We would like to thank the two anonymous reviewers for their suggestions. Funding for this research was provided by Agriculture and Agri-Food Canada (AAFC) under project J-002295 (Management and enhancement of AAFC&#39;s biological collections).

1. Modification of two-compartment Petri dishes
NOTE: The materials required for this step are listed in the Table of Materials.
<ol>
	<li>Modify the Petri dish lid.
	<ol>
		<li>Using the rotary tool and appropriate carving bit, drill two holes (~7 mm in diameter) in the top of the lid and a 1 cm opening in the side. One hole will be used to irrigate the root (vermiculite) compartment and the other for the hyphae (SAP) compartment.</li>
	</ol>
	</li>
	<li>Modify the Petri dish bottom.
	<ol>
		<li>Drill a notch in the side of the Petri dish bottom for the plant stem using the electric rotary tool. Make sure the notch is not too deep to prevent the liquid from draining. This notch will align with the 1 cm opening in the lid (step 1.1).</li>
		<li>To replace the plastic barrier of the dual-compartment Petri dish with the nylon mesh filter membrane, use the electric rotary tool to drill a 30 mm rectangular notch down to the bottom of the Petri dish.</li>
		<li>For high-resolution observation, drill circular holes ~25 mm in diameter in the bottom of the Petri dish. Depending on requirements, make a single hole (or multiple holes) on the SAP side or one in each compartment. Ensure that the holes are not drilled directly under the irrigation holes of the lid.</li>
	</ol>
	</li>
	<li>Install nylon mesh filter membrane.
	<ol>
		<li>Use the metal guide and paper clip to wedge the piece of the nylon mesh filter membrane in place and press it firmly onto the plastic barrier. Align the top of the membrane with the top of the plastic barrier. Make sure the membrane protrudes from the bottom of the guide.</li>
		<li>Using the pyrography kit, cut along the edge of the metal guide to melt and seal the membrane to the bottom of the Petri dish and the plastic barrier separating the two compartments.</li>
		<li>With the metal guide and paper clip still in place, carefully remove excess nylon mesh filter membrane with tweezers.</li>
		<li>Verify under the dissecting microscope that the nylon mesh filter membrane is properly sealed to the plastic to prevent root penetration into the hyphal (SAP) compartment.</li>
	</ol>
	</li>
	<li>Install coverslip. 
	NOTE: The coverslip is placed under the Petri dish. This allows the immersion oil to be used and the coverslip to be cleaned.
	<ol>
		<li>Place the silicone sealant along the edge of the circular holes (outside the Petri dish bottom).</li>
		<li>Place the coverslip on the outside of the Petri dish bottom and gently press to ensure perfect adhesion.</li>
		<li>Allow to dry, and remove excess sealant with a razor blade.</li>
	</ol>
	</li>
	<li>Inspect and clean.
	<ol>
		<li>Use an air blast to remove any dust or pieces of plastic that may have adhered to the Petri dish.</li>
		<li>Inspect under a dissecting microscope to identify and correct any defects. 
		NOTE: Wear gloves to avoid fingerprints on the Petri dishes</li>
	</ol>
	</li>
</ol>
2. Preparation of 1 L of nutrient solution mMS-1
<ol>
	<li>Prepare stock solutions.
	<ol>
		<li>Macronutrients: Weigh and dissolve the following in 1 L of distilled water: 
		7.31 g of MgSO4&#183;7 H2O, 0.80 g of KNO3, 0.65 g of KCl, and 0.048 g of KH2PO4,.</li>
		<li>Weigh 2.88 g of Ca(NO3)2&#183;4H2O and dissolve in 1 L of distilled water.</li>
		<li>Weigh 0.80 g of NaFeEDTA and dissolve in 0.5 L of distilled water.</li>
		<li>Weigh 0.375 g of KI and dissolve in 0.5 L of distilled water.</li>
		<li>Micronutrients
		<ol>
			<li>Dissolve 3 g of MnCl2&#183;4H2O in 100 mL of distilled water.</li>
			<li>Dissolve 1.325 g of ZnSO4&#183;7H2O in 100 mL of distilled water.</li>
			<li>Dissolve 0.75 g of H3BO3 in 100 ml of distilled water.</li>
			<li>When dissolved, mix the solutions prepared in steps 2.1.5.1-2.1.5.3.</li>
			<li>Weigh 0.65 g of CuSO4&#183;5H2O and dissolve in 50 mL of distilled water.</li>
			<li>Dissolve 0.12 g of Na2MoO4&#183;2H2O in 100 mL of distilled water.</li>
			<li>Add 5 mL of the solution from step 2.1.5.5 and 1 mL from step 2.1.5.6 to the solution from step 2.1.5.4.</li>
			<li>Adjust the volume of the solution obtained in step 2.1.5.7 to 500 mL with distilled water.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Prepare 1 L of mMS-1 media.
	<ol>
		<li>Add 700 mL of distilled water to a 2 L glass bottle.</li>
		<li>While constantly stirring with a magnetic bar, add 100 mL of macronutrients solution (step 2.1.1), 100 mL of calcium nitrate solution (step 2.1.2), 5 mL of ferric EDTA solution (step 2.1.3), 1 mL of KI solution (step 2.1.4), and 1 mL of micronutrients solution (step 2.1.5).</li>
		<li>Adjust the volume of the solution to 1000 mL. 
		NOTE: mMS-1 is adapted from B&#233;card and Fortin (1988)14. Sterilization at 121 &#176;C for 15 min is optional as the SAP-AS is not sterile. pH is not adjusted because the SAP has a strong buffering effect, and Par&#233; et al. (2022)12 showed that the conditions on SAP were relatively neutral (6.7 to 7.4).</li>
	</ol>
	</li>
</ol>
3. Preparation of SAP
NOTE: The materials required for this step are listed in the Table of Materials.
<ol>
	<li>Hydrate SAP: mix 5 g of dry SAP with 500 mL of mMS-1 nutrient solution (step 2.2).</li>
	<li>Allow to hydrate for 12 h (overnight) at room temperature (RT).</li>
	<li>Drain and collect the hydrated SAP grains.
	<ol>
		<li>When hydrated SAP is used to fill the 12-well plate (section 7), do not drain the hydrated SAP and mix the hydrated grain and the leftover of mMS-1 nutrient solution. 
		NOTE: Three granulometries of the dry SAP are available: small, medium, and large. The medium granulometry (1-2 mm) is the most appropriate. The SAP of large granulometry swallows too much when hydrated and the Petri dish lid cannot be closed, while the small granulometry SAP leaves little space between them, which is a limitation for the observations of the fungal structure between the grains.</li>
	</ol>
	</li>
</ol>
4. Preparation of seedlings
NOTE: The materials required for this step are listed in the Table of Materials.
<ol>
	<li>Germinate the seeds of P. lanceolata on blotting paper moistened with mMS-1 nutrient solution in a Petri dish.</li>
	<li>Incubate in the dark at RT.</li>
	<li>Rehydrate as needed until rootlets are at least 2 cm long.</li>
</ol>
5. Assembly and management of SAP-AS
NOTE: The materials required for this step are listed in the Table of Materials.
<ol>
	<li>Assemble SAP-AS (step 1 + step 2 + step 3 + step 4)
	<ol>
		<li>Place the seedling stem in the notch on the side of the Petri dish with the root inward and the cotyledons/leaves and stems outward.&#160;</li>
		<li>Cover the roots with approximately 1.5-2 g of vermiculite.</li>
		<li>Hydrate the root compartment with 8 mL of mMS-1 nutrient solution. This will help stabilize the root and vermiculite.</li>
		<li>Add 5 g of hydrated SAP along the nylon mesh filter membrane on the side of the root compartment.</li>
		<li>Add 15 g of hydrated SAP to the hyphal compartment. The hyphal compartment is the compartment with no notch on the side of the Petri dish bottom.</li>
		<li>Before closing the Petri dish with the lid, make sure that the side notches of the lid and the Petri dish bottom are aligned so as not to damage the stem.</li>
		<li>Seal the Petri dish with a strip of paraffin that joins the base and lid, taking care not to crush the young stem.</li>
		<li>Weigh and record the average weight of the Petri dish to determine when the SAP-AS needs to be rehydrated.</li>
		<li>Stack&#160;the Petri dishes to optimize space. Keep the Petri dish in the dark using an opaque cover with an opening on the side for the seedlings.</li>
	</ol>
	</li>
	<li>Manage SAP-AS.
	<ol>
		<li>Hydrate the Petri dishes with mMS-1 nutrient solution only.</li>
		<li>Use the average weight as a reference. When the Petri dish has lightened by 5-6 g, add mMS-1 nutrient solution to bring it back to the original weight. Ensure that the vermiculite and SAP are kept hydrated but not flooded. Roots must have access to oxygen.</li>
		<li>As the seedling and its fungal partner develop, irrigate them more frequently. It is not necessary to water both compartments at the same time. Irrigation requirements vary according to seedling development, but also according to the environmental conditions in which SAP-AS are incubated.</li>
		<li>Reduce the irrigation requirements by removing old leaves if the plant has more than three healthy leaves. Remove dead leaves. 
		NOTE: The presence of cations such as K+, Mg2+, and Ca2+ in the mMS-1 nutrient solution tends to decrease the expansion of the SAP network13 through time.</li>
	</ol>
	</li>
</ol>
6. Inoculation of the SAP-AS with a single spore
NOTE: The materials required for this step are listed in the Table of Materials.
<ol>
	<li>Inoculate with a single spore.
	<ol>
		<li>Heat the glass pipette with a flame candle or Bunsen burner. Pull as the glass melts to stretch the glass tube until it separates.</li>
		<li>Under a stereomicroscope, break the tip of the glass pipette to reduce the internal diameter (typically 100-300 &#181;m). This will greatly facilitate the manipulation of individual spores.</li>
		<li>Open the Petri dish, locate the spot where the spore is to be placed, and clear a space among the 5 g of hydrated SAP along the nylon mesh filter membrane to expose a section of a root.</li>
		<li>Under the dissecting microscope, pick up a spore with the extruded pipette. Pipette some liquid before pipetting the spore. Avoid pipetting liquid after collecting the spore.</li>
		<li>Under the dissecting microscope, carefully deposit the spore on the root. The liquid pipetted before pipetting the spore will help to expel the spore. If the spore is not deposited in an optimal place, use an acupuncture needle or brush hair to bring the spore back into contact with the root. If necessary, take a photo of the spore deposited on the root for reference and use a marker to locate the inoculation site.</li>
		<li>Replace the SAP over the root fragment to provide a moist microenvironment for the root and spore. Wait at least 24 h before irrigating the root compartment, and be careful not to wash the spore off the root.</li>
		<li>Before closing the Petri dish with the lid, make sure that the side notches of the lid and the bottom of the Petri dish are aligned so as not to damage the stem of the seedling. 
		NOTE: The SAP-AS is ready for inoculation when the roots reach the nylon mesh filter membrane, ideally a few days after irrigation, so there is no free liquid.</li>
	</ol>
	</li>
</ol>
7. Spore germination on SAP (optional)
NOTE: The materials required for this step are listed in the Table of Materials.
<ol>
	<li>Germination of spores.
	<ol>
		<li>Blend the hydrated SAP to obtain a smooth texture (see step 3.3.1). Air bubbles usually disappear within 24 h or by autoclaving (optional) the blended SAP.</li>
		<li>Using a 20 mL syringe without a needle, pipette approximately 2 g (equivalent to 2 mL) of blended SAP into each well of the 12-well plate.</li>
		<li>Select a spore under the dissecting microscope and use the extruded pipette as described in section 6.</li>
		<li>Under the dissecting microscope, place a spore in the center of each well.</li>
		<li>Incubate the 12-well plate in the dark at RT and monitor germination periodically.</li>
		<li>Under the dissecting microscope, select a spore with a growing hypha (at least a few millimeters in length).</li>
		<li>Add 1 mL of mMS-1 nutrient solution to the well and wait a few minutes for the medium to become more fluid.</li>
		<li>If necessary, use the acupuncture needle to gently remove the spore and hyphae from the substrate.</li>
		<li>Collect the spore either with a pipette or by bringing the roots of a seedling to the surface of the medium in order to stick the spore and hyphae to the roots. Then, place the seedling in the Petri dish as described in step 5.1.3. 
		NOTE: Coordinate spore germination and seedling growth. This method has only been tested with R. irregularis spores.</li>
	</ol>
	</li>
</ol>
8. Live monitoring of symbiosis development
NOTE: The materials required for this step are listed in the Table of Materials.
<ol>
	<li>Routinely observe with a dissecting, upright, or inverted microscope.
	<ol>
		<li>Observe the top of each compartment at 20x &#8211; 40x using a dissecting microscope with white illumination and dark field.</li>
		<li>If an inverted microscope is not available, observe the bottom of each compartment with a dissecting or upright microscope by inverting the Petri dish. Before inverting the Petri dish, allow the SAP-AS to dry for 2 days so that the SAP adheres slightly to the bottom of the Petri dish.</li>
		<li>Make detailed observations at 40x through the bottom of the Petri dish and up to 100x (oil immersion) through the coverslip.</li>
	</ol>
	</li>
	<li>Observe spores and hyphal networks. 
	NOTE: The fungal structures developing inside the SAP grains can be stained.
	<ol>
		<li>Prepare an ink and vinegar solution according to Vierheilig et al. (1998)15. Do not heat.</li>
		<li>Extract a SAP grain containing hyphae and spores and place it in the ink at RT. The ink will penetrate the SAP grain and stain the hyphae and spores within a few minutes.</li>
		<li>Remove the SAP grain and place it in mMS-1 nutrient solution or tap water. The ink will come out of the grain within&#160;12 h, but the spores and hyphae will remain stained.</li>
		<li>Press the SAP grain between two microscope slides to flatten it for photography and spore counting.</li>
	</ol>
	</li>
	<li>Observe arbuscules.
	<ol>
		<li>Extract a few roots from the root compartment and stain using the ink and vinegar protocol according to Vierheilig et al. (1998)15. Be careful not to immerse the roots in the KOH solution for more than 2-3 min; otherwise, the roots will become too fragile for the following steps and disintegrate into unusable debris.</li>
		<li>Under a dissecting microscope, select a root fragment approximately 5 mm long that may contain arbuscules and place it on a slide in a drop of water.</li>
		<li>Using acupuncture needles or extremely thin tweezers, tear off the roots in layers a few cells thick.</li>
		<li>Absorb the water and check under the microscope that the segments with arbuscules are still present and of satisfactory quality, and correctly placed on the slide. At this point, the arbuscules must be easily visible within the root cell layers.</li>
		<li>Allow drying for 2-3 min so the root layers adhere to the slide. Add a drop of polyvinyl alcohol-lactic acidglycerol (PVLG) buffer, and add the coverslip. Observe by standard microscopy methods.</li>
	</ol>
	</li>
</ol>

Culturing Arbuscular Mycorrhizal Fungi Using SAP-AS for Enhanced Observation

<ol>
	<li>Dotzler, N., Krings, M., Taylor, T. N., Agerer, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Germination+shields+in+Scutellospora+(Glomeromycota:+Diversisporales,+Gigasporaceae)+from+the+400+million-year-old+Rhynie+chert.">Germination shields in Scutellospora (Glomeromycota: Diversisporales, Gigasporaceae) from the 400 million-year-old Rhynie chert.</a> Mycol Prog. 5 (3), 178-184 (2006).</li><li>Redecker, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Glomalean+fungi+from+the+ordovician.">Glomalean fungi from the ordovician.</a> Science. 289 (5486), 1920-1921 (2000).</li><li>Olsson, P. A., Jakobsen, I., Wallander, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Foraging and Resource Allocation Strategies of Mycorrhizal Fungi in a Patchy Environment. Mycorrhizal Ecology. Ecological Studies. , (2003).</li><li>Zheng, C., Chai, M., Jiang, S., Zhang, S., Christie, P., Zhang, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Foraging+capability+of+extraradical+mycelium+of+arbuscular+mycorrhizal+fungi+to+soil+phosphorus+patches+and+evidence+of+carry-over+effect+on+new+host+plant.">Foraging capability of extraradical mycelium of arbuscular mycorrhizal fungi to soil phosphorus patches and evidence of carry-over effect on new host plant.</a> Plant Soil. 387 (1-2), 201-217 (2015).</li><li>Singh, A. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+role+of+glomalin+in+mitigation+of+multiple+soil+degradation+problems.">The role of glomalin in mitigation of multiple soil degradation problems.</a> Crit Rev Environ Sci Technol. 52 (9), 1604-1638 (2022).</li><li>Wilson, G. W. T., Rice, C. W., Rillig, M. C., Springer, A., Hartnett, D. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Soil+aggregation+and+carbon+sequestration+are+tightly+correlated+with+the+abundance+of+arbuscular+mycorrhizal+fungi:+results+from+long-term+field+experiments.">Soil aggregation and carbon sequestration are tightly correlated with the abundance of arbuscular mycorrhizal fungi: results from long-term field experiments.</a> Ecol Lett. 12 (5), 452-461 (2009).</li><li>Gianinazzi, S., Gollotte, A., Binet, M. -. N., van Tuinen, D., Redecker, D., Wipf, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Agroecology:+the+key+role+of+arbuscular+mycorrhizas+in+ecosystem+services.">Agroecology: the key role of arbuscular mycorrhizas in ecosystem services.</a> Mycorrhiza. 20 (8), 519-530 (2010).</li><li>St&#252;rmer, S. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+history+of+the+taxonomy+and+systematics+of+arbuscular+mycorrhizal+fungi+belonging+to+the+phylum+Glomeromycota.">A history of the taxonomy and systematics of arbuscular mycorrhizal fungi belonging to the phylum Glomeromycota.</a> Mycorrhiza. 22 (4), 247-258 (2012).</li><li>Gerdemann, J. W., Nicolson, T. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Spores+of+mycorrhizal+Endogone+species+extracted+from+soil+by+wet+sieving+and+decanting.">Spores of mycorrhizal Endogone species extracted from soil by wet sieving and decanting.</a> Trans Br Mycol Soc. 46 (2), 235-244 (1963).</li><li>Walker, C., Vestberg, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+simple+and+inexpensive+method+for+producing+and+maintaining+closed+pot+cultures+of+arbuscular+mycorrhizal+fungi.">A simple and inexpensive method for producing and maintaining closed pot cultures of arbuscular mycorrhizal fungi.</a> Agr Sci Finland. 3, 233-240 (1994).</li><li>Fortin, J. A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Arbuscular+mycorrhiza+on+root-organ+cultures.">Arbuscular mycorrhiza on root-organ cultures.</a> Can J Bot. 80 (1), 1-20 (2002).</li><li>Par&#233;, L., Banchini, C., Hamel, C., Bernier, L., Stefani, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+simple+and+low-cost+technique+to+initiate+single-spore+cultures+of+arbuscular+mycorrhizal+fungi+using+a+superabsorbent+polymer.">A simple and low-cost technique to initiate single-spore cultures of arbuscular mycorrhizal fungi using a superabsorbent polymer.</a> Symbiosis. 88, 61-73 (2022).</li><li>Saha, A., Sekharan, S., Manna, U. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Superabsorbent+hydrogel+(SAH)+as+a+soil+amendment+for+drought+management:+A+review.">Superabsorbent hydrogel (SAH) as a soil amendment for drought management: A review.</a> Soil Tillage Res. 204, 104736 (2020).</li><li>B&#233;card, G., Fortin, J. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Early+events+of+vesicular-arbuscular+mycorrhiza+formation+on+Ri+T-DNA+transformed+roots.">Early events of vesicular-arbuscular mycorrhiza formation on Ri T-DNA transformed roots.</a> New Phytol. 108 (2), 211-218 (1988).</li><li>Vierheilig, H., Coughlan, A. P., Wyss, U., Pich&#233;, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ink+and+vinegar,+a+simple+staining+technique+for+arbuscular-mycorrhizal+fungi.">Ink and vinegar, a simple staining technique for arbuscular-mycorrhizal fungi.</a> Appl Environ Microbiol. 64 (12), 5004-5007 (1998).</li></ol>

The authors have nothing to disclose.

Inoculation is the most critical step in the protocol, and the extruded glass Pasteur pipettes proved to be an excellent tool for accurately manipulating single spores of AM fungi while preserving their integrity. The extruded glass Pasteur pipettes are easily shaped using the flame of a candle or Bunsen burner, and the opening can be adjusted under the stereomicroscope to match the size of the spore being pipetted. It is important to manipulate the spores with tools adapted to the size of AM fungal spore (Supplementary Figure 1) and to inoculate the SAP-AS when the host plant roots are long enough to reach the Nitex membrane where the spore is deposited.
The SAP-AS are easy to adapt to the experiment requirements. Larger Petri dishes can be used, with multi-compartments, to monitor, for example, the interaction between closely relative strains or between different species of AMF or to modify the chemical (pH) or biological environment (introduction&#160;of nematodes, bacteria, fungi). Various mycotrophic host plants can also be used to provide the AM fungi with photosynthates. The nutrient solution mMS-1 was derived from the minimal (M) medium recipe described by B&#233;card and Fortin (1988)15 minus the sucrose, vitamins, and bacto agar to limit carbon sources. However, the SAP-AS can be supplemented with various nutrient solutions, depending on the experiment objectives.
The propagation of AM fungi in SAP-AS requires regular watering. The limited volume of vermiculite and SAP exposes the roots and the AM fungus to fluctuations in humidity, especially in standard two-compartment Petri dishes (10 cm diameter). The ability to expand and, therefore, the transparency of the SAP grains decreases over time. In fact, the presence of cations from the nutrient solution progressively limits the expansion of the acrylate network and requires the replacement of the SAP after months. In addition, green algae and mold may grow over time if Petri dishes are not properly protected from light or overwatered.
To date, seven AM fungal species have been successfully cultivated in SAP-AS, which is far below the number of AM fungal species that can be propagated in pot cultures. However, both the biotic and abiotic conditions in SAP-AS are very similar to those in pot cultures, and it is likely that other AM fungal species should be able to propagate in SAP-AS. Direct inoculation of spores in SAP-AS probably provides environmental conditions closer to those of the rhizosphere in a natural soil due to the presence of root exudates and/or bacteria, if non-sterile spores/seeds are used for inoculation. This should be preferred to inoculation with germinated spores. In addition, the conditions that trigger spore germination within AMF are still poorly understood, therefore SAP hydrated with mMS-1 nutrient solution may not be adapted to germinate spores of other AM fungal species. Spore germination on SAP hydrated with mMS-1 nutrient solution was tested to specifically select viable spores for the inoculation step using only R. irregularis inoculum.
Inoculation and monitoring of the development of the AM symbiosis are easily performed in SAP-AS. The modified two-compartment Petri dishes allow the cultivation of different AM fungal species. Par&#233; et al.12 have propagated seven different AMF species from six genera and three families. Modification of two-compartment Petri dishes is easily done with inexpensive tools. The cost and quantity of materials (vermiculite, SAP, Pasteur pipette, etc.) and reagents (mMS-1) required to prepare and maintain the SAP-AS are limited, allowing a large number of SAP-AS to be managed at minimal cost. The ability to stack the SAP-AS also significantly reduces the footprint of AM fungal cultures compared to pot cultures. For example, 50 SAP-AS (5 stacks of ten) can fit on a 1 m long shelf (Supplementary&#160;Figure 2). These features make the SAP-AS a simple and inexpensive technique that is compatible with teaching AM symbiosis in high school lab courses or at the undergraduate level in universities. Colonized grains of SAP can be used to inoculate new SAP-AS or pot cultures.
The presence of a coverslip at the back of the bottom of the Petri dish allows high-resolution photography and video of the extraradical fungal structures. The cytoplasmic flow can be easily studied under living conditions that are very close to natural conditions. This is of great importance for studies of AM fungi functions related to their mycelia (nutrients, water transport, soil structure, etc.) and for studies of hyphal morphogenesis.
AMF complete their biological cycle in plant roots and within the rhizosphere. The study of soil microorganisms is complex due to the inherent difficulty of observing the soil environment. The main objective of the SAP-AS is to recreate an environment as similar as possible to the rhizosphere for the propagation of AM fungi while maintaining the ability to observe the development of AM fungi in great detail. Because this implies non-sterile conditions, the amount of available carbon should be limited to avoid the proliferation of saprotrophic microorganisms. The knowledge of the behavior of AM fungi in the rhizosphere is still extremely limited, and the SAP-AS offers the possibility to make detailed comparisons between species regarding their ability to forage in the extraradical environment, their spore production, and their root colonization. This can be further complicated by adding interactions with other soil species such as bacteria, nematodes, protists, and root fungal pathogens, and the knowledge of soil microbiota interactions can be improved thanks to the SAP-AS.

Arbuscular mycorrhizal (AM) fungi (Glomeromycotina) are ancient plant root symbionts (~500 Ma1,2) that may have played an essential role in the colonization of terrestrial soils by tracheophytes. This long coevolution between AM fungi and tracheophytes places arbuscular mycorrhiza as a masterpiece of interkingdom mutualism. AM fungal hyphae significantly increase the ability of the host to forage for soil nutrients3, including nutrient carry-over to new hosts via mycorrhizal networks4. The hyphal network improves soil structure, and the production of glomalin could reduce soil erosion5. The transfer of part of the atmospheric carbon to the fungal root symbiont increases soil carbon sequestration6. Overall, AM fungi improve plant resilience to both abiotic and biotic stresses and have therefore, received considerable attention in agroecology7. Indeed, AM fungi-friendly agricultural management practices have the potential to reduce the use of chemical inputs for crop production and improve soil organic carbon content, which are important objectives that farmers need to integrate into their management practices in order to comply with national and international commitments regarding the transition to sustainable agricultural practices and the fight against climate change.
However, AM fungi are soil microscopic fungi, and their study is difficult due to their obligate biotrophy and rhizosphere distribution. Soil is one of the most difficult biotopes to study because of its opacity, the huge diversity of niches, and multi-trophic interactions at all scales. The isolation, propagation, and characterization of AM fungi are, therefore difficult. Until the middle of the 20th century, only AM fungal species forming sporocarps had been characterized8. However, the majority of AM fungal species produce non-sporocarpic spores ranging from ~20 &#956;m to ~500 &#956;m in diameter. The description of the soil wet sieving technique9 opened the way to describe these AM fungal species, and the rate of species description has increased since then. Nevertheless, AM fungi represent a small group of species compared to Dikarya.
Trap cultures, i.e., the inoculation with spores or an environmental soil sample containing AM fungal spores of a pot filled with autoclaved material such as turface&#160;and vermiculite and a sterilized seed of a host (leek, plantain), is one way to propagate AM fungi under controlled conditions10. However, the success of the inoculation can only be assessed by looking for the presence of arbuscules in root fragments after staining or by wet sieving a subsample or the entire pot to isolate spores. It is usually recommended not to disturb the system for at least 6-12 weeks before the analysis of the pot culture. This culture technique is suitable for propagating most known AM fungal species, but live observation of the fungal symbiont is not possible, and the success of inoculation is uncertain, especially when single spore cultures are attempted.
On the contrary, the in vitro propagation of AM fungi can be monitored live thanks to the transparency of the culture medium11, but this culture technique requires the availability of transformed roots and the presence of carbon in the culture medium to work in a sterile environment. The spores must be sterilized, and together with the association with a heterotrophic host, most of the known AM fungal species are not successfully propagated using this technique.
Therefore, the propagation of AM fungi using current techniques, although established and widely used in most laboratories, has some limitations for the study of AM fungi. Par&#233; et al. (2022)12 developed an in vivo technique using a transparent superabsorbent polymer (SAP) in combination with whole plants to propagate AM fungi. The technique, designed as an SAP-based autotrophic system (SAP-AS), is simple and inexpensive and combines the advantages of pot culture (association with an autotrophic host, non-sterile conditions) and in vitro cultures (transparent medium, live monitoring of symbiosis development). Here, we present a protocol explaining how to set up the cultures with single spore inoculation and use the SAP-AS for high-magnification observation of the extraradical mycelium. Specifically, we describe how to modify two-compartment Petri dishes, prepare the nutrient solution, prepare the superabsorbent polymer (SAP), prepare the seedlings, assemble the SAP-AS and inoculate with a single spore, pregerminate the spores, and live monitor the development of the symbiosis.

<table><tbody><tr><td>100 x 15 mm Stackable Bi-Plate</td><td>Kord Valmark</td><td>1204U09</td><td>https://www.thomassci.com/Laboratory-Supplies/Petri-Dishes/_/100-x-15-mm-Stackable-Bi-Plate</td></tr><tr><td>12-well plate&amp;nbsp;</td><td>Greiner Bio-one</td><td>665180</td><td>https://shop.gbo.com/en/row/products/bioscience/cell-culture-products/cellstar-cell-culture-multiwell-plates/665180.html</td></tr><tr><td>18 mm round glass coverslips</td><td>Fisher Scientific</td><td>12-545-100</td><td>https://www.fishersci.com/shop/products/fisherbrand-cover-glasses-circles-11/12545100#?keyword=12-545-100</td></tr><tr><td>20 mL Syringe PP/PE without needle</td><td>Millipore Sigma</td><td>Z683620-100EA</td><td>https://www.sigmaaldrich.com/CA/en/product/aldrich/z683620?utm_source=google&amp;amp;utm_medium=&lt;br/&gt; cpc&amp;amp;utm_campaign=20674735406&lt;br/&gt; &amp;amp;utm_content=157607444391&amp;amp;gc&lt;br/&gt; lid=Cj0KCQiA5rGuBhCnARIsAN11&lt;br/&gt; vgQOT_WPRg9WFyBEyoO4b0x1&lt;br/&gt; -F7Tks4houU7VTRS5EiYM9l0F-B&lt;br/&gt; oL7saAmFoEALw_wcB</td></tr><tr><td>Acupuncture needle&amp;nbsp;</td><td>Lierre</td><td>A143-LP1-3075</td><td>https://www.lierre.ca/products/lierre-plus-acupuncture-needles-100pcs?gad&lt;br/&gt; _source=1&amp;amp;gclid=Cj0KCQiA5rGuBh&lt;br/&gt; CnARIsAN11vgTwupmw51UTdR&lt;br/&gt; k9cKr4ewi12W3dyVikenzH3sjdUB4&lt;br/&gt; g41G-_KnvppoaAkbTEALw_wcB&amp;amp;&lt;br/&gt; utm_campaign=PMax-needles&amp;amp;utm_content=shopify_CA_&lt;br/&gt; 5213169090694_35001500991622&lt;br/&gt; &amp;amp;utm_medium=cpc&amp;amp;utm_source=&lt;br/&gt; google&amp;amp;variant=35001500991622</td></tr><tr><td>Blotting paper</td><td>FLINN&amp;nbsp;</td><td>FB0678</td><td>https://www.flinnsci.ca/blotting-paper-12-x-19-pkg.-of-10/fb0678/</td></tr><tr><td>Commercial or scientific blender or kitchen hand blender</td><td>kitchenaid</td><td>KHBV53DG</td><td>https://www.kitchenaid.ca/en_ca/countertop-appliances/hand-blenders/hand-blender-products/p.variable-speed-corded-hand-blender.khbv53dg.html&amp;nbsp;</td></tr><tr><td>Dremel 199 Carving Bit</td><td>Dremel</td><td>2615000199</td><td>https://www.dremel.com/ca/en/p/199-2615000199</td></tr><tr><td>Dry SAP medium granulometry 1&amp;ndash;2 mm</td><td>HORTA-SORB MD</td><td>00810085242789</td><td>https://www.horticulturalalliance.com/product/horta-sorb-md-granule/</td></tr><tr><td>Feather Stainless-Steel Blades for Dissecting Knife Handles&amp;nbsp;</td><td>Fisher Scientific</td><td>08-916-5B</td><td>https://www.fishersci.ca/shop/products/graham-field-stainless-steel-blades-dissecting-knife-handles-8/089165b</td></tr><tr><td>Glass Pasteur pipettes 230 mm</td><td>Kimble</td><td>RK-25554-14</td><td>https://www.coleparmer.ca/i/dwk-life-sciences-kimble-disposable-pasteur-pipettes-plugged-end-borosilicate-glass-230-mm-1000-cs/2555414</td></tr><tr><td>Ink</td><td>Sheaffer</td><td>94321</td><td>https://www.amazon.com/Sheaffer-Skrip-Bottled-Black-94231/dp/B002IKKKUU</td></tr><tr><td>Melting guide: modified paint Scraper, 2-in</td><td>Mastercraft</td><td>#049-7335-8</td><td>https://www.canadiantire.ca/en/pdp/mastercraft-carbon-steel-flexible-spackling-putty-knife-wall-paint-scraper-2-in-0497335p.0497335.html?loc=plp</td></tr><tr><td>Microscopy glass slide</td><td>Fisher Scientific</td><td>12-552-5</td><td>https://www.fishersci.com/shop/products/fisherbrand-frosted-microscope-slides-4/125525</td></tr><tr><td>Nitex nylon mesh filter screen&amp;nbsp;</td><td>Dynamic Aqua-Supply Ltd.</td><td>NTX30-108</td><td>https://dynamicaquasupply.com/products/nitex-screen?_pos=1&amp;amp;_sid=ffc105328&amp;amp;_ss=r&amp;amp;&lt;br/&gt; variant=6945749106731</td></tr><tr><td>Paper clip</td><td>Makanu</td><td>&amp;lrm;Clips-BK-41mm-24</td><td>https://www.amazon.ca/classeur-standard-grandes-trombones-excellentes</td></tr><tr><td>Parafilm</td><td>Avantor/vwr</td><td>470201-930</td><td>https://www.avantorsciences.com/ca/en/product/8882964/parafilm</td></tr><tr><td>Plantago lanceolata seeds</td><td>ecoumene</td><td>NA</td><td>https://www.ecoumene.com/produit/semences/herbacees/plantain-lanceole-bio/</td></tr><tr><td>Polyvinyl alcohol-lactic acid-glycerol (PVLG).</td><td>NA</td><td>NA</td><td>https://invam.ku.edu/recipes</td></tr><tr><td>Pyrography kit with fine tip</td><td>Walnut Hollow</td><td>483103</td><td>https://www.walnuthollow.com/collections/creative-wood-burning/products/walnut-hollow-creative-versa-tool</td></tr><tr><td>Silicone sealant</td><td>Aqueon</td><td>100165003</td><td>https://www.aqueon.com/products/aquariums/silicone-sealant</td></tr><tr><td>Surgeon scalpel handle</td><td>Fisher Scientific</td><td>22-079657</td><td>https://www.fishersci.ca/shop/products/surgical-design-scalpel-handles-blades/22079657#?keyword=scalpel</td></tr><tr><td>Two Speed Rotary Tool Kit</td><td>Dremel</td><td>200-1/21</td><td>https://www.dremel.com/ca/en/p/200-1-21-f0130200ah</td></tr><tr><td>Vermiculite</td><td>PRO-MIX</td><td>4981110</td><td>https://www.canadiantire.ca/fr/pdp/vermiculite-pro-mix-9-l-0597936p.0597936.html</td></tr><tr><td>X1000 Round Coverslip dia. 30 mm #1 (0.13&amp;ndash;0.16 mm)</td><td>Fisher Scientific</td><td>12164692</td><td>https://www.fishersci.fi/shop/products/x1000-cover-slip-diam-30-mm-n-1-1/12164692</td></tr></tbody></table>

inoculating and observing arbuscular mycorrhizal cultures on superabsorbent polymer-based autotrophic systems

Arbuscular mycorrhizal (AM) fungi are difficult to manipulate and observe due to their permanent association with plant roots and propagation in the rhizosphere. Typically, AM fungi are cultured under in vivo conditions in pot culture with an autotrophic host or under in vitro conditions with Ri Transfer-DNA transformed roots (heterotrophic host) in a Petri dish. Additionally, the cultivation of AM fungi in pot culture occurs in an opaque and non-sterile environment. In contrast, in vitro culture involves the propagation of AM fungi in a sterile, transparent environment. The superabsorbent polymer-based autotrophic system (SAP-AS) has recently been developed and shown to combine the advantages of both methods while avoiding their respective limitations (opacity and heterotrophic host, sterility). Here, we present a detailed protocol for easy preparation, single spore inoculation, and observation of AM fungi in SAP-AS. By modifying the Petri dishes, high-resolution photographic and video observations were possible on living specimens, which would have been difficult or impossible with current in vivo and in vitro techniques.

The SAP-AS is a simple and inexpensive technique for culturing AM fungi and observing the development of intraradical and extraradical fungal structures. Here, we provided a detailed protocol to help users set up SAP-AS and we introduced two modifications compared to the original description of the SAP-AS.
First, the presence of SAP on the root compartment along the Nitex membrane facilitates the inoculation of the system with a single spore (Figure 1).
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/66848/66484fig01.jpg" /> 
Figure 1: Single spore inoculation of the SAP-AS. (A) Inoculation with a single spore of Rhizophagus irregularis. (B) Inoculation with a single spore of Funneliformis mosseae. The white arrows indicate the point of inoculation. Scale bars: 500 &#181;m. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/66848/66484fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
It is easy to identify an area with a few roots where the spore can be deposited. The exact location of the spore can be marked on the surface of the Petri dish lid and checked periodically for germination and colonization of the roots. The presence of hydrated grains of SAP provides a moist environment conducive to spore germination. The inoculation on the roots next to the Nitex membrane allows rapid development of the symbiosis with the extraradical mycelium to quickly access the hyphal compartment and forage for nutrients (Figure 2). The ability to observe whether the single spore placed at the inoculation point germinates or not also allows us to identify and remove unsuccessful cultures and replace them.
Second, the coverslips at the bottom of the Petri dish allow high-resolution live imaging of the AM-fungal symbiosis (Figure 2B,C) and, in particular, of the cytoplasmic flow within the extraradical mycelium (Figure 2D).
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/66848/66484fig02.jpg" /> 
Figure 2: Inoculated SAP-AS. (A) SAP-AS inoculated with a single spore of Rhizophagus irregularis (DAOM 197198). The host plant is Plantago lanceolata. (B) Cluster of spores observed through the coverslip in the hyphal compartment under a stereomicroscope. Scale bar: 500 &#181;m. (C) High-resolution photograph of the spore cluster observed through the coverslip under a light microscope at 10x magnification. Scale bar: 100 &#181;m (D) High-resolution photograph of hyphae observed through the coverslip under a light microscope at 100x magnification. Scale bar: 10 &#181;m. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/66848/66484fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Users can attempt to germinate AM fungal spores on SAP hydrated with mMS-1 nutrient solution to guarantee the SAP-AS are inoculated only with viable spores (Figure 3). However, this was tested only with commercial spores of R. irregularis, and the success of spore germination on SAP hydrated with mMS-1 nutrient solution may vary significantly with other AM fungal species.
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/66848/66484fig03.jpg" /> 
Figure 3: Germination of R. irregularis spores in 12-well plate. Scale bar: 500 &#181;m. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/66848/66484fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Finally, because SAP-AS is an in vivo, non-sterile technique for propagating AMF, the Petri dish can be manipulated on the bench and opened to sample colonized roots, free spores, or colonized grains of SAP (Figure 4). Intraradical and extraradical fungal structures can be stained in a manner similar to AMF propagated in pot or root organ cultures (Figure 4C).
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/66848/66484fig04.jpg" /> 
Figure 4: Extraradical and intraradical AM fungal structures extracted from the SAP-AS. (A) Free spores of R. irregularis observed in the root compartment. Scale bar: 200 &#181;m. (B) Spores of R. irregularis stained in SAP. Scale bar: 500 &#181;m. (C) Stained root fragments showing the intraradical hyphae and arbuscules. Scale bars: 50 &#181;m, 100 &#181;m. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/66848/66484fig04large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
Supplementary Figure 1: Comparison of the thickness of the various tools available to manipulate AM fungal spores. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/66848/Supplementary Figure 1.zip" target="_blank">Please click here to download this File.</a>
Supplementary Figure 2: Stacked SAP-AS. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/66848/Supplementary Figure 2.zip" target="_blank">Please click here to download this File.</a>

Author Spotlight: Enhancing AM Fungi Research with SAP-AS &#8212; A Novel Technique for Single-Spore Cultures

Here, we describe a simple and inexpensive technique for inoculating and observing arbuscular mycorrhizal fungi in superabsorbent polymer-based autotrophic systems.

Inoculating and Observing Arbuscular Mycorrhizal Cultures on Superabsorbent Polymer-Based Autotrophic Systems

Arbuscular mycorrhizal (AM) fungi are difficult to manipulate and observe due to their permanent association with plant roots and propagation in the ...

inoculating-observing-arbuscular-mycorrhizal-cultures-on

Nanyang Technological University

Research

JoVE Journal

Environment

1.5K Views.  Université Laval. Kortom, alle schimmels zijn oude en essentiële symbionten van plantaardig voedsel, en ze verbeteren de opname van voedingsstoffen door de gastheer en zijn ook belangrijke spelers in de gezondheid van cellen. Hoewel celmicro-organismen moeilijk te bestuderen zijn, maakt ons protocol real-time monitoring, digitale observatie en efficiënte oprichting van enkelspaakculturen mogelijk. Momenteel worden AM-schimmels vermeerderd in potcultuur, in kasomstandigheden ...

Video: Auteur in de schijnwerpers: onderzoek naar AM-schimmels verbeteren met SAP-AS - een nieuwe techniek voor culturen met één spore

A Whole Cell Bioreporter Approach to Assess Transport and Bioavailability of Organic Contaminants in Water Unsaturated Systems

Bioavailability of contaminants is a prerequisite for their effective biodegradation in soil. The average bulk concentration of a contaminant, however, is not an appropriate measure for its availability; bioavailability rather depends on the dynamic interplay of potential mass transfer (flux) of a compound to a microbial cell and the capacity of the latter to degrade the compound. In water-unsaturated parts of the soil, mycelia have been shown to overcome bioavailability limitations by actively transporting and mobilizing organic compounds over the range of centimeters. Whereas the extent of mycelia-based transport can be quantified easily by chemical means, verification of the contaminant-bioavailability to bacterial cells requires a biological method. Addressing this constraint, we chose the PAH fluorene (FLU) as a model compound and developed a water unsaturated model microcosm linking a spatially separated FLU point source and the FLU degrading bioreporter bacterium Burkholderia sartisoli RP037-mChe by a mycelial network of Pythium ultimum. Since the bioreporter expresses eGFP in response of the PAH flux to the cell, bacterial FLU exposure and degradation could be monitored directly in the microcosms via confocal laser scanning microscopy (CLSM). CLSM and image analyses revealed a significant increase of the eGFP expression in the presence of P. ultimum compared to controls without mycelia or FLU thus indicating FLU bioavailability to bacteria after mycelia-mediated transport. CLSM results were supported by chemical analyses in identical microcosms. The developed microcosm proved suitable to investigate contaminant bioavailability and to concomitantly visualize the involved bacteria-mycelial interactions.

A whole cell bioreporter assay with Burkholderia sartisoli RP037-mChe was developed to detect fractions of an organic contaminant (i.e., fluorene) available for bacterial degradation after active transport by mycelia bridging air-filled pores in a water unsaturated model system.

Bioavailability of contaminants is a prerequisite for their effective biodegradation in soil. The average bulk concentration of a contaminant, however, is ...

A New Application of the Electrical Penetration Graph (EPG) for Acquiring and Measuring Electrical Signals in Phloem Sieve Elements

Electrophysiological properties of cells are often studied in vitro, after dissociating them from their native environments. However, the study of electrical transmission between distant cells in an organism requires in vivo, artifact-free recordings of cells embedded within their native environment. The transmission of electrical signals from wounded to unwounded areas in a plant has since long piqued the interest of botanists. The phloem, the living part of the plant vasculature that is spread throughout the plant, has been postulated as a major tissue in electrical transmission in plants. The lack of suitable electrophysiological methods poses many challenges for the study of the electrical properties of the phloem cells in vivo. Here we present a novel approach for intracellular electrophysiology of sieve elements (SEs) that uses living aphids, or other phloem-feeding hemipteran insects, integrated in the electrical penetration graph (EPG) circuit. The versatility, robustness, and accuracy of this method made it possible to record and study in detail the wound-induced electrical signals in SEs of central veins of the model plant Arabidopsis thaliana1. Here we show that EPG-electrodes can be easily implemented for intracellular electrophysiological recordings of SEs in marginal veins, as well as to study the capacity of SEs to respond with electrical signals to several external stimuli. The EPG approach applied to intracellular electrophysiology of SEs can be implemented to a wide variety of plant species, in a large number of plant/insect combinations, and for many research aims.

A New Application of the Electrical Penetration Graph EPG for Acquiring and Measuring Electrical Signals in Phloem Sieve Elements

Electrical Penetration Graph (EPG) is a well-established technique for studying the feeding behavior of stylet-bearing insects. Here we show a new application of EPG as a non-invasive tool for the acquisition of intracellular electrophysiology recordings of sieve elements (SEs), the cells that form the phloem vasculature in plants.

Electrophysiological properties of cells are often studied in vitro, after dissociating them from their native environments. However, the study of ...

Customization of Aspergillus niger Morphology Through Addition of Talc Micro Particles

The filamentous fungus A. niger is a widely used strain in a broad range of industrial processes from food to pharmaceutical industry. One of the most intriguing and often uncontrollable characteristics of this filamentous organism is its complex morphology. It ranges from dense spherical pellets to viscous mycelia (Figure 1). Various process parameters and ingredients are known to influence fungal morphology 1. Since optimal productivity correlates strongly with a specific morphological form, the fungal morphology often represents the bottleneck of productivity in industrial production.
A straight forward and elegant approach to precisely control morphological shape is the addition of inorganic insoluble micro particles (like hydrous magnesium silicate, aluminum oxide or titanium silicate oxide) to the culture medium contributing to increased enzyme production 2-6. Since there is an obvious correlation between micro particle dependent morphology and enzyme production it is desirable to mathematically link productivity and morphological appearance. Therefore a quantitative precise and holistic morphological description is targeted.
Thus, we present a method to generate and characterize micro particle dependent morphological structures and to correlate fungal morphology with productivity (Figure 1) which possibly contributes to a better understanding of the morphogenesis of filamentous microorganisms.
The recombinant strain A. niger SKAn1015 is cultivated for 72 h in a 3 L stirred tank bioreactor. By addition of talc micro particles in concentrations of 1 g/L, 3 g/L and 10 g/L prior to inoculation a variety of morphological structures is reproducibly generated. Sterile samples are taken after 24, 48 and 72 hours for determination of growth progress and activity of the produced enzyme. The formed product is the high-value enzyme &beta;-fructofuranosidase, an important biocatalyst for neo-sugar formation in food or pharmaceutical industry, which catalyzes among others the reaction of sucrose to glucose 7-9. Therefore, the quantification of glucose after adding sucrose implies the amount of produced &beta;-fructofuranosidase. Glucose quantification is made by a GOD/POD-Assay 10, which is modified for high-throughput analysis in 96-well micro titer plates.
Fungal morphology after 72 hours is examined by microscope and characterized by digital image analysis. In doing so, particle shape factors for fungal macro morphology like Feret's diameter, projected area, perimeter, circularity, aspect ratio, roundness und solidity are calculated with the open source image processing program ImageJ. Relevant parameters are combined to a dimensionless Morphology number (Mn) 11, which enables a comprehensive characterization of fungal morphology. The close correlation of the Morphology number and productivity are highlighted by mathematical regression.

Customization of Aspergillus niger Morphology Through Addition of Talc Micro Particles

A method to precisely generate and to comprehensively characterize morphology of filamentous fungus Aspergillus niger is described, which allows the mathematical correlation of morphological appearance and productivity.

The filamentous fungus A. niger is a widely used strain in a broad range of industrial processes from food to pharmaceutical industry. One of the most ...

Immunology and Infection

Investigation of Plant Interactions Across Common Mycorrhizal Networks Using Rotated Cores

Arbuscular mycorrhizal (AM) fungi influence plant mineral nutrient uptake and growth, hence, they have the potential to influence plant interactions. The power of their influence is in extraradical mycelia that spread beyond nutrient depletion zones found near roots to ultimately interconnect individuals within a common mycorrhizal network (CMN). Most experiments, however, have investigated the role of AM fungi in plant interactions by growing plants with versus without mycorrhizal fungi, a method that fails to explicitly address the role of CMNs. Here, we propose a method that manipulates CMNs to investigate their role in plant interactions. Our method uses modified containers with conical bottoms with a nylon mesh and/or hydrophobic material covering slotted openings, 15N fertilizer, and a nutrient-poor interstitial sand. CMNs are left either intact between interacting individuals, severed by rotation of containers, or prevented from forming by a solid barrier. Our findings suggest that rotating containers is sufficient to disrupt CMNs and prevent their effects on plant interactions across CMNs. Our approach is advantageous because it mimics aspects of nature, such as seedlings tapping into already established CMNs and the use of a suite of AM fungi that may provide diverse benefits. Although our experiment is limited to investigating plants at the seedling stage, plant interactions across CMNs can be detected using our approach which therefore can be applied to investigate biological questions about the functioning of CMNs in ecosystems.

Most plants within communities likely are interconnected by arbuscular mycorrhizal (AM) fungi, but mediation of plant interactions by them has been investigated primarily by growing plants with versus without mycorrhizas. We present a method to manipulate common mycorrhizal networks among mycorrhizal plants to investigate their consequences for plant interactions.

Arbuscular mycorrhizal (AM) fungi influence plant mineral nutrient uptake and growth, hence, they have the potential to influence plant interactions. The ...

Inoculation Strategies to Infect Plant Roots with Soil-Borne Microorganisms

The rhizosphere harbors a highly complex microbial community in which plant roots are constantly challenged. Roots are in close contact with a wide variety of microorganisms, but studies on soil-borne interactions are still behind those performed on aboveground organs. Although some inoculation strategies for infecting model plants with model root pathogens are described in the literature, it remains difficult to get a comprehensive methodological overview. To address this problem, three different root inoculation systems are precisely described that can be applied to gain insights into the biology of root-microbe interactions. For illustration, Verticillium species (namely, V. longisporum and V. dahliae) were employed as root invading model pathogens. However, the methods can be easily adapted to other root colonizing microbes - both pathogenic and beneficial. By colonizing the plant xylem, vascular soil-borne fungi such as Verticillium spp. exhibit a unique lifestyle. After root invasion, they spread via the xylem vessels acropetally, reach the shoot, and elicit disease symptoms. Three representative plant species were chosen as model hosts: Arabidopsis thaliana, economically important oilseed rape (Brassica napus), and tomato (Solanum lycopersicum). Step-by-step protocols are given. Representative results of pathogenicity assays, transcriptional analyses of marker genes, and independent confirmations by reporter constructs are shown. Furthermore, the advantages and disadvantages of each inoculation system are thoroughly discussed. These proven protocols can assist in providing approaches for research questions on root-microbe interactions. Knowing how plants cope with microbes in the soil is crucial for developing new strategies to improve agriculture.

This protocol presents a detailed summary of strategies to inoculate plant roots with soil-borne microbes. Exemplified for the fungi Verticillium longisporum and Verticillium dahliae, three different root infection systems are described. Potential applications and possible downstream analyses are highlighted, and advantages or disadvantages are discussed for each system.

The rhizosphere harbors a highly complex microbial community in which plant roots are constantly challenged. Roots are in close contact with a wide ...

Monitoring Bacterial Colonization and Maintenance on Arabidopsis thaliana Roots in a Floating Hydroponic System

Bacteria form complex rhizosphere microbiomes shaped by interacting microbes, larger organisms, and the abiotic environment. Under laboratory conditions, rhizosphere colonization by plant growth-promoting bacteria (PGPB) can increase the health or the development of host plants relative to uncolonized plants. However, in field settings, bacterial treatments with PGPB often do not provide substantial benefits to crops. One explanation is that this may be due to loss of the PGPB during interactions with endogenous soil microbes over the lifespan of the plant. This possibility has been difficult to confirm, since most studies focus on the initial colonization rather than maintenance of PGPB within rhizosphere communities. It is hypothesized here that the assembly, coexistence, and maintenance of bacterial communities are shaped by deterministic features of the rhizosphere microenvironment, and that these interactions may impact PGPB survival in native settings. To study these behaviors, a hydroponic plant-growth assay is optimized using Arabidopsis thaliana to quantify and visualize the spatial distribution of bacteria during initial colonization of plant roots and after transfer to different growth environments. This system&#8217;s reproducibility and utility are then validated with the well-studied PGPB Pseudomonas simiae. To investigate how the presence of multiple bacterial species may affect colonization and maintenance dynamics on the plant root, a model community from three bacterial strains (an Arthrobacter, Curtobacterium, and Microbacterium species) originally isolated from the A. thaliana rhizosphere is constructed. It is shown that the presence of these diverse bacterial species can be measured using this hydroponic plant-maintanence assay, which provides an alternative to sequencing-based bacterial community studies. Future studies using this system may improve the understanding of bacterial behavior in multispecies plant microbiomes over time and in changing environmental conditions.

Monitoring Bacterial Colonization and Maintenance on Arabidopsis thaliana Roots in a Floating Hydroponic System

Here we describe a hydroponic plant growth assay to quantify species presence and visualize the spatial distribution of bacteria during initial colonization of plant roots and after their transfer into different growth environments.

Bacteria form complex rhizosphere microbiomes shaped by interacting microbes, larger organisms, and the abiotic environment. Under laboratory conditions, ...

A Hydroponic Co-cultivation System for Simultaneous and Systematic Analysis of Plant/Microbe Molecular Interactions and Signaling

An experimental design mimicking natural plant-microbe interactions is very important to delineate the complex plant-microbe signaling processes. Arabidopsis thaliana-Agrobacterium tumefaciens provides an excellent model system to study bacterial pathogenesis and plant interactions. Previous studies of plant-Agrobacterium interactions have largely relied on plant cell suspension cultures, the artificial wounding of plants, or the artificial induction of microbial virulence factors or plant defenses by synthetic chemicals. However, these methods are distinct from the natural signaling in planta, where plants and microbes recognize and respond in spatial and temporal manners. This work presents a hydroponic cocultivation system where intact plants are supported by metal mesh screens and cocultivated with Agrobacterium. In this cocultivation system, no synthetic phytohormone or chemical that induces microbial virulence or plant defense is supplemented. The hydroponic cocultivation system closely resembles natural plant-microbe interactions and signaling homeostasis in planta. Plant roots can be separated from the medium containing Agrobacterium, and the signaling and responses of both the plant hosts and the interacting microbes can be investigated simultaneously and systematically. At any given timepoint/interval, plant tissues or bacteria can be harvested separately for various &#34;omics&#34; analyses, demonstrating the power and efficacy of this system. The hydroponic cocultivation system can be easily adapted to study: 1) the reciprocal signaling of diverse plant-microbe systems, 2) signaling between a plant host and multiple microbial species (i.e.&#160;microbial consortia or microbiomes), 3) how nutrients and chemicals are implicated in plant-microbe signaling, and 4) how microbes interact with plant hosts and contribute to plant tolerance to biotic or abiotic stresses.

The described hydroponic cocultivation system supports intact plants with metal mesh screens and cocultivates them with bacteria. Plant tissue, bacteria, and secreted molecules can then be separately harvested for downstream analyses, simultaneously allowing for the molecular responses of both plant hosts and interacting microbes or microbiomes to be investigated.

An experimental design mimicking natural plant-microbe interactions is very important to delineate the complex plant-microbe signaling processes. ...

Biology

Mycorrhizal Maps as a Tool to Explore Colonization Patterns and Fungal Strategies in the Roots of Festuca rubra and Zea mays

Arbuscular mycorrhizal fungi are symbionts in the roots of plants. Their role is to sustain host development and maintain the nutritional equilibrium in the ecosystems. The colonization process is dependent on several factors like soil ecology, the genetic diversity of the fungi and host, and agronomic practices. Their synchronized action leads to the development of a complex hyphal network and leads to the secondary development of vesicles and arbuscules in the root cells. The aim of this research was to analyze the efficiency of the mycorrhizal patterns (MycoPatt) method for the positioning of fungal structures in the roots of Festuca rubra and Zea mays. Another objective was to explore the fungal colonization strategy as revealed by mycorrhizal maps of each species. The acquisition and assemblage of multiple microscopic images allow mycorrhizal colonization assessment in both corn and red fescue plants to provide information on the realistic position of the developed structures. The observed mycorrhizal patterns highlight the variable efficiency of each plant in terms of developing connections with soil symbiotic fungi, caused by applied treatments and growth stage. Mycorrhizal detailed maps obtained through the MycoPatt method are useful for the early detection of plant efficiency in symbiotic acquisition from the soil.

Mycorrhizal Maps as a Tool to Explore Colonization Patterns and Fungal Strategies in the Roots of Festuca rubra and Zea mays

The protocol here describes the methods for the assessment of the arbuscular mycorrhizal colonization patterns and strategy in roots for two species: Zea mays and Festuca rubra. The use of the MycoPatt method permits the calculation of parameters, the conversion of mycorrhizal structures into digital data, and the mapping of their real position in roots.

Arbuscular mycorrhizal fungi are symbionts in the roots of plants. Their role is to sustain host development and maintain the nutritional equilibrium in ...

Quantification of Arbuscular Mycorrhizal Fungi Colonization Rate in the Study of Invasive Alien Plants

Arbuscular mycorrhizal fungi (AMF) are widely distributed soil fungi in ecosystems and can form symbiotic associations (mycorrhizae) with the roots of most terrestrial plants. Plants provide carbon sources to AMF through mycorrhizal associations, while AMF hyphae can expand the range of nutrient absorption by roots and promote plant nutrient uptake. There are many different species of AMF, and the symbiotic relationships between different species of AMF and different plants vary. Invasive plants can enrich AMF species with better symbiotic capabilities through root exudates, promoting their growth and thereby increasing their colonization in invasive plant roots. At the same time, invasive plants can also disrupt the symbiotic relationship between AMF and native plants, affecting the local plant community, which is one of the mechanisms for successful plant invasion. The colonization rate of AMF in the roots of invasive and native plants indirectly reflects the role of AMF in the process of invasive plant invasion. In this method, collected plant roots can be processed directly or saved in a fixative for later batch processing. Through decolorization, acidification, staining, and destaining treatment of roots, the hyphae, spores, and arbuscular structures of AMF in the root system can be clearly observed. This method can be completed in a basic laboratory to observe and calculate the colonization rate of AMF in the root systems of invasive plants.

This protocol provides a simple and easy-to-use approach for determining the colonization rate of Arbuscular mycorrhizal fungi (AMF) in the roots of invasive plants.

Arbuscular mycorrhizal fungi (AMF) are widely distributed soil fungi in ecosystems and can form symbiotic associations (mycorrhizae) with the roots of ...

Production of Arbuscular Mycorrhizal (AM) Fungal Inoculum and Phenotypic Evaluation of Rice and AM Symbiosis Under Saline Conditions

Rice (Oryza sativa L.) is a vital food crop for more than half of the global population. However, its growth is severely impacted by saline soils, which present a significant challenge to crop production worldwide. Arbuscular mycorrhizal (AM) fungi, which form mutualistic symbiotic relationships with over 90% of agricultural plants and 80% of terrestrial plant species, have been shown to enhance the salt tolerance of rice plants. AM fungi are obligate symbionts that cannot complete their life cycle without a host root. Therefore, effectively utilizing plants to produce AM fungal inoculum is crucial for advancing research in this field. In this study, we present a series of robust methods that begin with generating sand inoculum containing spores of Rhizophagus irregularis using Allium tuberosum L. These methods include inoculating rice seedlings with the sand inoculum, analyzing the growth phenotype of mycorrhizal rice, and quantifying fungal colonization levels using trypan blue staining under salt stress. These approaches can efficiently generate AM fungal inoculum for further investigation into how AM symbiosis enhances the salinity tolerance of rice.

This article describes a protocol for generating arbuscular mycorrhizal (AM) fungi inoculum to investigate AM-enhanced salt stress tolerance in rice.

Rice (Oryza sativa L.) is a vital food crop for more than half of the global population. However, its growth is severely impacted by saline soils, which ...

Inoculating and Observing Arbuscular Mycorrhizal Cultures on Superabsorbent Polymer-Based Autotrophic Systems

Samenvatting

Meer video's verkennen

Hoofdstukken in deze video