Authors
Contact Us

Sign In

Thyristor Rectifier

Overview

Source: Ali Bazzi, Department of Electrical Engineering, University of Connecticut, Storrs, CT.

Similar to diodes, thyristors, also called silicon controlled rectifiers (SCRs), pass current in one direction from the anode to cathode, and block current flow in the other direction. However, current passage can be controlled through a "gate" terminal, which requires a small current pulse to turn on the thyristor so it can start conducting.

Thyristors are four-layer devices, composed of alternating layers of n-type and p-type material, thereby forming PNPN structures with three junctions. The thyristor has three terminals; with the anode connected to the p-type material of the PNPN structure, the cathode connected to the n-type layer, and the gate connected to the p-type layer nearest the cathode.

The objective of this experiment is to study a controlled thyristor-based half-wave rectifier at different conditions, and understand how different timings of the gate pulse affect the DC output voltage.

Principles

The thyristor only conducts under the same conditions as a diode, in addition to the condition of having a gate pulse to trigger the conduction process. For example, if an AC source is connected in series with a thyristor and a resistive load, the positive half-cycle of the source is not enough to forward bias the thyristor; the thyristor will remain reverse biased or off until a gate pulse is applied. It will then start conducting during that half-cycle. Thus, the thyristor has three terminals, the anode (A), cathode (K), and gate (G). Gate pulses are generated by "gate drive" circuits that drive current into the gate. The delay between the AC source zero crossing the gate pulse command is termed the "firing angle" which is an electrical angle.

Fig.1 shows a simple half-wave thyristor rectifier circuit with a pulse generating circuit (R1, R2, D1, D2, and C) that generates current pulses at the thyristor's gate. When the pulse is available and is "fired" at a firing angle which is a certain delay period from the zero crossing of the input voltage Vin, the thyristor acts like a diode in terms of passing current in one direction. Once the current goes to zero and the gate pulse is not available, the thyristor will remain off until the current is positive again and a gate pulse is fired.

In this experiment, we will study a controlled thyristor-based half-wave rectifier at different firing angles. The average output voltages for different angles are compared to study the effect of controlling the turn-on time on the average DC output voltage.

Figure 1
Figure 1: Half-wave rectifier with SCR and resistive load.

Procedure

ATTENTION: During this experiment, do not touch any part of the circuit while energized. Do NOT ground the VARIAC.

For this experiment, the variable transformer (VARIAC) at a low frequency of 60 Hz and peak of 35 V is used as the main AC source.

1. Setup

  1. Before starting, connect the differential probe to one scope channel.
    1. Set the button on the differential probe to 1/20 (or 20X) attenuation.
  2. On the scope channel menu, set the probe to be at 10X unless 20X is available for the differential probe. If 10X is chosen, manually multiply any measurements or results by two to reach the 20X desired.
  3. To setup the VARIAC, make sure the VARIAC output (looks like a regular receptacle) is not connected to any cable.
    1. Keep the VARIAC OFF and make sure its knob is set to zero.
    2. Slowly adjust the VARIAC knob to around 15% output.
  4. Before connecting the differential probe to the circuit, tie the probe's terminals together and adjust its measured waveform on the screen to show zero offset voltage.
  5. Connect the output cable to the VARIAC, and the differential voltage probe across the VARIAC output banana plugs.
    1. Turn the VARIAC ON.
    2. Slightly adjust the VARIAC to achieve 35V peak.
  6. Take a copy of Vin to use for reference. Show two to five fundamental cycles.
  7. Turn the VARIAC OFF. Do not adjust its knob setting for the rest of the experiment.

2. Half-Wave Rectifier SCR Circuit with Resistive Load and Zero Firing Angle

  1. The main rectifier component is the SCR (S), which is a TYN058. The load resistor (R) is 51 Ω. The SCR control circuit is enclosed in the dotted box of Fig. 1.
  2. The control circuit uses diodes (1N4004), a 1 kΩ resistor (R1), a control resistor that is manually changed (R2), and a ceramic (no polarity) 1 µF capacitor (C).
    1. Make sure the SCR and diode polarities are correct. The dash on the diode is at the cathode while the SCR pin assignment is shown in Fig. 2.
  3. On the proto board, build the circuit shown in Fig. 1. Use a short circuit instead of R2.
  4. Connect the differential voltage probe across the load resistor to observe the output voltage, Vout.
  5. Turn the VARIAC ON.
  6. Adjust the time base on the scope to show Vout for the same number of fundamental cycles that were captured for Vin. Make a copy of the waveforms.
    1. Measure the average or mean Vout.
    2. Zoom in between the SCR turn-off point and the next SCR turn-on point. Measure the time difference using the scope cursors. Make a copy of the waveform.
  7. Keep the differential probe connection and other circuit connections the same for the next part.
  8. Turn OFF the VARIAC. Do NOT change the VARIAC voltage setting.

Figure 2
Figure 2: Pin assignment of the SCR.

3. Half-Wave Rectifier SCR Circuit with Resistive Load and Non-Zero Firing Angle

Two different resistors will be used as R2. The values should be between 100 and 1000 Ω. The resistance can read the resistance color code, or measured with a digital multimeter.

  1. Angle Setting #1 (small R2)
    1. Remove the short circuit, which was previously used instead of R2.
    2. Connect the small resistance value for R2.
    3. Turn the VARIAC ON.
    4. Adjust the time base on the scope to show Vout for the same number of fundamental cycles captured for Vin. Make a copy of the waveforms.
    5. Measure the average or mean Vout.
    6. Zoom in between the SCR turn-off point and the next SCR turn-on point. Measure the time difference using the scope cursors. Make a copy of the waveform.
    7. Keep the differential probe connection and other circuit connections the same for the next part.
    8. Turn OFF the VARIAC. Do NOT disassemble the circuit or change the VARIAC voltage setting.
  2. Angle Setting #2 (small R2)
    1. Replace R2 with the larger value resistor.
    2. Turn the VARIAC ON.
    3. Adjust the time base on the scope to show Vout for the same number of fundamental cycles captured for Vin. Make a copy of the waveforms.
    4. Measure the average or mean Vout.
    5. Zoom in between the SCR turn-off point and the next SCR turn-on point. Measure the time difference using the scope cursors. Make a copy of the waveform. The mean value should be what is expected from this equation:
      <Vout>=V0[1+cos(α)]/(2π) (1)
      which is slightly less than half the peak voltage of the input.
    6. Turn OFF the VARIAC. Disassemble the circuit and return the VARIAC setting to zero.

Results

The AC input voltage waveform is chopped until the firing angle. Important relationships of the average output voltage and firing angles for different SCR rectifiers with input Vin= V0 cos(ωt) are:

• Single SCR and R load: <Vout>=V0[1+cos(α)]/(2π)  (2)

• SCR bridge and R load: <Vout>= V0[1+cos(α)]/π  (3)

• SCR bridge, current source load: <Vout>=2V0 cos(α)/π  (4)

As the firing angle increases, the mean or DC voltage at the output decreases as the output voltage waveform across the resistive load is a chopped version of the input.

Application and Summary

SCR's were common in older DC power supplies that required a variable DC output voltage from an AC input. By adjusting the resistor R2 in the above circuit, it is possible to adjust the average Vout and therefor an adjustable DC power supply results. SCRs are not common any more in DC power supplies as they switch at the input line frequency (typically 50 or 60 Hz), and new power supplies switch at 10 s or 100 s of kHz which makes filtering the output voltage to extract the DC component much easier with smaller capacitors. However, SCRs are still common in high voltage inverters where the switching frequency can be low at the line frequency since many high voltage and high current SCR's are available in the market.

Tags

ThyristorSilicon Controlled RectifierSCRLight DimmersMotor Speed ControllersVoltage RegulatorsDiodeAnodeCathodeGateCurrent FlowLatching ThresholdRectifyAC PowerPNPN StructureCircuitLoad

Skip to...

0:06

Overview

1:19

Principles of the Thyristor Rectifier

3:36

Equipment Setup

5:45

Half-Wave Rectifier Thyristor Circuit with Zero Firing Angle

7:01

Half-Wave Rectifier Thyristor Circuit with Non-zero Firing Angle

8:29

Results

9:06

Applications

10:08

Summary

Videos from this collection:

article

Now Playing

Thyristor Rectifier

Electrical Engineering

17.5K Views

article

Electrical Safety Precautions and Basic Equipment

Electrical Engineering

144.5K Views

article

Characterization of Magnetic Components

Electrical Engineering

15.0K Views

article

Introduction to the Power Pole Board

Electrical Engineering

12.4K Views

article

DC/DC Boost Converter

Electrical Engineering

56.8K Views

article

DC/DC Buck Converter

Electrical Engineering

21.1K Views

article

Flyback Converter

Electrical Engineering

13.2K Views

article

Single Phase Transformers

Electrical Engineering

20.1K Views

article

Single Phase Rectifiers

Electrical Engineering

23.4K Views

article

Single Phase Inverter

Electrical Engineering

17.9K Views

article

DC Motors

Electrical Engineering

23.3K Views

article

AC Induction Motor Characterization

Electrical Engineering

11.6K Views

article

VFD-fed AC Induction Machine

Electrical Engineering

6.9K Views

article

AC Synchronous Machine Synchronization

Electrical Engineering

21.6K Views

article

AC Synchronous Machine Characterization

Electrical Engineering

14.2K Views

JoVE Logo

Privacy

Terms of Use

Policies

Contact Us

Recommend to library

JoVE NEWSLETTERS

Research

Education

Authors

Librarians

ABOUT JoVE

Copyright © 2025 MyJoVE Corporation. All rights reserved