This study has been partly funded by the Dutch Journal of Dentistry (Stichting Bevordering Tandheelkundige Kennis, NTVT BV).

Institutional ethical approval for the protocol was obtained (ABR code: NL31401.091.10).
NOTE: The following steps describe the 3DWA protocol.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/63680/63680fig01.jpg" /> 
Figure 1: Visual representation of the steps for superimposition and quantitative wear measurement. This figure has been modified from K. Ning et al.23. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/63680fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
1. Acquisition
NOTE: The following procedure was used to scan dentitions.
<ol>
	<li>Isolate the dentition using lip retractors, dry pads, and curly saliva ejectors.</li>
	<li>Lightly powder the dentition before scanning if required for the intra-oral scanner used.</li>
	<li>Scan the dentition according to the manufacturer&#39;s instructions. Refer to the Table of Materials for the products used.</li>
</ol>
2. Superimposition
NOTE: The following procedure was used for superimposition and quantitative wear measurement.
<ol>
	<li>Open the 3D software program (see Table of Materials). Open (or import) the old and new scans (STL-/PLY-file) of the upper and lower jaws.</li>
	<li>Select the separated teeth.
	<ol>
		<li>Select a scan, and then use Lasso Selection and Select Through to select a tooth. Save the separated tooth using Tools &#62; New Object &#62; From Selection. Select Copy and Paste and give the object a name (e.g., 17_2016_Original).</li>
		<li>Repeat this procedure for each tooth of the upper and lower jaws, as well as for the old and new scans. Before selecting a new tooth, first deselect the previously selected tooth (click on the right mouse button, and then on Clear All).</li>
		<li>Select a specific tooth in Model Manager (e.g., 17_2016). Change Select Through with Select Visible. Use the Lasso tool to select soft tissue and contact areas and delete (right-click &#62; Delete, or press Delete button on the keyboard) these parts. Repeat this for all individual teeth.</li>
	</ol>
	</li>
	<li>Calculate best fit per tooth.
	<ol>
		<li>Select in Model Manager the old scan and (by right-clicking the mouse) set this as Set Reference. Similarly, set the new scan as Set Test. Select the Reference scan and, in the Alignment tab, choose Best Fit Alignment, set Deviator Elimination to 1, press Apply, and then OK.</li>
		<li>Check the quality of the best fit. Go to Analysis &#62; Selection Through Object and create an intersection perpendicular to the surface from the buccal to the palatal side. Press on Compute. A cross-section of both scans (red and black lines) will become visible. Check if the Best Fit is correct and that the new scan is not superpositioned (higher) compared to the old scan.</li>
		<li>Press OK to go back to the scan. 
		NOTE: Optionally, the best fit might need to be improved when areas with too much wear interfere with obtaining a proper best fit. This step is described in 2.3.3.1.
		<ol>
			<li>Deselect areas on the old and new scans with severe material loss using the Lasso tool. Select areas on, if possible, at least three surfaces (buccal-palatinal/lingual-occlusal). Repeat step 2.3.1 through step 2.3.3.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Select Analysis &#62; 3D Compare to create a colorized model of the wear. In order to obtain wear facets as negative values in the results, perform the following steps.
	<ol>
		<li>Change spectrum as follows: Color Segment: 21; Max. Critical: 0.2 mm; Max. Nominal: 0.02 mm; Min. Nominal: -0.02 mm; Min. Critical: -0.2 mm; Decimal Places: 3.</li>
		<li>Click on Apply and then OK. The result of the 3D Compare is presented in the Model Manager. 
		&#8203;NOTE: Height decrease (wear) is shown in blue, and height increase is shown in yellow-red. Surfaces with no changes are shown in green. Surfaces the software was unable to compute due to severe loss are shown in grey. In that case, step 3.2 is followed instead of step 3.1.</li>
	</ol>
	</li>
</ol>
3. Quantitative wear measurement: Height
<ol>
	<li>Measure the vertical height loss.
	<ol>
		<li>Click on Set Result on the fitted and compared tooth. Go to Create Annotations in the Analysis tab. Change the Deviation Radius to 0.1 mm. Select the area with the largest amount of wear (darkest blue point) and click on OK to go back to the scans.</li>
		<li>Use Edit Spectrum to raise or decrease the value of Max Critical when the darkest blue area is too large to determine the point of highest wear. It changes the color, resulting in one clear point of darkest blue.</li>
		<li>Export the value from the Annotation on the point of highest wear to the data system.</li>
	</ol>
	</li>
	<li>Determine the vertical material loss on 2D images with 2D Dimensions (2D Compare method).
	<ol>
		<li>Set the old scan as the reference scan and the new scan as the test scan.</li>
		<li>Make multiple cross-sections (Analysis &#62; Section Through Object &#62; Compute &#62; OK) on the locations/cusps with the largest loss of material (use the 3D Compare result to determine the location).</li>
		<li>Click on Test scan, and then select 2D Dimensions under the Analysis tab. In View Control, select the cross-section showing the highest height difference in the to-be-measured area.</li>
		<li>Select Parallels for Dimension Type.</li>
		<li>In the Pick Methods, click on Test. Make a mark on the Test scan at the location of the largest wear, then click on REF in the Pick Methods and make a mark on the Reference scan. Click on one selected point (highest amount of wear) to obtain the result and export this to the data system, and then click on OK.</li>
	</ol>
	</li>
</ol>
4. Quantitative wear measurement: Volume
<ol>
	<li>Trim the teeth
	<ol>
		<li>Select the tooth to be compared. Right-click on the scan and then click on Duplicate to make copies of the old and new scans of the to-be-measured tooth. Remove the automations from the copy by selecting Automations, right-clicking it, and then clicking on Delete. Select both copies of the old and new scans of the tooth.</li>
		<li>Go to Polygons and select Trim with Plane. Trim interdental areas and then cervical areas by creating intersections, leaving only a closed occlusal surface. Trim by drawing the intersection, resulting in a red selected area and a blue unselected area divided by the intersection.</li>
		<li>Click on Intersect Plane, Delete Selection, and then Close Intersection and OK to cut off the selected area on the interdental and cervical surfaces and create a closed off volume. If necessary, first reverse the selected area if the software selects the occlusal side to be deleted. 
		NOTE: In case the error &#34;the intersection cannot be closed&#34; appears, there is a hole in the chosen intersection preventing it from being closed. Slightly adjust the chosen intersection to solve this.</li>
	</ol>
	</li>
	<li>Close the remaining (small) holes.
	<ol>
		<li>Close small holes in the scans by selecting Fill all. Selected holes are marked with a green border, and, after filling, those will become red.</li>
		<li>If there are too many or too large holes preventing measurement of volume, exclude the tooth.</li>
	</ol>
	</li>
	<li>Measure the volumes of both objects.
	<ol>
		<li>Go to Analysis &#62; Compute Volume. If the volume is 0, then this means that a hole is still present in the object.</li>
		<li>Export the values of the old and new volumes to the preferred data system.</li>
	</ol>
	</li>
</ol>
5. Statistical analysis
<ol>
	<li>Calculate the protocol precision with a one-sample T-test, determining the structural and random error for both the height (mm) and volume (mm3). 
	NOTE: The random error has a zero mean and is referred to as the duplicate measurement error (DME). As the DME is present twice in repeated measurements, the DME was calculated as the standard deviation of the differences divided by &#8730;2.</li>
	<li>Calculate the intra- and inter-precision with the paired T-test, from which the correlation, structural error, and DME are reported.</li>
	<li>To visualize the agreement, obtain Bland-Altman and violin plots.</li>
	<li>To compare and interpret results, use the trimmed ranges (P90 minus P10) calculated from the larger group of 55 patients regarding tooth wear after 0-1-, 0-3- and 0-5-year intervals for height (mm) and volume (mm3). 
	NOTE: These ranges were slightly trimmed to emphasize the range of more normal or less normal observations, whereas a full range would be determined by very specific observations.</li>
</ol>

<ol>
	<li>Mehta, S. B., Loomans, B. A. C., Banerji, S., Bronkhorst, E. M., Bartlett, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+investigation+into+the+impact+of+tooth+wear+on+the+oral+health+related+quality+of+life+amongst+adult+dental+patients+in+the+United+Kingdom,+Malta+and+Australia.">An investigation into the impact of tooth wear on the oral health related quality of life amongst adult dental patients in the United Kingdom, Malta and Australia.</a> Journal of Dentistry. 99, 103409 (2020).</li><li>Sterenborg, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+influence+of+management+of+tooth+wear+on+oral+health-related+quality+of+life.">The influence of management of tooth wear on oral health-related quality of life.</a> Clinical Oral Investigations. 22 (7), 2567-2573 (2018).</li><li>Wetselaar, P., Vermaire, J. H., Visscher, C. M., Lobbezoo, F., Schuller, A. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+prevalence+of+tooth+wear+in+the+Dutch+adult+population.">The prevalence of tooth wear in the Dutch adult population.</a> Nederlands Tijdschrift voor Tandheelkunde. 125 (4), 205-213 (2018).</li><li>Pintado, M. R., Anderson, G. C., DeLong, R., Douglas, W. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Variation+in+tooth+wear+in+young+adults+over+a+two-year+period.">Variation in tooth wear in young adults over a two-year period.</a> Journal of Prosthetic Dentistry. 77 (3), 313-320 (1997).</li><li>Lambrechts, P., Braem, M., Vuylsteke-Wauters, M., Vanherle, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+in+vivo+wear+of+human+enamel.">Quantitative in vivo wear of human enamel.</a> Journal of Dental Research. 68 (12), 1752-1754 (1989).</li><li>Rodriguez, J. M., Austin, R. S., Bartlett, D. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+vivo+measurements+of+tooth+wear+over+12+months.">In vivo measurements of tooth wear over 12 months.</a> Caries Research. 46 (1), 9-15 (2012).</li><li>Bartlett, D. W., Blunt, L., Smith, B. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measurement+of+tooth+wear+in+patients+with+palatal+erosion.">Measurement of tooth wear in patients with palatal erosion.</a> British Dental Journal. 182 (5), 179-184 (1997).</li><li>Al-Omiri, M. K., Sghaireen, M. G., Alzarea, B. K., Lynch, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantification+of+incisal+tooth+wear+in+upper+anterior+teeth:+conventional+vs+new+method+using+toolmakers+microscope+and+a+three-dimensional+measuring+technique.">Quantification of incisal tooth wear in upper anterior teeth: conventional vs new method using toolmakers microscope and a three-dimensional measuring technique.</a> Journal of Dentistry. 41 (12), 1214-1221 (2013).</li><li>Ahmed, K. E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Clinical+monitoring+of+tooth+wear+progression+in+patients+over+a+period+of+one+year+using+CAD/CAM.">Clinical monitoring of tooth wear progression in patients over a period of one year using CAD/CAM.</a> The International Journal of Prosthodontics. 30 (2), 153-155 (2017).</li><li>Mangano, F., Gandolfi, A., Luongo, G., Logozzo, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Intraoral+scanners+in+dentistry:+a+review+of+the+current+literature.">Intraoral scanners in dentistry: a review of the current literature.</a> BMC Oral Health. 17 (1), 149 (2017).</li><li>Meireles, A. B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Dental+wear+estimation+using+a+digital+intra-oral+optical+scanner+and+an+automated+3D+computer+vision+method.">Dental wear estimation using a digital intra-oral optical scanner and an automated 3D computer vision method.</a> Computer Methods in Biomechanics and Biomedical Engineering. 19 (5), 507-514 (2016).</li><li>DeLong, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Intra-oral+restorative+materials+wear:+rethinking+the+current+approaches:+how+to+measure+wear.">Intra-oral restorative materials wear: rethinking the current approaches: how to measure wear.</a> Dental Materials. 22 (8), 702-711 (2006).</li><li>O'Toole, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Quantitative+tooth+wear+analysis+of+index+teeth+compared+to+complete+dentition.">Quantitative tooth wear analysis of index teeth compared to complete dentition.</a> Journal of Dentistry. 97, 103342 (2020).</li><li>Kumar, S., Keeling, A., Osnes, C., Bartlett, D., O'Toole, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+sensitivity+of+digital+intraoral+scanners+at+measuring+early+erosive+wear.">The sensitivity of digital intraoral scanners at measuring early erosive wear.</a> Journal of Dentistry. 81, 39-42 (2019).</li><li>Gkantidis, N., Dritsas, K., Ren, Y., Halazonetis, D., Katsaros, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+accurate+and+efficient+method+for+occlusal+tooth+wear+assessment+using+3D+digital+dental+models.">An accurate and efficient method for occlusal tooth wear assessment using 3D digital dental models.</a> Scientific Reports. 10 (1), 10103 (2020).</li><li>Witecy, C., Ganss, C., W&#246;stmann, B., Schlenz, M. B., Schlenz, M. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Monitoring+of+erosive+tooth+wear+with+intraoral+scanners+in+vitro.">Monitoring of erosive tooth wear with intraoral scanners in vitro.</a> Caries Research. 55 (3), 215-224 (2021).</li><li>O'Toole, S., Osnes, C., Bartlett, D., Keeling, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigation+into+the+accuracy+and+measurement+methods+of+sequential+3D+dental+scan+alignment.">Investigation into the accuracy and measurement methods of sequential 3D dental scan alignment.</a> Dental Materials. 35 (3), 495-500 (2019).</li><li>Abduo, J., Elseyoufi, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Accuracy+of+intraoral+scanners:+A+systematic+review+of+influencing+factors.">Accuracy of intraoral scanners: A systematic review of influencing factors.</a> European Journal of Prosthodontics and Restorative Dentistry. 26 (3), 101-121 (2018).</li><li>Winkler, J., Gkantidis, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Trueness+and+precision+of+intraoral+scanners+in+the+maxillary+dental+arch:+an+in+vivo+analysis.">Trueness and precision of intraoral scanners in the maxillary dental arch: an in vivo analysis.</a> Scientific Reports. 10 (1), 1172 (2020).</li><li>Michou, S., Vannahme, C., Ekstrand, K. R., Benetti, A. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Detecting+early+erosive+tooth+wear+using+an+intraoral+scanner+system.">Detecting early erosive tooth wear using an intraoral scanner system.</a> Journal of Dentistry. 100, 103445 (2020).</li><li>O'Toole, S., Osnes, C., Bartlett, D., Keeling, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Investigation+into+the+validity+of+WearCompare,+a+purpose-built+software+to+quantify+erosive+tooth+wear+progression.">Investigation into the validity of WearCompare, a purpose-built software to quantify erosive tooth wear progression.</a> Dental Materials. 35 (10), 1408-1414 (2019).</li><li>O'Toole, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Influence+of+scanner+precision+and+analysis+software+in+quantifying+three-dimensional+intraoral+changes:+two-factor+factorial+experimental+design.">Influence of scanner precision and analysis software in quantifying three-dimensional intraoral changes: two-factor factorial experimental design.</a> Journal of Medical Internet Research. 22 (11), 17150 (2020).</li><li>Ning, K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Wear+behavior+of+a+microhybrid+composite+vs.+a+nanocomposite+in+the+treatment+of+severe+tooth+wear+patients:+A+5-year+clinical+study.">Wear behavior of a microhybrid composite vs. a nanocomposite in the treatment of severe tooth wear patients: A 5-year clinical study.</a> Dental Materials. 37 (12), 1819-1827 (2021).</li><li>Smith, B. G., Knight, J. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+index+for+measuring+the+wear+of+teeth.">An index for measuring the wear of teeth.</a> British Dental Journal. 156 (12), 435-438 (1984).</li><li>Wetselaar, P., Lobbezoo, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+tooth+wear+evaluation+system:+a+modular+clinical+guideline+for+the+diagnosis+and+management+planning+of+worn+dentitions.">The tooth wear evaluation system: a modular clinical guideline for the diagnosis and management planning of worn dentitions.</a> Journal of Oral Rehabilitation. 43 (1), 69-80 (2016).</li><li>Bartlett, D., Ganss, C., Lussi, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Basic+Erosive+Wear+Examination+(BEWE):+a+new+scoring+system+for+scientific+and+clinical+needs.">Basic Erosive Wear Examination (BEWE): a new scoring system for scientific and clinical needs.</a> Clinical Oral Investigations. 12, 65-68 (2008).</li></ol>

The authors have stated explicitly that there are no conflicts of interest in connection with this article.

Critical steps protocol: 
The 3DWA protocol has been shown to provide precise height measurements with excellent inter- and intra-agreement. For volume measurements, however, the protocol is not suitable. The major factors determining the precision of both acquisition and superimposition were the isolation during scanning and finding the best fit while superimposing. Superimposition is straightforward if the teeth have not changed but becomes increasingly difficult when wear progresses, especially if the wear is not easily located but involves large sections of the surface.
In a clinical situation, negative wear (growth) may simply be ignored, as was done in this study, as it is an impossible outcome. Scanning errors, such as saliva droplets, the thickness of powder coating, or flaring are problematic even in unchanged teeth and may not always be readily detectable, contributing to measurement error.
Modifications and troubleshooting of the method 
Performing the best fit procedure 
When performing a best fit procedure on teeth with wear, the algorithm behind the root mean square (RMS)-value will always make the average distance between the points in the mesh as close to zero as possible. In teeth with wear progression, this may result in a decrease in the distance in the areas with wear and an increase in the areas without or with less wear. This will result in an underestimation of the wear in surfaces with wear. Since this is a population with moderate to severe wear, performing a standard best fit alignment followed by deselecting occlusal areas with clear facets of wear and repeating the best fit alignment almost always resulted in a better fit compared to standard best fit alignment, which is also supported by previous literature15,17. It is important that only occlusal surfaces with wear are deselected so that as many coronal surfaces are available for the best fit procedure, hereafter called the &#34;modified reference based fit technique&#34;22. The difficulties with obtaining the best fit in this population explain the difference in precision between height and volume measurements. If the best fit procedure results in an imperfect alignment, this will affect the volume difference of the tooth relatively more than height measurements. Additionally, locations with artifacts such as saliva can be avoided in height measurements but not in volume measurements.
Selecting the point of the highest wear 
Some outliers remained despite training, caused by a variety of factors such as disagreements due to unclear anatomy, wear, or restorations, and were not preventable by adjusting the protocol. A point of improvement was achieved by editing the color spectrum depicting wear, which is shown as a blue area. By changing the spectrum, dark blue areas of wear could be decreased to a darkest blue point, pinpointing the location with the highest amount of wear, which decreased operator sensitivity in choosing the location of highest wear.
Measuring volume versus measuring height 
The precision of volume measurements was insufficient for clinical tooth wear measurement. This is due, firstly, to the aforementioned issue regarding the best fit. A slight deviation in the fit can result in a large difference between the superimposed teeth. Secondly, saliva, restorations, powder, and other possible artifacts are measured by the software as changes in volume, although they are not actual wear. Thirdly, the selection of the surface for volumetric changes might be influenced by tooth size, shape, and scanned surfaces. Fourthly, the software algorithm might be too imprecise when filling holes or calculating volume to precisely detect volume changes. Since calculating the volume change is done automatically after performing the best fit, the imprecision of volume measurements did not lead to modifications of the protocol other than improving the best fit. Theoretically, volumetric change measurement would be preferable, since volumetric changes are not affected by outliers in single data points or large sections of the area being unchanged by wear, like height measurements12,17. However, volumetric changes are dependent on tooth size, which should be considered when reporting volumetric change15. Additionally, height measurement may be useful for obtaining a good impression of the wear processes on the surface. It is vital for future research to focus on methods to accurately measure both height and volumetric changes to determine the progression of tooth wear.
Strengths and limitations of the protocol 
This protocol is based on a reproducible chairside method; therefore, the findings translate to what clinicians could expect when looking for a method to monitor wear using intra-oral scanners. The 3DWA protocol has been proven to be precise, and, additionally, the levels of wear found for patients with higher and lower progression of wear (Table 2) were similar to the ones found in literature, suggesting high accuracy as well4,5,7,8,9.
The limitations are also the limitations a clinician would face: patient-related factors such as limited mouth opening, the presence of saliva or scanning powder (depending on the type of scanner), and possible scanning artifacts or software errors resulting in random error (62 &#181;m on the surface level), which is quite substantial when compared to the amount of wear one might expect after a year in patients with severe tooth wear (between 68-140 &#181;m per year) or in patients with physiological wear of about 30 &#181;m per year4,5,6,7,8,9. However, the duplicate measurement error becomes far less significant when the range of wear increases, either due to a longer interval or more severe and quickly progressing tooth wear. Secondly, for research purposes, measurements can be repeated to reduce the DME. Thirdly, scanners and scanning systems are constantly revised and updated, and precision is only expected to increase in the future, which creates more possibilities for precise height and volume measurements.
Although the 3DWA protocol provides useful and reliable information on the progression of tooth wear in research, it is probably still too time-consuming and costly for application in standard clinical care. The software necessary for quantitative wear measurement is not readily available for researchers, let alone dental clinicians10. Comparing complete dentitions may take between 3 and 6 h, depending on the experience of the rater and the severity of the wear. Therefore, the authors feel that a vital next step in improving patient care is the automation of this validated 3DWA protocol, which would make it more time- and cost-efficient. Different approaches, such as the use of index teeth instead of measuring all teeth and cusps to determine the progression of wear, can also be used13.
The significance of the method with respect to existing/alternative methods 
This protocol provides more quantifiable, objective, and precise data on the progression of tooth wear compared to more commonly used quantitative methods such as the Tooth Wear Index (TWI), Tooth Wear Evaluation System (TWES), or Basic Erosive Wear Examination (BEWE)24,25,26. This is the first study done on all direct in vivo scans without using lab scanners or scanned impressions to assess the wear. In this study, adequate protocol precision and excellent intra-rater precision were found when measuring height. There was only a slight difference between raters, which would not result in patients being incorrectly diagnosed as having stable or progressive moderate to severe wear. This method was not able to provide precise volumetric change measurements, which previous research has argued to be more reliable, and, in that area, more research needs to be done15.
The identified protocol precision of 0.062 mm (random error, or DME) for height is not the only factor to consider when trying to determine the precision of the protocol for a given measurement. The systematic errors are minimal enough to dismiss; however, the random error of 0.062 is random and, therefore, not the same for every measurement. This excludes the existence of a simple threshold for minimum precision. In a research setting with many repeated measurements, the effect of the random error is minimal. In an individual patient, however, the random error comes into effect. The importance of a random error of 0.062 mm is dependent on which true value of height loss signifies pathological tooth wear. The chosen threshold combined with the DME determines the chance of a measurement measuring pathological tooth wear where there is none and vice versa. For example, for an individual patient, if a threshold of 0.070 mm of tooth wear per year is determined as being pathological, and 0.030 mm of tooth wear per year is considered physiological, a DME of 0.062 mm gives a 26% probability that the identified value is higher than 0.070 mm when the true value is 0.030 mm, thereby falsely classifying a patient as having pathological wear. However, after 3 years, the threshold for pathological wear would be 0.210 mm. Then, with a true value of 0.090 mm (per 3 years), there is only a 2.6% chance that the value found is higher than the threshold value. Therefore, the recommendation is to measure tooth wear after multiple years in patients with moderate wear, or at a shorter interval with higher suspected progression, in order to precisely determine individual wear.
Additionally, it is very difficult to compare the precision found with previously reported values. Although many studies have been performed on the precision and accuracy of scanners, the specific technique used in this study, scanning a full arch (which lowers precision) but comparing single teeth (which heightens the precision), makes it impossible to compare given values on full arches and single teeth18. In research conducted on the progression of tooth wear, the precision reported was based on in vitro findings on simulated wear or done with lasers or lab scanners, and, as such, is difficult to compare with findings of this study and less relevant in a clinical setting6,14,17,20,21.
Importance of application 
Overall, these findings indicate that quantitative wear measurement of intra-oral scans is an attainable and precise method to quantify the progression of wear in height. The result seems to be independent of the experience of the operator and limited training in the protocol. This has great advantages in research, such as being able to quantify and monitor wear and store information digitally in subject records. This protocol would be useful in clinical practice in the management of tooth wear to determine treatment options, create awareness, and improve patient-centered care. Although currently too time-consuming to perform, modified versions of the protocol for clinical practice, such as measuring index teeth instead of full dentitions, can alleviate this problem, as well as automation of the protocol. It will be an important step towards a future where patients will be scanned regularly as part of standard care, with software diagnosing areas with wear progression.

Tooth wear, though not life-threatening, can negatively impact patients&#39; quality of life, both physiologically and psychologically1. It can affect masticatory and esthetic function, as well as the quality of life. The severity of the impact depends on the etiology, progression, and presentation of the wear and can differ greatly between patients2. The impact of tooth wear is expected to increase in the future due to increased human life expectancy, lifestyle changes, and people retaining their natural teeth for longer3. Therefore, diagnosing tooth wear and quantifying the progression of tooth wear is of increasing importance in providing patient care.
Despite the importance of measuring tooth wear, in vivo quantitative data on the absolute amount of tooth wear is scarce. Findings on tooth wear progression are often contradictory due to great variation in the methodology used. Several studies have shown relatively low progression rates in patients with physiological wear, with reported height loss between 11 and 29 &#181;m per year and volume loss around 0.04 &#181;m3 per year4,5,6. In cases of advanced tooth wear or existing parafunctional habits, much higher progression rates were found, between 68 and 140 &#181;m per year7,8,9. These measurements were based on gypsum casts and gypsum cast dies and performed with either varying scanning and 3D subtraction software or microscopes. Since these methods are not available or practical in dental practice, they are not yet suitable for use in clinical care. However, intra-oral 3D scanning is rapidly becoming available in general dental practice, with advantages for both patient and operator with respect to speed and comfort of use, coupled with easy storage and data sharing10. 3D data can also be used for quantitative wear measurement, in which scans of teeth or jaws are superimposed and the difference between the scans is measured. This provides a quantitative option for measuring the progression of loss of tooth material in height or volume11,12.
Findings on the precision (closeness of agreement between replicated measurements) and accuracy (the difference between a measured quantity and its true value) have been variable when using scanners to detect and measure wear. Quantitative wear measurement has been reported as being a time-consuming method with often unknown or inadequate precision and accuracy, especially when dealing with minimal wear13,14. Others have reported intra-oral scanners to be precise enough to detect and monitor tooth wear, with superimposition reference areas (best fit) and software settings significantly affecting the outcome15,16.
Various methods have been used to find the best fit: 1) landmark alignment based on landmarks such as soft tissue, adjacent intact teeth, and alveolar processes, 2) standard best-fit alignment with the software minimizing the mesh distance error between data clouds, or 3) reference best-fit alignment with the best fit performed on a selection of areas chosen by the operator. It has been found that the reference best-fit alignment has the highest precision and accuracy15,17. Research shows that the precision and accuracy of a quantitative wear measurement increases when smaller structures, such as single teeth, are compared, instead of a full arch18,19. Two automated systems using 3D scans and quantitative wear measurement to monitor wear have been introduced; one has been tested in an in vitro setting on shortened arches or single teeth, while the other has indicated some promise for in vivo use for volumetric measurements compared to lab-scanned casts20,21,22. Most of these studies on accuracy and precision are based on scanned casts or in vitro simulated wear and are, therefore, not easily translated to clinical outcomes. Finding a clinically feasible protocol to perform quantitative wear measurements after intra-oral scanning in vivo would, therefore, be a vital next step in monitoring tooth wear15.
At the Radboud University Medical Center in Nijmegen, the Netherlands, a 3D Wear Analysis (3DWA) protocol using 3D measurement software has been developed to measure tooth wear in vivo using an intra-oral scanner on patients with moderate to severe tooth wear. Since it is nearly impossible to measure the accuracy in vivo, this article focuses on determining the precision of the 3DWA protocol. Particularly, this study aims to 1) describe the precision of the scanner and scanning process (acquisition) and subsequent superimposition by superimposing two scans of the same dentition acquired in the same session (protocol precision). Additionally, the 3DWA protocol was tested for 2) intra- and 3) inter-rater precision when measuring wear progression in both height (mm) and volume (mm3), on scans made at 0-3- or 0-5-year intervals. The scans were made intra-orally in patients with moderate to severe wear and the quantitative wear measurement was performed using the 3DWA protocol.
To test the agreement between raters with differing types of training, three raters were selected and trained. Rater 1 was a PhD student, who received extensive training on the execution of the 3DWA protocol and had 1 year of experience working on analyzing scans before independently executing the selected duplicate measurements. Rater 2 was a final year dental MSc student, who was given the protocol and an explanation of the software program and, thereafter, executed the protocol independently. Rater 3 was a dental MSc student, who received the protocol, an explanation of the software program, and two 3-h training sessions, after which she independently executed the protocol for the duplicate measurements. The raters did not have clinical information about the subjects other than the scans prior to the analysis. The scans were anonymized and coded before analysis by researchers other than the raters. When analyzing and measuring tooth wear, the old annotations from previous raters were hidden prior to analysis in the software. The measurements from the different raters were initially saved in different files.
A group of 55 patients was included from a larger prospective observational study on the progression of tooth wear of the Radboud Tooth Wear Project at the Department of Dentistry, Radboud University Medical Center, in Nijmegen (The Netherlands). These patients were scanned at intake, 1-year recall, 3-year recall, and 5-year recall. Descriptive statistics of the available scans from the group of 55 patients were calculated regarding tooth wear after 0-1-, 0-3-, and 0-5-year intervals for height (mm) and volume (mm3) to compare and interpret the results of the analysis of the precision of tooth wear in terms of clinical relevance.
To calculate the protocol precision, two patients were randomly chosen from the above-mentioned sample of 55 and asked for permission to have their dentition scanned twice with a 15 min break instead of once at a recall appointment. The 3DWA protocol was then executed by rater 1. Due to the high number of measurements of height and volume on two dentitions (respectively 65 for height and 16 for volume per dentition), this was deemed satisfactory to reliably estimate the precision. To calculate the precision within one rater (intra-rater: rater 1), one patient was selected with moderate wear and repeated 1 month later. To calculate the precision between raters (inter-raters: raters 1, 2 and 3), a convenience sample of four patients was selected, with two patients having moderate and two patients having severe wear progression. Intervals between the selected scans were either 3 or 5 years. The results between raters were calculated, comparing rater 1 with rater 2 and rater 1 with rater 3.

<table><tbody><tr><td>Dry Tips</td><td>Microbrush International</td><td>273-DTL</td><td>Dry pad to cover buccal mucosa</td></tr><tr><td>GeoMagic Qualify</td><td>3D Systems</td><td></td><td>Measurement, comparison and reporting software tool for first-article and automated inspection processes</td></tr><tr><td>High Resolution Scanning Spray Powder</td><td>3M ESPE</td><td>42295100</td><td>Powder to cover to-be scanned surfaces</td></tr><tr><td>High Resolution Sprayer</td><td>3M</td><td>42295100</td><td>Sprayer for scanning powder</td></tr><tr><td>Lava Chairside Oral Scanner</td><td>3M ESPE</td><td>68901</td><td>Intra Oral Scanner</td></tr><tr><td>Mobile True Definition Scanner</td><td>3M</td><td>M06-6060</td><td>Mobile Intra Oral Scanner</td></tr><tr><td>OptraGate</td><td>Ivoclar Vivadent</td><td>49294</td><td>Flexible lip and cheek retractor</td></tr><tr><td>Saliva Ejector HYGOFORMIC</td><td>Pulpdent</td><td>SV-6075</td><td>Intra Oral Scanning Aids in tongue retraction and suction for mandibular scanning</td></tr><tr><td>True Definition Scanner</td><td>3M</td><td>M06-6000</td><td>Intra Oral Scanner</td></tr></tbody></table>

precision of in vivo quantitative tooth wear measurement using intra-oral scans

Quantitative wear measurement is of increasing interest for measuring tooth wear progression. However, most research on quantitative wear measurement has focused on simulated wear or scanned gypsum casts. A 3D Wear Analysis (3DWA) protocol has been developed that analyzes tooth wear in vivo through intra-oral scanners available to dental clinicians. This study investigated the precision of the 3DWA protocol for measuring wear through maximum height loss (mm) and volume change (mm3). Observational prospective wear data from 55 patients were analyzed after 0-1-, 0-3-, and 0-5-year intervals to determine rates of wear, and convenience samples were chosen to test the protocol&#39;s precision on dentitions scanned twice in one sitting and its intra- and inter-rater precision on scans with 0-3- and 0-5-year intervals. Scans were made using intra-oral scanners (IOS) and superimposed using 3D measurement software. T-tests were performed to determine the structural and random error, and trimmed ranges were calculated to interpret the error. For protocol precision, the mean difference was 0.015 mm (-0.002; 0.032, p = 0.076) for height and -0.111 mm3 (-0.250; 0.023, p = 0.101) for volume. The duplicate measurement error was 0.062 mm for height and 0.268 mm3 for volume. The height measurements were precise enough to measure wear after intervals of 0-3 or 0-5 years; however, volume measurements were susceptible to procedural error and operator sensitivity. The 3DWA protocol is precise enough to adequately measure tooth height loss after intervals of a minimum of 3 years or in patients with severe wear progression, but it is not suited to measuring volumetric changes.

During data analysis, the maximum height difference between occlusal surfaces was measured. For molars, three or four cusps were measured, and, for premolars, two cusps were measured. For maxillary anterior teeth, the incisal edge and palatal surface were measured, and, for mandibular anterior teeth, the incisal edge was measured. This resulted in a maximum of 65 measured locations per dentition. The difference in the volume of the occlusal surface was measured on posterior teeth only, resulting in a maximum of 16 observations per dentition.
Teeth with restorations on more than 75% of the measured surface were excluded, as well as third molars. On surfaces with partial restorations, height was measured on the tooth material. Height differences clearly caused by artifacts such as pooling of saliva were either excluded as a surface, or the measurement was done elsewhere on the surface. Other reasons for exclusion of surfaces or teeth were teeth being absent, the best fit being insufficient, or the data being incomplete (large gaps in the scan). Negative outcomes (inverse wear or &#34;growth&#34;, which is clinically impossible) on included teeth and surfaces were not used for further statistical analysis except when calculating the protocol precision, for which the differences, both negative and positive, were noted.
Table 1: Results of the analysis of the precision of tooth wear measurements for height and volume. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/Table 1.xls" target="_blank">Please click here to download this Table.</a>
Precision: structural differences 
The data for protocol precision was visualized in violin plots (Figure 2 and Table 1). The data for intra- and inter-rater precision was visualized in Bland Altman plots (Figure 3 and Table 1). For height, a statistically significant difference was found between R1 and R3, which is clinically not significant, as can be seen from the entire confidence interval (ci) being close to 0. For volume, it is important to note that, for intra-rater precision, 50% of the teeth measured had to be excluded from analysis due to negative measurements (e.g., &#34;growth&#34;) indicating inoperability.
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/63680/63680fig02.jpg" /> 
Figure 2: Violin plots for (A) height (mm) and (B) volume (mm3) for protocol precision. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/63680fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/63680/63680fig03.jpg" /> 
Figure 3: Bland Alman plots for (A,D) intra-rater and (B,C,E,F) inter-rater precision for height (B-C) and volume (E-F). The continued line indicates mean difference, and the dotted lines indicate limits of agreement. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/63680fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Precision: random error 
Regarding the DME for height, there were similar DMEs for protocol precision and inter-rater precision and a much lower DME for intra-rater precision. The correlation was high and similar for inter-rater precision, very high for intra-rater precision, and could not be calculated for protocol precision. Training seemed to have little effect when looking at DME and correlation for height. Regarding volume, there were large differences between protocol precision, inter-rater precision, and intra-rater precision results.
In order to interpret the structural and random differences described in Table 1, it is important to know the range of height and volume measurements to be expected after multiple years in patients with moderate to severe wear, which are described in Table 2.
Table 2: Trimmed ranges derived from the larger group of wear patients at 0-1-, 0-3- and 0-5-year intervals and the mean difference and DME expressed in percentages of the trimmed range. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/Table 2.xls" target="_blank">Please click here to download this Table.</a>
Interpretation of results: 
Comparing the results for height to the trimmed range of wear seen in a group of 55 patients with moderate to severe tooth wear gave small structural differences (mean difference) for all intervals and all tests. For the DME, there were large differences between 0-1- and 0-3- or 0-5-intervals for all tests, indicating that, for short intervals (limited wear progression), the protocol is not precise enough, but, for longer intervals (or higher wear progression rates), the precision is adequate.
For volume, the structural differences were small on all intervals, except for the results comparing rater 1 and rater 3. For the DME, there were large differences between 0-1- and 0-3- or 0-5-intervals for all tests. Despite good results for protocol precision, there were large differences between operators, a high number of outliers, and many teeth excluded due to measured &#34;growth&#34;, indicating poor performance of the protocol regarding volume, even for longer intervals.
The difference between protocol precision and intra-precision is due to differences in method;&#160;to calculate protocol precision, the teeth were scanned in the same session. No wear took place between the scans, resulting in an excellent best fit. Therefore, the precision of height was determined mainly by droplets of saliva and scanning powder creating tiny spikes, causing a large height difference when measuring the highest point on the surface (Figure 4). To calculate intra-rater agreement, scans were used with a 5-year interval between them, resulting in the presence of wear that increases the difficulty of performing the best fit. However, only wear was measured, and suspected saliva/powder residuals or areas with possible restorations or flaring (distortion at scanned edges of the tooth; Figure 5) were avoided, thereby increasing precision.
Since volume is calculated for the whole occlusal area and not by localized measurements, it is much less affected by occasional droplets of saliva than height when measuring protocol precision. Intra-precision would be expected to be lower than protocol precision for volume, since it is affected by the best fit procedure, which, in turn, is made more difficult by wear taking place between scans. This affects the whole occlusal area of a tooth, and, additionally, areas with saliva, powder, restorations, and flaring cannot be deselected or ignored in contrast to when height is measured. However, the results for intra-rater precision and protocol precision for volume were similar due to a single outlier decreasing protocol precision.
When analyzing the height data on wear progression comparing rater 1 to rater 2, it became clear that, for height, a group of outliers could be attributed to two factors: 1) measurements on teeth with severe wear were made with the 2D Compare method (Step 3.2), instead of 3D compare (Step 3.1), and 2) a set of measurements was wrongly made on pooled saliva, which was mistaken for wear by rater 2 (Figure 6). The data was, therefore, split into 3 groups and analyzed separately: &#34;saliva&#34;, &#34;normal&#34;, and &#34;2D Compare&#34; (Figure 6A). Rater 3 (trained) made no measurements on pooled saliva, proving that training was successful in that regard (Figure 6B).
When comparing the heights from annotations (&#34;normal&#34;) and manual 2D measurements (2D Compare) for rater 1, the &#34;normal&#34; measurements had a mean height difference of 0.132 mm, with N = 223, a standard deviation of 0.112, and range: -0.001; 0.847, and the 2D Compare measurements had a mean height difference of 0.557 mm, with N = 5, a standard deviation of 0.160, and range: 0.351; 0.743, indicating that the 2D Compare measurements were in a higher range with a higher standard deviation than normal measurements
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/63680/63680fig04.jpg" /> 
Figure 4: Example of saliva spikes on teeth without wear (incisal yellow areas) and wear caused by artifacts (lingual blue area indicating either flaring or removed calculus). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/63680fig04large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/63680/63680fig05.jpg" /> 
Figure 5: Example of pooled saliva in fissures (blue) and saliva spike (red-orange) on mesio-palatal and buccal cusp. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/63680fig05large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 6" class="xfigimg" src="/files/ftp_upload/63680/63680fig06.jpg" /> 
Figure 6: Scatter plots for measurement of changes in height with colored dots indicating groups of measurements (&#34;saliva&#34;, &#34;normal&#34;, and &#34;2D Compare&#34;). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/63680/63680fig06large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Precision of In Vivo Quantitative Tooth Wear Measurement Using Intra-Oral Scans at JoVE.com

Precision of In Vivo Quantitative Tooth Wear Measurement Using Intra-Oral Scans

Quantitative wear measurement is a method of increasing importance in measuring tooth wear progression. We here describe a protocol, its precision, and its intra/inter-rater precision for the acquisition and superimposition of repeated in vivo scanned dentitions in patients with moderate to severe wear, reporting on both height and volume measurements.

Precision of In Vivo Quantitative Tooth Wear Measurement Using Intra-Oral Scans

Quantitative wear measurement is of increasing interest for measuring tooth wear progression. However, most research on quantitative wear measurement has ...

precision-vivo-quantitative-tooth-wear-measurement-using-intra-oral

Nanyang Technological University

Research

JoVE Journal

Medicine

2.7K Views.  Radboud University Medical Center. Quantitative wear measurement is a method of increasing importance in measuring tooth wear progression. We here describe a protocol, its precision, and its intra/inter-rater precision for the acquisition and superimposition of repeated in vivo scanned dentitions in patients with moderate to severe wear, reporting on both height and volume measurements. 

Video: Precision of In Vivo Quantitative Tooth Wear Measurement Using Intra-Oral Scans

Heterogeneity Mapping of Protein Expression in Tumors using Quantitative Immunofluorescence

Morphologic heterogeneity within an individual tumor is well-recognized by histopathologists in surgical practice. While this often takes the form of areas of distinct differentiation into recognized histological subtypes, or different pathological grade, often there are more subtle differences in phenotype which defy accurate classification (Figure 1). Ultimately, since morphology is dictated by the underlying molecular phenotype, areas with visible differences are likely to be accompanied by differences in the expression of proteins which orchestrate cellular function and behavior, and therefore, appearance. The significance of visible and invisible (molecular) heterogeneity for prognosis is unknown, but recent evidence suggests that, at least at the genetic level, heterogeneity exists in the primary tumor1,2, and some of these sub-clones give rise to metastatic (and therefore lethal) disease. 
Moreover, some proteins are measured as biomarkers because they are the targets of therapy (for instance ER and HER2 for tamoxifen and trastuzumab (Herceptin), respectively). If these proteins show variable expression within a tumor then therapeutic responses may also be variable. The widely used histopathologic scoring schemes for immunohistochemistry either ignore, or numerically homogenize the quantification of protein expression. Similarly, in destructive techniques, where the tumor samples are homogenized (such as gene expression profiling), quantitative information can be elucidated, but spatial information is lost. Genetic heterogeneity mapping approaches in pancreatic cancer have relied either on generation of a single cell suspension3, or on macrodissection4. A recent study has used quantum dots in order to map morphologic and molecular heterogeneity in prostate cancer tissue5, providing proof of principle that morphology and molecular mapping is feasible, but falling short of quantifying the heterogeneity. Since immunohistochemistry is, at best, only semi-quantitative and subject to intra- and inter-observer bias, more sensitive and quantitative methodologies are required in order to accurately map and quantify tissue heterogeneity in situ.
We have developed and applied an experimental and statistical methodology in order to systematically quantify the heterogeneity of protein expression in whole tissue sections of tumors, based on the Automated QUantitative Analysis (AQUA) system6. Tissue sections are labeled with specific antibodies directed against cytokeratins and targets of interest, coupled to fluorophore-labeled secondary antibodies. Slides are imaged using a whole-slide fluorescence scanner. Images are subdivided into hundreds to thousands of tiles, and each tile is then assigned an AQUA score which is a measure of protein concentration within the epithelial (tumor) component of the tissue. Heatmaps are generated to represent tissue expression of the proteins and a heterogeneity score assigned, using a statistical measure of heterogeneity originally used in ecology, based on the Simpson's biodiversity index7.
To date there have been no attempts to systematically map and quantify this variability in tandem with protein expression, in histological preparations. Here, we illustrate the first use of the method applied to ER and HER2 biomarker expression in ovarian cancer. Using this method paves the way for analyzing heterogeneity as an independent variable in studies of biomarker expression in translational studies, in order to establish the significance of heterogeneity in prognosis and prediction of responses to therapy.

Here we describe a method to quantify molecular heterogeneity in histological sections of tumor material using quantitative immunofluorescence, image analysis, and a statistical measure of heterogeneity. The method is intended for use in clinical biomarker development and analysis.

Morphologic heterogeneity within an individual tumor is well-recognized by histopathologists in surgical practice. While this often takes the form of ...

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint

This study demonstrates a novel biomechanics testing protocol. The advantage of this protocol includes the use of an in situ loading device coupled to a high resolution X-ray microscope, thus enabling visualization of internal structural elements under simulated physiological loads and wet conditions. Experimental specimens will include intact bone-periodontal ligament (PDL)-tooth fibrous joints. Results will illustrate three important features of the protocol as they can be applied to organ level biomechanics: 1) reactionary force vs. displacement: tooth displacement within the alveolar socket and its reactionary response to loading, 2) three-dimensional (3D) spatial configuration and morphometrics: geometric relationship of the tooth with the alveolar socket, and 3) changes in readouts 1 and 2 due to a change in loading axis, i.e. from concentric to eccentric loads. Efficacy of the proposed protocol will be evaluated by coupling mechanical testing readouts to 3D morphometrics and overall biomechanics of the joint. In addition, this technique will emphasize on the need to equilibrate experimental conditions, specifically reactionary loads prior to acquiring tomograms of fibrous joints. It should be noted that the proposed protocol is limited to testing specimens under ex vivo conditions, and that use of contrast agents to visualize soft tissue mechanical response could lead to erroneous conclusions about tissue and organ-level biomechanics.

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint

In this study, the use of an in situ loading device coupled with micro-X-ray computed tomography for fibrous joint biomechanics will be discussed. Experimental readouts identifiable with an overall change in joint biomechanics will include: 1) reactionary force vs. displacement, i.e. tooth displacement within the alveolar socket and its reactionary response to loading, 2) three-dimensional (3D) spatial configuration and morphometrics, i.e.&#160;geometric relationship of the tooth with the alveolar socket, and 3) changes in readouts 1 and 2 due to a change in loading axis, i.e. concentric or eccentric loads.

This study demonstrates a novel biomechanics testing protocol. The advantage of this protocol includes the use of an in situ loading device coupled to a ...

Bioengineering

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation

Polymerization shrinkage of dental resin composites can lead to restoration debonding or cracked tooth tissues in composite-restored teeth. In order to understand where and how shrinkage strain and stress develop in such restored teeth, Digital Image Correlation (DIC) was used to provide a comprehensive view of the displacement and strain distributions within model restorations that had undergone polymerization shrinkage.
Specimens with model cavities were made of cylindrical glass rods with both diameter and length being 10 mm. The dimensions of the mesial-occlusal-distal (MOD) cavity prepared in each specimen measured 3 mm and 2 mm in width and depth, respectively. After filling the cavity with resin composite, the surface under observation was sprayed with first a thin layer of white paint and then fine black charcoal powder to create high-contrast speckles. Pictures of that surface were then taken before curing and 5 min after. Finally, the two pictures were correlated using DIC software to calculate the displacement and strain distributions.
The resin composite shrunk vertically towards the bottom of the cavity, with the top center portion of the restoration having the largest downward displacement. At the same time, it shrunk horizontally towards its vertical midline. Shrinkage of the composite stretched the material in the vicinity of the &#8220;tooth-restoration&#8221; interface, resulting in cuspal deflections and high tensile strains around the restoration. Material close to the cavity walls or floor had direct strains mostly in the directions perpendicular to the interfaces. Summation of the two direct strain components showed a relatively uniform distribution around the restoration and its magnitude equaled approximately to the volumetric shrinkage strain of the material.

In order to understand the spatial development of polymerization shrinkage stress in dental resin-composite restorations, Digital Image Correlation was used to provide full-field displacement/strain measurement of restored model glass cavities by correlating images of the restoration taken before and after polymerization.

Polymerization shrinkage of dental resin composites can lead to restoration debonding or cracked tooth tissues in composite-restored teeth. In order to ...

Measuring the Complete-arch Distortion of an Optical Dental Impression

Digital workflows have actively been used to produce dental restorations or oral appliances since dentists started to make digital impressions by acquiring 3D images with an intraoral scanner. Because of the nature of scanning the oral cavity in the patient&#39;s mouth, the intraoral scanner is a handheld device with a small optical window, stitching together small data to complete the entire image. During the complete-arch impression procedure, a deformation of the impression body can occur and affect the fit of the restoration or appliance. In order to measure these distortions, a master specimen was designed and produced with a metal 3D printer. Designed reference geometries allow setting independent coordinate systems for each impression and measure x, y, and z displacements of the cylinder top circle center where the distortion of the impression can be evaluated. In order to evaluate the reliability of this method, the coordinate values of the cylinder are calculated and compared between the original computer-aided design (CAD) data and the reference data acquired with the industrial scanner. The coordinate differences between the two groups were mostly less than 50 &#181;m, but the deviations were high due to the tolerance of 3D printing in the z coordinates of the obliquely designed cylinder on the molar. However, since the printed model sets a new standard, it does not affect the results of the test evaluation. The reproducibility of the reference scanner is 11.0 &#177; 1.8 &#181;m. This test method can be used to identify and improve upon the intrinsic problems of an intraoral scanner or to establish a scanning strategy by measuring the degree of distortion at each part of the complete-arch digital impression.

Here, we present a protocol to measure the degree of distortion at each part of the compete-arch digital impression acquired from an intraoral scanner with 3D-printed metal phantom with standard geometries.

Digital workflows have actively been used to produce dental restorations or oral appliances since dentists started to make digital impressions by ...

Engineering

Accuracy in Dental Medicine, A New Way to Measure Trueness and Precision

Reference scanners are used in dental medicine to verify a lot of procedures. The main interest is to verify impression methods as they serve as a base for dental restorations. The current limitation of many reference scanners is the lack of accuracy scanning large objects like full dental arches, or the limited possibility to assess detailed tooth surfaces. A new reference scanner, based on focus variation scanning technique, was evaluated with regards to highest local and general accuracy. A specific scanning protocol was tested to scan original tooth surface from dental impressions. Also, different model materials were verified. The results showed a high scanning accuracy of the reference scanner with a mean deviation of 5.3 &#177; 1.1 &#181;m for trueness and 1.6 &#177; 0.6 &#181;m for precision in case of full arch scans. Current dental impression methods showed much higher deviations (trueness: 20.4 &#177; 2.2 &#181;m, precision: 12.5 &#177; 2.5 &#181;m) than the internal scanning accuracy of the reference scanner. Smaller objects like single tooth surface can be scanned with an even higher accuracy, enabling the system to assess erosive and abrasive tooth surface loss. The reference scanner can be used to measure differences for a lot of dental research fields. The different magnification levels combined with a high local and general accuracy can be used to assess changes of single teeth or restorations up to full arch changes.

Accuracy is a major demand in dental medicine. To verify accuracy, reference scanners are needed. This article presents a new reference scanner with an adjusted scanning method to acquire a broad variety of dental morphologies with high trueness and precision.

Reference scanners are used in dental medicine to verify a lot of procedures. The main interest is to verify impression methods as they serve as a base ...

Mimicking and Measuring Occlusal Erosive Tooth Wear with the "Rub&amp;Roll" and Non-contact Profilometry

Chewing, drinking, and occasional tooth grinding will result in physiological tooth wear during a lifetime. Extreme challenges, such as bruxism or habitual chewing on foreign objects, may lead to excessive wear. Recently, the role of erosion in accelerating mechanical tooth wear has been recognized, but the interplay between chemical and mechanical wear processes has not been extensively studied. Our laboratory recently introduced a novel oral wear simulation device, the Rub&#38;Roll, that enables the user to perform wear and loading studies separately or simultaneously in an erosive and/or abrasive environment. This manuscript describes an application of the device: the combined mechanical and erosive loading of extracted human (pre)molars in a simulated chewing movement, with a controlled application of force, velocity, fluid, and time, and the application of non-contact profilometry in visualizing and measuring the resulting wear pattern. The occlusal morphology that was created in the experiment with the highest loading level is very similar to the clinical presentation of erosive wear.

Mimicking and Measuring Occlusal Erosive Tooth Wear with the "Rub&Roll" and Non-contact Profilometry

The Rub&#38;Roll can mimic the chewing cycle, allowing variation of chewing force, sliding distance, chewing velocity, number of cycles, and frequency, and with a combination of erosive and abrasive challenges can result in a complex simulation of oral ageing.

Chewing, drinking, and occasional tooth grinding will result in physiological tooth wear during a lifetime. Extreme challenges, such as bruxism or ...

Digital Hybrid Model Preparation for Virtual Planning of Reconstructive Dentoalveolar Surgical Procedures

Virtual, hybrid three-dimensional (3D) model acquisition is presented in this article, utilizing the sequence of radiographic image segmentation, spatial registration, and free-form surface modeling. Firstly cone-beam computed tomography datasets were reconstructed with a semi-automatic segmentation method. Alveolar bone and teeth are separated into different segments, allowing 3D morphology, and localization of periodontal intrabony defects to be assessed. The severity, extent, and morphology of acute and chronic alveolar ridge defects are validated concerning adjacent teeth. On virtual complex tissue models, positions of dental implants can be planned in 3D. Utilizing spatial registration of IOS and CBCT data and subsequent free-form surface modeling, realistic 3D hybrid models can be acquired, visualizing alveolar bone, teeth, and soft tissues. With the superimposition of IOS and CBCT soft tissue, thickness above the edentulous ridge can be assessed about the underlying bone dimensions; therefore, flap design and surgical flap management can be determined, and occasional complications may be avoided.

A workflow for creating three-dimensional (3D) virtual hybrid models has been designed based on cone-beam computed tomography dataset and intraoral optical scans utilizing radiographic image segmentation methods and free-form surface modeling. Digital models are used for the virtual planning of reconstructive dentoalveolar surgical procedures.

Virtual, hybrid three-dimensional (3D) model acquisition is presented in this article, utilizing the sequence of radiographic image segmentation, spatial ...

Semi-Automated Planimetric Quantification of Dental Plaque Using an Intraoral Fluorescence Camera

Dental plaque accumulation is quantified using clinical indices or, otherwise, the planimetric plaque index (PPI),&#160;which measures the relative area of a tooth that is covered by plaque deposits. Compared to clinical indices, the PPI has a higher discriminatory power, but traditional planimetry is a time-consuming analysis, as the plaque-covered and clean tooth areas have to be determined manually for each image using image-processing software. Here, we present a method for the semi-automated planimetric quantification of dental plaque, which allows for the rapid processing of up to 1,000 images simultaneously. The method exploits the enhanced contrast between disclosed plaque, sound tooth surfaces, and soft tissues in fluorescence images acquired with an intraoral camera. Careful execution of the clinical procedures and accurate image acquisition are crucial steps for the successful semi-automated identification of the plaque-covered areas. The method is suitable for planimetry on sound facial and oral tooth surfaces, on most composite resin restorations, and on teeth with orthodontic brackets, but not on metallic restorations. Compared to traditional PPI recordings, semi-automated planimetry considerably reduces the amount of time spent on the analysis, as well as the subjective human input, thus increasing the reproducibility of planimetric measurements.

This study presents a semi-automated digital image analysis procedure for the planimetric quantification of disclosed dental plaque based on images acquired with an intraoral fluorescence camera. The method allows for the rapid and reliable quantification of dental plaque in the research environment.

Dental plaque accumulation is quantified using clinical indices or, otherwise, the planimetric plaque index (PPI),&#160;which measures the relative area ...

Evaluation of Maxillary Posterior Tooth Movement Using Digital Superimposition

Measuring Maxillary Posterior Tooth Movement: A Model Assessment using Palatal and Dental Superimposition

Since the introduction of Invisalign by Align Technology, Inc. in 1999, questions and debates have persisted regarding the precision of Invisalign (clear aligner) therapy, particularly when compared to the use of traditional fixed appliances. This becomes particularly significant in cases involving anteroposterior, vertical, and transverse corrections, where precise comparisons are of paramount importance. To address these inquiries, this study introduces a meticulously devised protocol, placing a primary emphasis on digitally superimposing the movement of maxillary posterior teeth to facilitate accurate analysis. The sample included 25 patients who had completed their first series of Invisalign (clear) aligners. Four maxillary digital models (pre-treatment, post-treatment, ClinCheck-initial, and final models) were digitally superimposed using the palate rugae and dentitions as stable references. A software combination was used for model superimposition and tooth segmentation. Transformation matrices then expressed the differences between the achieved and predicted tooth positions. Thresholds for clinically relevant differences were at &plusmn;0.25 mm for linear displacement and &plusmn;2&#176; for rotation. Differences were assessed using Hotelling's T-squared tests with Bonferroni correction. The mean differences in rotation (2.036&#176; &plusmn; 4.217&#176;) and torque (-2.913&#176; &plusmn; 3.263&#176;) were significant statistically and clinically, with p-values of 0.023 and 0.0003 respectively. De-rotation of premolars and torque control for all posterior teeth were less predictable. All mean differences for the linear measurements were statistically and clinically insignificant, except that the first molars seemed slightly (0.256 mm) more intruded than their predicted position. The clear aligner system appears to meet its prediction for most translational tooth movements and mesial-distal tipping in maxillary posterior teeth for non-extraction cases with mild to moderate malocclusions.

Author Spotlight: 3D Movement Assessment of Maxillary Posterior Teeth in Clear Aligner Treatment

This manuscript presents a comprehensive protocol to evaluate the three-dimensional (3D) movement of maxillary posterior teeth with clear aligners using digital model superimposition, an invaluable tool in orthodontics and dentofacial orthopedics.

Since the introduction of Invisalign by Align Technology, Inc. in 1999, questions and debates have persisted regarding the precision of Invisalign (clear ...

Microhardness Protocol for Evaluating Rodent Oral Disease

Microhardness Measurements on Tooth and Alveolar Bone in Rodent Oral Disease Models

The mechanical property, microhardness, is evaluated in dental enamel, dentin, and bone in oral disease models, including dental fluorosis and periodontitis. Micro-CT (&#181;CT) provides 3D imaging information (volume and mineral density) and scanning electron microscopy (SEM) produces microstructure images (enamel prism and bone lacuna-canalicular). Complementarily to structural analysis by &#181;CT and SEM, microhardness is one of the informative parameters to evaluate how structural changes alter mechanical properties. Despite being a useful parameter, studies on microhardness of alveolar bone in oral diseases are limited. To date, divergent microhardness measurement methods have been reported. Since microhardness values vary depending on the sample preparation (polishing and flat surface) and indentation sites, diverse protocols can cause discrepancies among studies. Standardization of the microhardness protocol is essential for consistent and accurate evaluation in oral disease models. In the present study, we demonstrate a standardized protocol for microhardness analysis in tooth and alveolar bone. Specimens used are as follows: for the dental fluorosis model, incisors were collected from mice treated with/without fluoride-containing water for 6 weeks; for ligature-induced periodontal bone resorption (L-PBR) model, alveolar bones with periodontal bone resorption were collected from mice ligated on the maxillary 2nd molar. At 2 weeks after the ligation, the maxilla was collected. Vickers hardness was analyzed in these specimens according to the standardized protocol. The protocol provides detailed materials and methods for resin embedding, serial polishing, and indentation sites for incisors and alveolar. To the best of our knowledge, this is the first standardized microhardness protocol to evaluate the mechanical properties of tooth and alveolar bone in rodent oral disease models.

Author Spotlight: Establishing an Accurate Microhardness Testing Protocol for Craniofacial Tissues

Microhardness is a mechanical property and an informative parameter for evaluating hard tissue pathophysiology. Here, we demonstrate a standardized protocol (sample preparation, polishing, flat surface, and indentation sites) for microhardness analysis in tooth and alveolar bone in rodent oral disease models, namely, dental fluorosis, and ligature-induced periodontal bone resorption.

Precision of In Vivo Quantitative Tooth Wear Measurement Using Intra-Oral Scans

Podsumowanie

Przeglądaj więcej filmów

Rozdziały w tym wideo

Heterogeneity Mapping of Protein Expression in Tumors using Quantitative Immunofluorescence

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation

Measuring the Complete-arch Distortion of an Optical Dental Impression

Accuracy in Dental Medicine, A New Way to Measure Trueness and Precision

Mimicking and Measuring Occlusal Erosive Tooth Wear with the "Rub&Roll" and Non-contact Profilometry

Digital Hybrid Model Preparation for Virtual Planning of Reconstructive Dentoalveolar Surgical Procedures

Semi-Automated Planimetric Quantification of Dental Plaque Using an Intraoral Fluorescence Camera

Measuring Maxillary Posterior Tooth Movement: A Model Assessment using Palatal and Dental Superimposition

Microhardness Measurements on Tooth and Alveolar Bone in Rodent Oral Disease Models