radius Ti/Au top electrode on STO/n+Ge (001). The CV measurement of a 15-nm STO film from Figure 9A suggests the capacitance of the structure is 5.3 &#181;F/cm2. The dielectric constant of the STO film is therefore approximately 90 and yields an equivalent oxide thickness less than 0.7 nm. Figure 9B shows the leakage current density of the MOS capacitor is approximately 10 A/cm2 at an applied field of 0.7MV/cm. The high leakage current density should be expected due to the lack of conduction band offset between STO and Ge. Depositing other films on Ge, such as Al-doped STO and strontium hafnate (SHO), improves the leakage current density.26,35 In fact, SHO gives a leakage current density of less than 10-5 A/cm2 at the same applied field.
<img alt="Figure 1" src="/files/ftp_upload/54268/54268fig1.jpg" /> 
Figure 1. Schematic of the connected vacuum system. The vacuum system contains MBE, ALD, and analytical chambers connected together by an ultra-high vacuum transfer line, allowing in vacuo sample transfer. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" src="/files/ftp_upload/54268/54268fig2.jpg" /> 
Figure 2. ALD reactor design. The ALD chamber has a volume of 460 cm3 and length of 20 cm. The carrier gas delivers precursors from the saturators to the reactor, and exhaust gases are removed through the turbomolecular pump port. The sample is transferred to the reaction zone from the reactor end opposite to the gas inlet. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" src="/files/ftp_upload/54268/54268fig3.jpg" /> 
Figure 3. ALD precursor saturator. (A) Schematic of this group&#39;s custom built saturator as well as other parts used for precursor delivery into the ALD chamber. (B) and (C) show the top and bottom part of the saturator, respectively. The two parts are connected via a VCR fitting, and are disassembled when filling the saturator. All parts are made of 316 stainless steel, with the exception of a Pyrex-to-stainless steel adaptor, and are connected together via butt welding. Detailed information of these parts can be found in the List of Specific Reagents and Equipment. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" src="/files/ftp_upload/54268/54268fig4.jpg" /> 
Figure 4. Vacuum system sample holder. (A) A sample holder and an 18&#215;20 mm2 Ge substrate. (B) A sample holder with the Ge substrate loaded. Note that the polished side is facing down. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig4large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" src="/files/ftp_upload/54268/54268fig5.jpg" /> 
Figure 5. X-ray photoelectron spectra. (A) Ge 3d, (B) O 1s, (C) Sr 3d, and (D) Ti 2p before ALD growth (solid red line), after 36 unit cycles (~2 nm STO) (dashed brown line), and after 155 unit cycles (~8 nm STO) (solid black line). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig5large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 6" src="/files/ftp_upload/54268/54268fig6.jpg" /> 
Figure 6. RHEED images. (A) A clean Ge substrate after thermal deoxidation, (B) after the second STO deposition (155 unit cycles, as-deposited), and (C)-(D) after annealing at 650 &#176;C. The beam is aligned along the [110] and [100] azimuth for (C) and (D), respectively. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig6large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 7" src="/files/ftp_upload/54268/54268fig7.jpg" /> 
Figure 7. X-ray diffraction pattern. The diffraction pattern for a 15-nm thick STO film grown by ALD on Ge (001) at 225 &#176;C. Inset: rocking curve around the STO (002) peak. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig7large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 8" src="/files/ftp_upload/54268/54268fig8.jpg" /> 
Figure 8. Cross-sectional high-resolution transmission electron micrograph. HRTEM depicts high quality STO on Ge. Inset: selected-area electron diffraction pattern showing epitaxial registry between the substrate and film. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig8large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 9" src="/files/ftp_upload/54268/54268fig9.jpg" /> 
Figure 9. C-V and I-V curve of a MOS capacitor with STO. (A) Specific capacitance as a function of voltage bias for a 15-nm thick STO film on n+ Ge (001) by ALD, and (B) the gate leakage current density as a function of voltage bias measured from a typical Au(Ti)/STO/Ge structure. The metal-insulator-semiconductor capacitor structure was created by depositing 50-&#181;m radius Ti/Au top electrode on the STO film. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/54268/54268fig9large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<table fo:keep-together.within-page="1">
	<tbody>
		<tr>
			<td rowspan="2">Region Name</td>
			<td rowspan="2">Lens Mode</td>
			<td rowspan="2">Pass Energy (eV)</td>
			<td rowspan="2">Excitation Energy (eV)</td>
			<td rowspan="2">Energy Mode</td>
			<td colspan="2">Energy (eV)</td>
			<td rowspan="2">Energy Step (meV)</td>
			<td rowspan="2">Step Time (sec)</td>
			<td rowspan="2">Steps</td>
		</tr>
		<tr>
			<td>Low</td>
			<td>High</td>
		</tr>
		<tr>
			<td>Survey Scan</td>
			<td>Transmission</td>
			<td>200</td>
			<td>1486.6</td>
			<td>Binding</td>
			<td>0</td>
			<td>1300</td>
			<td>800</td>
			<td>0.286</td>
			<td>1657</td>
		</tr>
		<tr>
			<td>Sr 3d</td>
			<td>Transmission</td>
			<td>100</td>
			<td>1486.6</td>
			<td>Binding</td>
			<td>127.805</td>
			<td>140.1942</td>
			<td>50</td>
			<td>0.157</td>
			<td>499</td>
		</tr>
		<tr>
			<td>Ti 2p</td>
			<td>Transmission</td>
			<td>100</td>
			<td>1486.6</td>
			<td>Binding</td>
			<td>449</td>
			<td>471</td>
			<td>50</td>
			<td>0.157</td>
			<td>691</td>
		</tr>
		<tr>
			<td>O 1s</td>
			<td>Transmission</td>
			<td>100</td>
			<td>1486.6</td>
			<td>Binding</td>
			<td>515</td>
			<td>545</td>
			<td>50</td>
			<td>0.157</td>
			<td>851</td>
		</tr>
		<tr>
			<td>C 1s</td>
			<td>Transmission</td>
			<td>100</td>
			<td>1486.6</td>
			<td>Binding</td>
			<td>277.5</td>
			<td>302.5</td>
			<td>50</td>
			<td>0.157</td>
			<td>751</td>
		</tr>
		<tr>
			<td>Ge 3d</td>
			<td>Transmission</td>
			<td>100</td>
			<td>1486.6</td>
			<td>Binding</td>
			<td>24</td>
			<td>36</td>
			<td>50</td>
			<td>0.157</td>
			<td>491</td>
		</tr>
	</tbody>
</table>
Table 1. XPS Scan Settings.

Watch this Scientific Journal Video about Epitaxial Growth of Perovskite Strontium Titanate on Germanium via Atomic Layer Deposition at JoVE.com

Epitaxial Growth of Perovskite Strontium Titanate on Germanium via Atomic Layer Deposition

This work details the procedures for the growth and characterization of crystalline SrTiO3 directly on germanium substrates by atomic layer deposition. The procedure illustrates the ability of an all-chemical growth method to integrate oxides monolithically onto semiconductors for metal-oxide semiconductor devices.

Atomic layer deposition (ALD) is a commercially utilized deposition method for electronic materials. ALD growth of thin films offers thickness control and ...

epitaxial-growth-perovskite-strontium-titanate-on-germanium-via

Nanyang Technological University

Research

JoVE Journal

Chemistry

12.3K Views.  The University of Texas at Austin. This work details the procedures for the growth and characterization of crystalline SrTiO3 directly on germanium substrates by atomic layer deposition. The procedure illustrates the ability of an all-chemical growth method to integrate oxides monolithically onto semiconductors for metal-oxide semiconductor devices.

Video: Epitaxial Growth of Perovskite Strontium Titanate on Germanium via Atomic Layer Deposition

Preparation of Hydrophobic Metal-Organic Frameworks via Plasma Enhanced Chemical Vapor Deposition of Perfluoroalkanes for the Removal of Ammonia

Plasma enhanced chemical vapor deposition (PECVD) of perfluoroalkanes has long been studied for tuning the wetting properties of surfaces. For high surface area microporous materials, such as metal-organic frameworks (MOFs), unique challenges present themselves for PECVD treatments. Herein the protocol for development of a MOF that was previously unstable to humid conditions is presented. The protocol describes the synthesis of Cu-BTC (also known as HKUST-1), the treatment of Cu-BTC with PECVD of perfluoroalkanes, the aging of materials under humid conditions, and the subsequent ammonia microbreakthrough experiments on milligram quantities of microporous materials. Cu-BTC has an extremely high surface area (~1,800 m2/g) when compared to most materials or surfaces that have been previously treated by PECVD methods. Parameters such as chamber pressure and treatment time are extremely important to ensure the perfluoroalkane plasma penetrates to and reacts with the inner MOF surfaces. Furthermore, the protocol for ammonia microbreakthrough experiments set forth here can be utilized for a variety of test gases and microporous materials.

Herein the procedures for plasma enhanced chemical vapor deposition of perfluoroalkanes on microporous materials such as metal-organic frameworks to enhance their stability and hydrophobicity are described. Furthermore, breakthrough testing of milligram quantities of samples is described in detail.

Plasma enhanced chemical vapor deposition (PECVD) of perfluoroalkanes has long been studied for tuning the wetting properties of surfaces. For high ...

Atomically Defined Templates for Epitaxial Growth of Complex Oxide Thin Films

Atomically defined substrate surfaces are prerequisite for the epitaxial growth of complex oxide thin films. In this protocol, two approaches to obtain such surfaces are described. The first approach is the preparation of single terminated perovskite SrTiO3 (001) and DyScO3 (110) substrates. Wet etching was used to selectively remove one of the two possible surface terminations, while an annealing step was used to increase the smoothness of the surface. The resulting single terminated surfaces allow for the heteroepitaxial growth of perovskite oxide thin films with high crystalline quality and well-defined interfaces between substrate and film. In the second approach, seed layers for epitaxial film growth on arbitrary substrates were created by Langmuir-Blodgett (LB) deposition of nanosheets. As model system Ca2Nb3O10- nanosheets were used, prepared by delamination of their layered parent compound HCa2Nb3O10. A key advantage of creating seed layers with nanosheets is that relatively expensive and size-limited single crystalline substrates can be replaced by virtually any substrate material.

Various procedures are outlined to prepare atomically defined templates for epitaxial growth of complex oxide thin films. Chemical treatments of single crystalline SrTiO3 (001) and DyScO3 (110) substrates were performed to obtain atomically smooth, single terminated surfaces. Ca2 Nb3 O10- nanosheets were used to create atomically defined templates on arbitrary substrates.

Atomically defined substrate surfaces are prerequisite for the epitaxial growth of complex oxide thin films. In this protocol, two approaches to obtain ...

Synthesis and Reaction Chemistry of Nanosize Monosodium Titanate

This paper describes the synthesis and peroxide-modification of nanosize monosodium titanate (nMST), along with an ion-exchange reaction to load the material with Au(III) ions. The synthesis method was derived from a sol-gel process used to produce micron-sized monosodium titanate (MST), with several key modifications, including altering reagent concentrations, omitting a particle seed step, and introducing a non-ionic surfactant to facilitate control of particle formation and growth. The resultant nMST material exhibits spherical-shaped particle morphology with a monodisperse distribution of particle diameters in the range from 100 to 150&#160;nm. The nMST material was found to have a Brunauer-Emmett-Teller (BET) surface area of 285 m2g-1, which is more than an order of magnitude higher than the micron-sized MST. The isoelectric point of the nMST measured 3.34 pH units, which is a pH unit lower than that measured for the micron-size MST. The nMST material was found to serve as an effective ion exchanger under weakly acidic conditions for the preparation of an Au(III)-exchange nanotitanate. In addition, the formation of the corresponding peroxotitanate was demonstrated by reaction of the nMST with hydrogen peroxide.

The surfactant mediated sol-gel synthesis of nanosized monosodium titanate is described, along with preparation of the corresponding peroxide modified material. An ion-exchange reaction with Au(III) is also presented.

This paper describes the synthesis and peroxide-modification of nanosize monosodium titanate (nMST), along with an ion-exchange reaction to load the ...

Layer-by-layer Synthesis and Transfer of Freestanding Conjugated Microporous Polymer Nanomembranes

CMP as large surface area materials have attracted growing interest recently, due to their high variability in the incorporation of functional groups in combination with their outstanding thermal and chemical stability, and low densities. However, their insoluble nature causes problems in their processing since usually applied techniques such as spin coating are not available. Especially for membrane applications, where the processing of CMP as thin films is desirable, the processing problems have hindered their commercial application.
Here we describe the interfacial synthesis of CMP thin films on functionalized substrates via molecular layer-by-layer (l-b-l) synthesis. This process allows the preparation of films with desired thickness and composition and even desired composition gradients.
The use of sacrificial supports allows the preparation of freestanding membranes by dissolution of the support after the synthesis. To handle such ultra-thin freestanding membranes the protection with sacrificial coatings showed great promise, to avoid rupture of the nanomembranes. To transfer the nanomembranes to the desired substrate, the coated membranes are upfloated at the air-liquid interface and then transferred via dip coating.

In this paper we describe the interfacial synthesis of conjugated microporous polymers (CMP) on sacrificial substrates, and the dissolution of the substrate for the preparation of freestanding CMP nanomembranes. In addition, we will describe how the fragile nanomembranes can be transferred to other substrates.

CMP as large surface area materials have attracted growing interest recently, due to their high variability in the incorporation of functional groups in ...

Preparation of Macroporous Epitaxial Quartz Films on Silicon by Chemical Solution Deposition

This work describes the detailed protocol for preparing piezoelectric macroporous epitaxial quartz films on silicon(100) substrates. This is a three-step process based on the preparation of a sol in a one-pot synthesis which is followed by the deposition of a gel film on Si(100) substrates by evaporation induced self-assembly using the dip-coating technique and ends with a thermal treatment of the material to induce the gel crystallization and the growth of the quartz film. The formation of a silica gel is based on the reaction of a tetraethyl orthosilicate and water, catalyzed by HCl, in ethanol. However, the solution contains two additional components that are essential for preparing mesoporous epitaxial quartz films from these silica gels dip-coated on Si. Alkaline earth ions, like Sr2+ act as glass melting agents that facilitate the crystallization of silica and in combination with cetyl trimethylammonium bromide (CTAB) amphiphilic template form a phase separation responsible of the macroporosity of the films. The good matching between the quartz and silicon cell parameters is also essential in the stabilization of quartz over other SiO2 polymorphs and is at the origin of the epitaxial growth.

A protocol is presented for the preparation of piezoelectric macroporous epitaxial films of quartz on silicon by solution chemistry using dip-coating and thermal treatments in air.

This work describes the detailed protocol for preparing piezoelectric macroporous epitaxial quartz films on silicon(100) substrates. This is a three-step ...

Photochemical Oxidative Growth of Iridium Oxide Nanoparticles on CdSe@CdS Nanorods

We demonstrate a procedure for the photochemical oxidative growth of iridium oxide catalysts on the surface of seeded cadmium selenide-cadmium sulfide (CdSe@CdS) nanorod photocatalysts. Seeded rods are grown using a colloidal hot-injection method and then moved to an aqueous medium by ligand exchange. CdSe@CdS nanorods, an iridium precursor and other salts are mixed and illuminated. The deposition process is initiated by absorption of photons by the semiconductor particle, which results with formation of charge carriers that are used to promote redox reactions. To insure photochemical oxidative growth we used an electron scavenger. The photogenerated holes oxidize the iridium precursor, apparently in a mediated oxidative pathway. This results in the growth of high quality crystalline iridium oxide particles, ranging from 0.5 nm to about 3 nm, along the surface of the rod. Iridium oxide grown on CdSe@CdS heterostructures was studied by a variety of characterization methods, in order to evaluate its characteristics and quality. We explored means for control over particle size, crystallinity, deposition location on the CdS rod, and composition. Illumination time and excitation wavelength were found to be key parameters for such control. The influence of different growth conditions and the characterization of these heterostructures are described alongside a detailed description of their synthesis. Of significance is the fact that the addition of iridium oxide afforded the rods astounding photochemical stability under prolonged illumination in pure water (alleviating the requirement for hole scavengers).

A protocol for the photochemical oxidative growth of small crystalline iridium oxide nanoparticles on the surface of CdSe@CdS seeded rod nanoparticles is presented.

We demonstrate a procedure for the photochemical oxidative growth of iridium oxide catalysts on the surface of seeded cadmium selenide-cadmium sulfide ...

Influence of Hybrid Perovskite Fabrication Methods on Film Formation, Electronic Structure, and Solar Cell Performance

Hybrid organic/inorganic halide perovskites have lately been a topic of great interest in the field of solar cell applications, with the potential to achieve device efficiencies exceeding other thin film device technologies. Yet, large variations in device efficiency and basic physical properties are reported. This is due to unintentional variations during film processing, which have not been sufficiently investigated so far. We therefore conducted an extensive study of the morphology and electronic structure of a large number of CH3NH3PbI3 perovskite where we show how the preparation method as well as the mixing ratio of educts methylammonium iodide and lead(II) iodide impact properties like film formation, crystal structure, density of states, energy levels, and ultimately the solar cell performance.

We present an extensive study on the effects of different fabrication methods for organic/inorganic perovskite thin films by comparing crystal structures, density of states, energy levels, and ultimately the solar cell performance.

Hybrid organic/inorganic halide perovskites have lately been a topic of great interest in the field of solar cell applications, with the potential to ...

Reactive Vapor Deposition of Conjugated Polymer Films on Arbitrary Substrates

We demonstrate a method of conformally coating conjugated polymers on arbitrary substrates using a custom-designed, low-pressure reaction chamber. Conductive polymers, poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(3,4-propylenedioxythiophene) (PProDOT), and a semiconducting polymer, poly(thieno[3,2-b]thiophene) (PTT), were deposited on unconventional highly-disordered and textured substrates with high surface areas, such as paper, towels and fabrics. This reported deposition chamber is an improvement of previous vapor reactors because our system can accommodate both volatile and nonvolatile monomers, such as 3,4-propylenedioxythiophene and thieno[3,2-b]thiophene. Utilization of both solid and liquid oxidants are also demonstrated. One limitation of this method is that it lacks sophisticated in situ thickness monitors. Polymer coatings made by the commonly used solution-based coating methods, such as spin-coating and surface grafting, are often not uniform or susceptible to mechanical degradation. This reported vapor phase deposition method overcomes those drawbacks and is a strong alternative to common solution-based coating methods. Notably, polymer films coated by the reported method are uniform and conformal on rough surfaces, even at a micrometer scale. This feature allows for future application of vapor deposited polymers in electronics devices on flexible and highly textured substrates.

This paper presents a protocol for reactive vapor deposition of poly(3,4-ethylenedioxythiophene), poly(3,4-propylenedioxythiophene), and poly(thieno[3,2-b]thiophene) films on glass slides and rough substrates, such as textiles and paper.

We demonstrate a method of conformally coating conjugated polymers on arbitrary substrates using a custom-designed, low-pressure reaction chamber. ...

Deposition of Porous Sorbents on Fabric Supports

A microwave deposition technique for silanes, previously described for production of oleophobic fabrics, is adapted to provide a fabric support material that can be subsequently treated by dip coating. Dip coating with a sol preparation provides a supported porous layer on the fabric. In this case, the porous layer is a porphyrin functionalized sorbent system based on a powdered material that has been demonstrated previously for the capture and conversion of phosgene. A representative coating is applied to cotton fabric at a loading level of 10 mg/g. This coating has minimal impact on water vapor transport through the fabric (93% of the support fabric rate) while significantly reducing transport of 2-chloroethyl ethyl sulfide (CEES) through the material (7% of support fabric rate). The described approaches are suitable for use with other fabrics providing amine and hydroxyl groups for modification and can be used in combination with other sol preparations to produce varying functionality.

This report details a microwave-initiated approach for deposition of porphyrin functionalized porous organosilicate sorbents on a cotton fabric and demonstrates reduction in 2-chloroethyl ethyl sulfide (CEES) transport through the fabric resulting from this treatment.

A microwave deposition technique for silanes, previously described for production of oleophobic fabrics, is adapted to provide a fabric support material ...

Solvothermal Synthesis of MIL-96 and UiO-66-NH2 on Atomic Layer Deposited Metal Oxide Coatings on Fiber Mats

Metal-organic frameworks (MOFs), which contain reactive metal clusters and organic ligands allowing for large porosities and surface areas, have proven effective in gas adsorption, separations, and catalysis. MOFs are most commonly synthesized as bulk powder, requiring additional processes to adhere them to functional devices and fabrics that risk decreasing the powder porosity and adsorption capacity. Here, we demonstrate a method of first coating fabrics with metal oxide films using atomic layer deposition (ALD). This process creates conformal films of controllable thickness on each fiber, while providing a more reactive surface for MOF nucleation. By submerging the ALD coated fabric in solution during solvothermal MOF synthesis, the MOFs create a conformal, well-adhered coating on the fibers, resulting in a MOF-functionalized fabric, without additional adhesion materials that may block MOF pores and functional sites. Here we demonstrate two solvothermal synthesis methods. First, we form a MIL-96(Al) layer on polypropylene fibers using synthetic conditions that convert the metal oxide to MOF. Using initial inorganic films of varying thicknesses, diffusion of the organic linker into the inorganic allows us to control the extent of MOF loading on the fabric. Second, we perform a solvothermal synthesis of UiO-66-NH2 in which the MOF nucleates on the conformal metal oxide coating on polyamide-6 (PA-6) fibers, thereby producing a uniform and conformal thin film of MOF on the fabric. The resulting materials can be directly incorporated into filter devices or protective clothing and eliminate the maladroit qualities of loose powder.

Solvothermal Synthesis of MIL-96 and UiO-66-NH2 on Atomic Layer Deposited Metal Oxide Coatings on Fiber Mats

Metal-organic frameworks are effective in gas storage and heterogeneous catalysis, but typical synthesis methods result in loose powders that are difficult to incorporate into smart materials. We demonstrate a method of first coating fabrics with ALD metal oxides, resulting in conformal films of MOF on the fabrics during solvothermal synthesis.

Metal-organic frameworks (MOFs), which contain reactive metal clusters and organic ligands allowing for large porosities and surface areas, have proven ...