This work was supported by the Natural Science Foundation of Chongqing, China (cstc2019jcyj-msxmX0046), the project of Chongqing Education Commission of China (KJQN202001127), and the project of Banan District Science and Technology Commission, Chongqing, China (2020TJZ010). The authors would like to thank Prof. Yan Yang for providing the test site. We are also grateful to Dr. Jingshu Wang and Dr. Jinghua Ma for their guidance of using the vibration measurement instrumentation. Thanks are also due to the subjects for their wholehearted cooperation during the experiments.

All procedures were approved by the Ethics Committee of Chongqing University of Technology and each subject provided written informed consent prior to participation in this study.
1. Hand tractor preparation
<ol>
	<li>Ensure the hand tractor is subjected to proper test conditions with a full fuel tank, without looseness of bolts, and without other mechanical defects that would result in abnormal vibration. 
	NOTE: The specifications of the hand tractor used in this experiment are given in Table 1.</li>
	<li>Place the hand tractor in a test site with a dry, firm, and level ground surface. 
	NOTE: If this experiment was conducted in an indoor laboratory, the laboratory must be well-ventilated to prevent any injurious effects of the exhaust gas from the hand tractor.</li>
	<li>Remove the dust cover of the engine pulley to conveniently calibrate the engine speed with a speedometer during the experiment.</li>
	<li>Remove the elastomeric materials of the handles according to ISO 5349-2 standard5.</li>
</ol>
2. Subject preparation
<ol>
	<li>Ensure that all subjects are healthy with no physical ailment and are above the age of 18 years3. Inform each subject about the study objectives and test procedures. Obtain written informed consent from all subjects.
	<ol>
		<li>Exclude subjects with the following diseases: primary Raynaud&#39;s disease or secondary Raynaud&#39;s phenomenon, impairment of blood circulation to the hands, deformity of bones and joints, disorders of the peripheral nervous system or musculoskeletal system3.</li>
	</ol>
	</li>
	<li>Ask subjects to wear sleeveless or short-sleeved clothing, and to remove watches, bracelets, rings, etc.</li>
	<li>Warn each subject not to touch the gear shift lever of the hand tractor during operation. Warn each subject to stay away from the engine pulley when the hand tractor is running.</li>
	<li>Provide subjects with speed regulation training on the hand tractor. Inform each subject to shut down the engine at the end of the experiment by pressing down on the engine switch button. 
	NOTE: Generally, the engine speed regulation is controlled by the throttle switch located on the right handle, and subjects are trained to regulate the engine speed by turning the throttle switch to the left (speed decrease) or to the right (speed increase) with their right hands.</li>
	<li>Instruct each subject how to operate the hand tractor and how to regulate the engine speed from 1500 rpm to 3500 rpm.</li>
	<li>Measure each subject&#39;s body dimensions (standing height, mass, forearm length, upper arm length, hand length). 
	NOTE: Table 2 summarizes the physical characteristics of ten healthy subjects in this experiment.</li>
	<li>Wrap the accelerometer adapters tightly on the hand and arm of each subject at the locations indicated in Figure 2. 
	&#8203;NOTE: Each adapter was fabricated using a nylon strap and a piece of the galvanized iron sheet (0.3 mm) to provide a rigid and light attachment.</li>
</ol>
3. Measurement system setup
<ol>
	<li>Acceleration measurement system setup 
	NOTE: The present steps aim to collect the vibration acceleration signals from the handle of the hand tractor and six locations of operator&#39;s hand-arm system. The proposed approach employs a compact Data Acquisition (DAQ) system composed of seven accelerometers, three data acquisition cards, a DAQ chassis, a laptop computer, and some associated cables (Figure 3). Other types of DAQ systems with proper characteristics for the involved application can be similarly applied.
	<ol>
		<li>Before initiating a measurement, gather all the components of the measurement system (accelerometers, data acquisition system, thin-film pressure sensing system, tachometer, digital goniometer, and other relevant components).</li>
		<li>To set up the acceleration measurement system, connect the accelerometer with the data acquisition cards using the accelerometer cables. Using an Ethernet cable, connect the chassis with the computer. 
		NOTE: Two tri-axial accelerometers and five single-axis accelerometers fixed with magnetic mounting base were used in this experiment.</li>
		<li>Attach one tri-axial accelerometer on the left handle of the hand tractor and attach the other one on the accelerometer adapter of the subject&#39;s hand. Attach single-axis accelerometers, one by one, on the accelerometer adapters of the subject&#39;s arm and shoulder. 
		NOTE: The locations of the accelerometers are as shown in Figure 1. The location selection of the tri-axial accelerometer on the left handle of the hand tractor should be as close to the operator&#39;s left hand as possible.</li>
		<li>Adjust the orientation of the tri-axial accelerometers on the hand to be consistent with the basicentric coordinate system (Figure 4) for measurement of hand-arm vibration refer to ISO 5349-1 standard4. Using adhesive tape, secure the accelerometer cables on the skin surface of the subject&#39;s arm and the tractor&#39;s handlebar.</li>
	</ol>
	</li>
	<li>Grip force measurement setup 
	NOTE: A thin-film pressure sensing system15,16 was designed with two resistive pressure sensitive sensors, a single-chip controller, and an LED display, and was calibrated before measurement, as shown in Figure 5.
	<ol>
		<li>Attach two thin-film sensors symmetrically on opposite sides around the central axis of the handle using double-sided adhesive tape.</li>
		<li>Place the screen of the sensing system at a convenient height so that the subject could monitor and adjust the grip force to the specified level during the operation of the hand tractor.</li>
	</ol>
	</li>
	<li>Engine speed measurement setup 
	NOTE: Engine speed refers to the revolutions per minute (RPM) of the propeller of the employed hand tractor engine, which equals to the RPM of the engine pulley. A laser tachometer was used to calibrate and monitor the engine speed during operation.
	<ol>
		<li>Attach a piece of retroreflective tape (approximately 10 &#215; 10 mm) to the engine pulley surface for laser tachometer measurement.</li>
		<li>Place the tachometer at a proper height and perpendicular to the retroreflective tape.</li>
	</ol>
	</li>
	<li>Posture measurement
	<ol>
		<li>Instruct the subject to hold and raise the handle to a horizontal position. Measure the subject&#39;s hand and arm posture using a digital goniometer. 
		&#8203;NOTE: The five angles17 used to describe the hand and arm posture during the operation of the hand tractor are shown in Figure 6. The subjects&#39; posture angles measured in this experiment are presented in Table 2.</li>
		<li>Ask the subject to maintain the posture until the end of the trial.</li>
	</ol>
	</li>
</ol>
4. Experiment and data acquisition
<ol>
	<li>Start the hand tractor in neutral and keep it running at a low engine speed (around 1500 rpm) for about 30 s until it stabilized.</li>
	<li>Turn on the tachometer, the thin-film pressure sensing device, the laptop computer and the acceleration data acquisition system, respectively.</li>
	<li>Open the DAQ software and create a new file for each subject. Set the parameters of acceleration, acquisition mode, and sampling rate for data collection. 
	NOTE: To obtain the accurate characterization of the HTV, the sampling rate should be no less than 1500 Hz. In this study, the sampling rate was set at 1650 Hz. If a more higher sampling rate was used for data collection, a low-pass filter with a cut-off frequency at 1500 Hz was advised to remove the noise influences such as the irrelevant high-frequency contributions.</li>
	<li>Click the Run and wait about 10 s until the system is stabilized. Then click Record to start recording the acceleration data.</li>
	<li>Adjustment of the engine speed and grip force 
	NOTE: As shown in Figure 7, this experiment was conducted at three levels of engine speed (1500, 2500 and 3500 rpm) and three levels of grip force (20, 30, and 40 N) during each trial. The approximate duration of each subject&#39;s HTV testing is 6 min.
	<ol>
		<li>Ask the subject to monitor the tachometer and adjust the engine speed to 1500 rpm until it stabilized.</li>
		<li>Instruct the subject adjust the grip force carefully to 20 N by looking at the displayed force signals from the thin-film pressure sensing system, and keep this grip force level for about 30 s. 
		NOTE: The adjustment of the grip force denotes the increase or decrease of pressure between the hand and the handlebar of the hand tractor. Subjects should perform the adjustment of the grip force through holding the handlebar more tightly or lightly.</li>
		<li>Adjust the grip force to 30 N and keep about 30 s. Then, adjust the grip force to 40 N and keep about 30 s.</li>
		<li>Adjust the engine speed to 2500 rpm and repeat steps 4.5.2 and 4.5.3.</li>
		<li>Adjust the engine speed to 3500 rpm and repeat steps 4.5.2 and 4.5.3.</li>
	</ol>
	</li>
	<li>Ask the subject to turn the throttle switch to the lowest engine speed. Put down the handle and shut down the engine of the hand tractor.</li>
	<li>Save the data and shut down the DAQ system. Remove and place the accelerometers on the next subject.</li>
	<li>Repeat steps 4.3 to 4.7 until the end of the data collections of all subjects.</li>
	<li>Export the acceleration time-series data for further analysis.</li>
</ol>
5. Data processing and analysis
<ol>
	<li>Import the recorded vibration time domain signals to MATLAB software. Calculate the root-mean-square (RMS) values of the vibration acceleration of hand tractor&#39;s handle, which represent the vibration exposure during the operation of the hand tractor, with the Equation (1): 
	<img alt="Equation 1" src="/files/ftp_upload/62508/62508eq01.jpg" /> (1) 
	where, aRMS&#160;is the RMS of vibration acceleration (m/s2) calculated for each 1/3rd octave band, a(t) is the measured vibration acceleration amplitude (m/s2), and T&#160;is the duration of the measured vibration acceleration (s). 
	NOTE: In ISO 5349-1 standard, it is important to use RMS acceleration to represent the magnitude of vibrations transmitted to the operator&#39;s hands.</li>
	<li>Calculate the RMS values of vibration acceleration on hand, wrist, arm and shoulder of each subject using Equation (1). Calculate the vibration transmissibility (TR) using Equation (2)1,14: 
	<img alt="Equation 2" src="/files/ftp_upload/62508/62508eq02.jpg" /> (2) 
	where, ain is the handle vibration for HTV, and aout is the respective vibration in the six locations of the subject&#39;s hand-arm system (see Figure 2). 
	NOTE: According to ISO 5349-1, the factors (except for grip force and vibration frequency) may influence the results of hand transmitted vibration measurement include: the operator&#39;s skill, body posture, climatic conditions, noise, etc. To decrease these random factors, the TR values of all the measurement locations of the ten subjects in this study were averaged.</li>
	<li>Convert the time domain signals of the handle to frequency domain signals by fast Fourier transform (FFT) algorithm using MATLAB program to examine the input vibration.</li>
</ol>

<ol>
	<li>Ahmadian, H., Hassan-Beygi, S. R., Ghobadian, B., Najafi, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=ANFIS+modeling+of+vibration+transmissibility+of+a+power+tiller+to+operator.">ANFIS modeling of vibration transmissibility of a power tiller to operator.</a> Applied Acoustics. 138, 39-51 (2018).</li><li>Heaver, C., Goonetilleke, K. S., Ferguson, H., Shiralkar, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hand-arm+vibration+syndrome:+a+common+occupational+hazard+in+industrialized+countries.">Hand-arm vibration syndrome: a common occupational hazard in industrialized countries.</a> Journal of Hand Surgery. 36 (5), 354-363 (2011).</li><li>Geethanjali, G., Sujatha, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Study+of+Biomechanical+Response+of+Human+Hand-Arm+to+Random+Vibrations+of+Steering+Wheel+of+Tractor.">Study of Biomechanical Response of Human Hand-Arm to Random Vibrations of Steering Wheel of Tractor.</a> Molecular &amp; Cellular Biomechanics. 10 (4), 303-317 (2013).</li><li>International Organization for Standardization. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=ISO+5349-1:+Mechanical+Vibration:+Measurement+and+Evaluation+of+Human+Exposure+to+Hand+Transmitted+Vibration+Part+1:+General+requirements.">ISO 5349-1: Mechanical Vibration: Measurement and Evaluation of Human Exposure to Hand Transmitted Vibration Part 1: General requirements.</a> International Organization for Standardization. , (2001).</li><li>International Organization for Standardization. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=ISO5349-2:+Mechanical+vibration-+Measurement+and+evaluation+of+human+exposure+to+hand-transmitted+vibration.+Part+2:+Practical+guidance+for+measurement+at+the+workplace.">ISO5349-2: Mechanical vibration- Measurement and evaluation of human exposure to hand-transmitted vibration. Part 2: Practical guidance for measurement at the workplace.</a> International Organization for Standardization. , (2001).</li><li>Besa, A. J., Valero, F. J., Su&#241;er, J. L., Carballeira, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Characterisation+of+the+mechanical+impedance+of+the+human+hand-arm+system:+The+influence+of+vibration+direction,+hand-arm+posture+and+muscle+tension.">Characterisation of the mechanical impedance of the human hand-arm system: The influence of vibration direction, hand-arm posture and muscle tension.</a> International Journal of Industrial Ergonomics. 37 (3), 225-231 (2007).</li><li>Marcotte, P., Aldien, Y., Boileau, P. &. #. 2. 0. 1. ;., Rakheja, S., Boutin, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+handle+size+and+hand-handle+contact+force+on+the+biodynamic+response+of+the+hand-arm+system+under+zh-axis+vibration.">Effect of handle size and hand-handle contact force on the biodynamic response of the hand-arm system under zh-axis vibration.</a> Journal of Sound and Vibration. 283 (3-5), 1071-1091 (2005).</li><li>Pan, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+relationships+between+hand+coupling+force+and+vibration+biodynamic+responses+of+the+hand-arm+system.">The relationships between hand coupling force and vibration biodynamic responses of the hand-arm system.</a> Ergonomics. 61 (6), 818-830 (2018).</li><li>Dong, R. G., Rakheja, S., Schopper, A. W., Han, B., Smutz, W. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hand-transmitted+vibration+and+biodynamic+response+of+the+human+hand-arm:+a+critical+review.">Hand-transmitted vibration and biodynamic response of the human hand-arm: a critical review.</a> Critical Reviews In Biomedical Engineering. 29 (4), 393-439 (2001).</li><li>Marchetti, E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+investigation+on+the+vibration+transmissibility+of+the+human+elbow+subjected+to+hand-transmitted+vibration.">An investigation on the vibration transmissibility of the human elbow subjected to hand-transmitted vibration.</a> International Journal of Industrial Ergonomics. 62, 82-89 (2017).</li><li>McDowell, T. W., Welcome, D. E., Warren, C., Xu, X. S., Dong, R. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Assessment+of+hand-transmitted+vibration+exposure+from+motorized+forks+used+for+beach-cleaning+operations.">Assessment of hand-transmitted vibration exposure from motorized forks used for beach-cleaning operations.</a> Annals of Work Exposures and Health. 57 (1), 43-53 (2013).</li><li>Tony, B. J. A. R., Alphin, M. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Finite+element+analysis+to+assess+the+biomechanical+behavior+of+a+finger+model+gripping+handles+with+different+diameters.">Finite element analysis to assess the biomechanical behavior of a finger model gripping handles with different diameters.</a> Biomedical Human Kinetics. 11 (1), 69-79 (2019).</li><li>Tony, B. J. A. R., Alphin, M. S., Velmurugan, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Influence+of+handle+shape+and+size+to+reduce+the+hand-arm+vibration+discomfort.">Influence of handle shape and size to reduce the hand-arm vibration discomfort.</a> Work. 63 (3), 415-426 (2019).</li><li>Dewangan, V. K. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Characteristics+of+hand-transmitted+vibration+of+a+hand+tractor+used+in+three+operational+modes.">Characteristics of hand-transmitted vibration of a hand tractor used in three operational modes.</a> International Journal of Industrial Ergonomics. 39 (1), 239-245 (2009).</li><li>Kalra, M., Rakheja, S., Marcotte, P., Dewangan, K. N., Adewusi, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Measurement+of+coupling+forces+at+the+power+tool+handle-hand+interface.">Measurement of coupling forces at the power tool handle-hand interface.</a> International Journal of Industrial Ergonomics. 50, 105-120 (2015).</li><li>Gurram, R., Rakheja, S., Gouw, G. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+study+of+hand+grip+pressure+distribution+and+EMG+of+finger+flexor+muscles+under+dynamic+loads.">A study of hand grip pressure distribution and EMG of finger flexor muscles under dynamic loads.</a> Ergonomics. 38 (4), 684-699 (1995).</li><li>Tarabini, M., Saggin, B., Scaccabarozzi, D., Moschioni, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Hand-arm+mechanical+impedance+in+presence+of+unknown+vibration+direction.">Hand-arm mechanical impedance in presence of unknown vibration direction.</a> International Journal of Industrial Ergonomics. 43 (1), 52-61 (2013).</li><li>Aatola, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transmission+of+vibration+to+the+wrist+and+comparison+of+frequency+response+function+estimators.">Transmission of vibration to the wrist and comparison of frequency response function estimators.</a> Journal of Sound and Vibration. 131 (3), 497-507 (1989).</li><li>Kihlberg, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Biodynamic+response+of+the+hand-arm+system+to+vibration+from+an+impact+hammer+and+a+grinder.">Biodynamic response of the hand-arm system to vibration from an impact hammer and a grinder.</a> International Journal of Industrial Ergonomics. 16 (1), 1-8 (1995).</li><li>Gurram, R., Rakheja, S., Gouw, G. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vibration+transmission+characteristics+of+the+human+hand-arm+and+gloves.">Vibration transmission characteristics of the human hand-arm and gloves.</a> International Journal of Industrial Ergonomics. 13 (3), 217-234 (1994).</li><li>Burstr&#246;m, A. S. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Transmission+of+vibration+energy+to+different+parts+of+the+human+hand-arm+system.">Transmission of vibration energy to different parts of the human hand-arm system.</a> Int Arch Occup Environ Health. 70 (3), 199-204 (1997).</li><li>Hartung, E., Dupuis, H., Scheffer, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+grip+and+push+forces+on+the+acute+response+of+the+hand-arm+system+under+vibrating+conditions.">Effects of grip and push forces on the acute response of the hand-arm system under vibrating conditions.</a> International Archives of Occupational and Environmental Health. 64 (6), 463-467 (1993).</li><li>Pope, M. H., Magnusson, M., Hansson, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+upper+extremity+attenuates+intermediate+frequency+vibrations.">The upper extremity attenuates intermediate frequency vibrations.</a> Journal of Biomechanics. 30 (2), 103-108 (1997).</li><li>International Organization for Standardization. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=ISO+8041-1:+Human+response+to+vibration-Measuring+instrumentation.">ISO 8041-1: Human response to vibration-Measuring instrumentation.</a> International Organization for Standardization. , (2017).</li><li>Ying, Y. B., Zhang, L. B., Xu, F., Dong, M. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vibratory+characteristics+and+hand-transmitted+vibration+reduction+of+walking+tractor.">Vibratory characteristics and hand-transmitted vibration reduction of walking tractor.</a> Transactions Of The ASAE. 41 (4), 917-922 (1998).</li><li>Dewangan, K. N., Tewari, V. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Characteristics+of+vibration+transmission+in+the+hand-arm+system+and+subjective+response+during+field+operation+of+a+hand+tractor.">Characteristics of vibration transmission in the hand-arm system and subjective response during field operation of a hand tractor.</a> Biosystems Engineering. 100 (4), 535-546 (2008).</li><li>Xu, X. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Vibrations+transmitted+from+human+hands+to+upper+arm,+shoulder,+back,+neck,+and+head.">Vibrations transmitted from human hands to upper arm, shoulder, back, neck, and head.</a> International Journal of Industrial Ergonomics. 62, 1-12 (2017).</li></ol>

The authors have nothing to disclose.

The protocol presented in this study was established based on HTV standards4,5,24, and was developed as the standard steps for the measurement of the HTV of the human hand-arm system during the operation of a hand tractor in a stationary condition. This condition is the most stable state of the hand tractor to help ensure the reliable measurement of the vibration actually transmitted to the hand and arm. The range of variables considered to perform the test, via the adjustment of the engine speed and grip force, covers the normal and safe operating range of the hand tractor. Considering the complexity of the hand-arm system, the experimental results yielded from this protocol were found to agree well with data reported in articles on the characteristics of vibration sources25, vibration transmissibility1,26, and the essential factors8,27 that affect the response of the hand-arm system during the operation of hand tractors.
The results are dependent on some critical components of this setup within the protocol. First, because the weight of the accelerometer affects the magnitude of the vibration of the hand-arm system20, the total weight of the accelerometer and adapter should be as light as possible to reduce measurement errors. Second, each accelerometer adapter should be tightly secured on the hand-arm system to prevent any relative motion between the measurement point and the accelerometer.Third, the test trial of each subject should be completed without interruption to reduce the effect of the operating posture.
The main limitation of this study is that the vibration transmissibility to the hand-arm system was only measured and analyzed in the Z-axis direction (Figure 4) due to the use of single-axis accelerometers at the locations of arm and shoulder. Although flexible and thin-film sensors were used to measure grip force during the test, further measurement efforts along the shear direction are expected to provide considerable insights into the characterization and assessment of HTV, which represents another limitation of the present study. Additionally, the intrinsic factors of operators, such as their body size, body posture, and hand and arm size, influence HTV. As a subsequent step, more data will be collected to examine these factors using the presented protocol.
This protocol will be helpful for the understanding of the vibration transmission characteristics of the hand tractor-hand-arm system. The main potential applications of the proposed methodology are the estimation of human-tractor interaction phenomena, the ergonomics development of hand tractors, and the development of protective devices such as isolators and gloves.

Hand tractors, also known as power tillers, are widely used in developing countries for the land preparation of small fields. The field operation of a hand tractor involves walking behind the machine and holding its handles to control its movement. The operators of hand tractors are exposed to high levels of vibration, which could be attributed to the small single cylinder engine and lack of suspension system of hand tractors1. The hand-arm vibration syndrome (HAVS)2 can be caused by long-period endurance from the vibration, named hand transmitted vibration (HTV), which generated by the hand tractor and received by the operator&#39;s hands. To assess the health risks derived by operators&#39; exposure to the HTV of hand tractors, it is necessary to establish a method for the measurement of the vibration response of the hand-arm system.
The hand-arm system is composed of bones, muscles, tissues, veins and arteries, tendons and skin3, and the direct measurement of HTV poses many problems. The relevant international standards4,5 provide guidelines pertaining to the measurement of the severity of vibration generated in the immediate vicinity of the hand, including the coordinate system for the hand, the location and mounting of accelerometers, the measurement duration, cable connector problems, etc. However, the standards do not take into consideration intrinsic variables, such as the grip force, the posture of the hand and arm, individual factors, etc. These factors have been examined extensively under a wide range of vibration excitations and test conditions6,7,8,9,10,11,12,13, but the results of different investigators are not in good agreement. Many of these factors have not been sufficiently understood to be incorporated into standard methods. This restriction is partially attributable to the complexities of the human hand-arm system, the test conditions, and the differences in the experimental and measurement techniques employed.
Moreover, most of the earlier measurements of HTV were performed under carefully controlled conditions with idealized vibration excitations, grip force, and postural conditions. The findings and experimental procedures of these measurements, therefore, may not truly replicate real-world conditions, such as the operating conditions of hand tractors. Moreover, only limited efforts have been undertaken to study the HTV of hand tractors with field measurements. These measurements were performed using accelerometers attached to the operator&#39;s wrist, arm, chest, and head to measure the whole body vibration under the tractor&#39;s transportation conditions1, or under the conditions of tilling in an untilled field and puddling in a submerged field with different levels of engine speeds14. The effect of the grip force, which could be a crucial factor of HTV7,8, was not isolated. These methods are therefore unsuitable as standardized measurement procedures due to the operator&#39;s various forced postures during farming ascribed to the harsh environmental conditions.
The present research was undertaken to contribute to the establishment of reliable and repeatable procedures for the HTV measurement of hand tractors in a stationary mode. Figure 1 presents the schematic diagram of the experimental design. A hand tractor manufactured in China and commonly used by Chinese farmers was employed, and ten research workers were chosen as subjects for the study. Seven lightweight piezoelectric accelerometers attached to the tractor-hand-arm system were used to measure the vibration. One tachometer and two thin-film pressure sensors monitored the engine speed and grip force during testing. The subjects were required to sequentially operate the hand tractor at specified engine speeds and with specified grip forces to obtain the vibration characteristics in various operational modes. This manuscript provides a detailed protocol for the HTV measurement of the tractor-hand-arm system with unique consideration of changes in the grip force and vibration frequency.

<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Accelerometers</td>
			<td>PCB Piezotronics Inc.</td>
			<td>352C33, 356A04</td>
			<td>Used to measure vibration signals. Including 2 tri-axial accelerometers and 5 single-axis accelerometers.</td>
		</tr>
		<tr>
			<td>CompactDAQ System</td>
			<td>National Instruments</td>
			<td>cRIO-9045,NI-9234 C</td>
			<td>Used for acceleration acquisition. The system consists of a chassis and 3 data acquisition cards.</td>
		</tr>
		<tr>
			<td>Digital caliper</td>
			<td>Sanliang</td>
			<td>160800635</td>
			<td>Used to measure dimensions of the hand.</td>
		</tr>
		<tr>
			<td>Digital goniometer</td>
			<td>Sanliang</td>
			<td>802973</td>
			<td>Used to measure hand and arm posture.</td>
		</tr>
		<tr>
			<td>Laptop computer</td>
			<td>Lenovo</td>
			<td>Ideapad 500s</td>
			<td>To run the softwares.</td>
		</tr>
		<tr>
			<td>Matlab</td>
			<td>MathWorks Inc.</td>
			<td>Version 2020a</td>
			<td>Used for data processing.</td>
		</tr>
		<tr>
			<td>NI SignalExpress</td>
			<td>National Instruments</td>
			<td>Trial version 2015</td>
			<td>Use to acquire, analyze and present acceleration data.</td>
		</tr>
		<tr>
			<td>Tachometer</td>
			<td>Sanliang</td>
			<td>TM 680</td>
			<td>Used to measure engine speed.</td>
		</tr>
		<tr>
			<td>Thin-film pressure sensing system</td>
			<td>YourCee</td>
			<td>n/a</td>
			<td>Used to measure grip force. The system consists of 2 thin-film sensors, a STM32 singlechip and a LED display.</td>
		</tr>
	</tbody>
</table>

measurement of the hand transmitted vibration of the human hand arm system during operation of a hand tractor

Operators of hand tractors are exposed to high levels of hand transmitted vibration (HTV). This vibration, which can be both irksome and hazardous to human health, is imparted to the operator via his or her hands and arms. However, a standardized method for measuring HTV of hand tractors has yet to be defined. The aim of the study was to present an experimental method for the investigation of the biodynamic response and vibration transmissibility of the hand-arm system during the operation of a hand tractor in a stationary mode. Measurements were performed with ten subjects using three grip forces and three handle vibration levels to examine the influences of the hand pressure and frequency on hand transmitted vibration (HTV). The results indicate that the tightness of grip on the handle influences the vibration response of the hand-arm system, especially at frequencies between 20 and 100 Hz. The transmission of lower frequencies in the hand-arm system was relatively unattenuated. In comparison, attenuation was found to be quite marked for higher frequencies during the operation of the hand tractor. The vibration transmissibility to different parts of the hand-arm system decreased with the increase of the distance from the vibration source. The proposed methodology contributes to the collection of consistent data for the evaluation of operator vibration exposure and the ergonomics development of hand tractors.

The experiment was carried out in the laboratory (air temperature 22.0 &#176;C &#177; 1.5 &#176;C) on ten healthy subjects (Table 2) during the operation of a hand tractor in a stationary condition.
Following the protocol, vibration acceleration data were collected from the handle of the hand tractor, as well as the back of the hand, the wrist, the arm, and the shoulder of each subject. The spectrum of the vibration acceleration occurring at the handle (input to the hand) was obtained. Figure 8 displays samples of the time domain and RMS frequency domain accelerations on the handle at the engine speed level of 3500 rpm for a given time duration. It is evident that the vibration acceleration was the highest along the Y-axis and the lowest along the X-axis. The maximum accelerations of the X and Z directions occurred at the frequency of 58 Hz (which is the working frequency of the engine corresponding to the rotational speed of 3500 rpm). Most of the vibration energy was found to be centralized in the frequency range from 50 to 200 Hz. With the same analytical process, the characteristics of both the time domain and frequency domain signals could be obtained, such as the vibration amplitude, peak, dominant frequency, etc.
The influences of the grip force and engine speed on the vibration response of the hand-arm system were also examined. As shown in Figure 9, it was observed that the increase in the grip force increased the vibration acceleration notably at frequencies between 20 and 100 Hz, and three resonance frequencies (20, 40, and 80 Hz) were found to increase almost linearly with the increase of the grip force. This is attributed to the increase of the contact stiffness and joint stiffness18,19. These findings indicate that the presented measurement and adjustment methods of the grip force could be effectively applied to HTV measurement.
As shown in Figure 10, this experiment examined the effect of the input frequency on HTV via engine speed adjustment at three levels (1500, 2500, and 3500 rpm). At the location of the back of the hand (Figure 10A), a higher value of acceleration was obtained at 3500 rpm compared to lower engine speeds. In contrast, at the upper arm and shoulder (Figure 10D, E, and F), the peak acceleration occurred at 1500 rpm. Through the comprehensive comparison of both the locations and exciting frequencies, it is reasonable to conclude that lower frequencies were transmitted relatively unattenuated in the hand-arm system, while attenuation was quite marked for higher frequencies. Thus, most of the vibration energy was dissipated in the hand and forearm.
Figure 11&#160;presents the averaged transmissibility to the back of the hand, forearm, upper arm and shoulder from the ten subjects that are with engine speed of 2500 rpm and grip force of 30 N. It was found that the transmissibility to the different parts of the hand-arm system decreased with the increase of the distance from the vibration source. The highest transmissibility was observed at the back of the hand (location 1), with a peak value of 5.1 at around 80 Hz. The amplification of vibration may be due to the resonance of the skin at the metacarpal20,21. Consistent with the findings of previous studies22,23, the resonant frequency of the wrist (location 2) and elbow (location 4) transmissibility was around 20 Hz, with a magnitude of approximately 3.0. Additionally, the shoulder (location 6) transmissibility peak was 1.1 at around 10 Hz. It was also found that only vibrations of less than 25 Hz were effectively transmitted to the forearm, upper arm, and shoulder. With Equation (2) in section 5.2 and following the analytical process of the transmissibility, it is feasible to examine the influences on transmissibility with different exciting frequencies and changing grip force, and a reasonable suggestion of operating hand tractor for farmers could be made.
<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Engine model and type</td>
			<td>JUWEI FC 170, gasoline, single cylinder, four-stroke, OHV, forced-air cooled</td>
		</tr>
		<tr>
			<td>Swept volume, cc</td>
			<td>208</td>
		</tr>
		<tr>
			<td>Rated power, kW</td>
			<td>4.0 kW at 3600 rpm</td>
		</tr>
		<tr>
			<td>Maximum Torque, Nm/rpm</td>
			<td>12/2500</td>
		</tr>
		<tr>
			<td>Number of speeds</td>
			<td>2 forward, 1 reverse</td>
		</tr>
		<tr>
			<td>Start mode</td>
			<td>Recoil start (pull start)</td>
		</tr>
		<tr>
			<td>Dry weight of engine, kg</td>
			<td>19</td>
		</tr>
		<tr>
			<td>Weight of hand tractor with full fuel tank, radiator and lubricating oils, kg</td>
			<td>72</td>
		</tr>
		<tr>
			<td>Tyre type</td>
			<td>Rubber wheel</td>
		</tr>
		<tr>
			<td>Tyre size(pneumatic), mm</td>
			<td>155&#215;330 (350-6)</td>
		</tr>
	</tbody>
</table>
Table 1. Specifications of the hand tractor.
<table border="1" fo:keep-together.within-page="1" fo:keep-with-next.within-page="always">
	<tbody>
		<tr>
			<td>Dimensions and Postures</td>
			<td>Minimum</td>
			<td>Maximum</td>
			<td>Mean</td>
			<td>SD</td>
		</tr>
		<tr>
			<td>Age, years</td>
			<td>18</td>
			<td>37</td>
			<td>22.6</td>
			<td>5.6</td>
		</tr>
		<tr>
			<td>Weight, kg</td>
			<td>50</td>
			<td>72</td>
			<td>62.6</td>
			<td>7.3</td>
		</tr>
		<tr>
			<td>Stature, cm</td>
			<td>164</td>
			<td>179</td>
			<td>172.1</td>
			<td>4.7</td>
		</tr>
		<tr>
			<td>Forearm hand length, cm</td>
			<td>22.1</td>
			<td>26.8</td>
			<td>25.2</td>
			<td>1.3</td>
		</tr>
		<tr>
			<td>Upper arm length, cm</td>
			<td>26.8</td>
			<td>34</td>
			<td>31.1</td>
			<td>2.1</td>
		</tr>
		<tr>
			<td>Hand length, cm</td>
			<td>15.2</td>
			<td>21</td>
			<td>17.1</td>
			<td>1.6</td>
		</tr>
		<tr>
			<td>Shoulder horizontal abduction (&#945;), degrees</td>
			<td>22.6</td>
			<td>31.5</td>
			<td>27.1</td>
			<td>3.2</td>
		</tr>
		<tr>
			<td>Shoulder vertical abduction (&#946;) , degrees</td>
			<td>16.5</td>
			<td>24.2</td>
			<td>20.7</td>
			<td>2.6</td>
		</tr>
		<tr>
			<td>Elbow extension (&#947;) , degrees</td>
			<td>134.1</td>
			<td>169.3</td>
			<td>150.1</td>
			<td>10.9</td>
		</tr>
		<tr>
			<td>Wrist extension (&#952;) , degrees</td>
			<td>160.5</td>
			<td>174.8</td>
			<td>169</td>
			<td>5.5</td>
		</tr>
		<tr>
			<td>Wrist deviation (&#969;) , degrees</td>
			<td>139.2</td>
			<td>159.5</td>
			<td>148.1</td>
			<td>5.6</td>
		</tr>
	</tbody>
</table>
Table 2. Subject physical characteristics.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/62508/62508fig01.jpg" /> 
Figure 1. The experimental protocol and data acquisition set up. This example depicts a single trial (from right to left) for the measurement of a subject&#39;s body dimensions, the wearing of 6 accelerometer adapters, the operating posture of the hand tractor, and the data acquisition set up for the acceleration, grip force, and engine speed. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig01large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/62508/62508fig02.jpg" /> 
Figure 2. The locations of the accelerometer adapters. 6 accelerometer adapters were wrapped in the locations of back of the hand, distal end of the forearm, proximal end of the forearm, distal end of the upper arm, proximal end of the upper arm and the acromion along the hand-arm system. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig02large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/62508/62508fig03.jpg" /> 
Figure 3. Vibration measurement instrumentation. The components of the measurement system including accelerometers, data acquisition system, thin-film pressure sensing system, a tachometer, a digital goniometer and other relevant components (computer, accelerometer adapters, cables, tape measure, thermometer). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig03large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/62508/62508fig04.jpg" /> 
Figure 4. The basicentric coordinate system for hand-arm vibration measurement. The&#160;X-axis is defined parallel to the longitudinal axis of the grip. The Y-axis is directed along the third metacarpus bone of the hand. The Z-axis is perpendicular to the palm surface area. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig04large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 5" class="xfigimg" src="/files/ftp_upload/62508/62508fig05.jpg" /> 
Figure 5. The thin-film pressure sensing system. This system consists of two thin-film sensors, a single-chip controller, and an LED display to show the real time grip force. The test data can also be exported to a computer by the serial communication. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig05large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 6" class="xfigimg" src="/files/ftp_upload/62508/62508fig06.jpg" /> 
Figure 6. The five angles used to describe the hand and arm posture. &#945; describes the shoulder horizontal abduction, &#946; describes the shoulder vertical abduction, &#947; identifies the elbow extension, &#952;&#160;characterizes the wrist extension, and &#969; identifies the wrist deviation. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig06large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 7" class="xfigimg" src="/files/ftp_upload/62508/62508fig07.jpg" /> 
Figure 7. Adjustment of the engine speed and grip force during the experiment. The blue bars represent different grip forces of 20, 30, and 40 N. The red lines indicate adjustment of engine speed from 1500, 2500 to 3500 rpm. Therefore, there are 9 test cases from 1500 rpm, 20 N to 3500 rpm, 40 N. The duration of each test case is about 30 s. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig07large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 8" class="xfigimg" src="/files/ftp_upload/62508/62508fig08.jpg" /> 
Figure 8. Samples of the time domain wave and amplitude spectra of the accelerations on handle at the engine speed of 3500 rpm. (A) The time domain wave and (B) amplitude spectra in the X direction; (C) the time domain wave and (D) amplitude spectra in the Y direction; (E) the time domain wave and (F) amplitude spectra in the Z direction. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig08large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 9" class="xfigimg" src="/files/ftp_upload/62508/62508fig09.jpg" /> 
Figure 9. The mean relationship between the grip force and RMS vibration acceleration measured at six locations of the hand-arm system of ten subjects: (A) back of the hand; (B) distal end of the forearm; (C) proximal end of the forearm; (D) distal end of the upper arm; (E) proximal end of the upper arm; (F) acromion. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig09large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 10" class="xfigimg" src="/files/ftp_upload/62508/62508fig10.jpg" /> 
Figure 10. The mean relationship between the engine speed (frequency) and RMS vibration acceleration measured at six locations of the hand-arm system of ten subjects: (A) back of the hand; (B) distal end of the forearm; (C) proximal end of the forearm; (D) distal end of the upper arm; (E) proximal end of the upper arm; (F) acromion. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig10large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 11" class="xfigimg" src="/files/ftp_upload/62508/62508fig11.jpg" /> 
Figure 11. Vibration transmissibility at the 1/3rd octave band at different locations in the hand-arm system at the engine speed of 2500 rpm and grip force of 30 N. The 6 curves represent the TR values from back of the hand (location 1) to the acromion (location 6) as shown in the legend. The dashed line is a dividing line of vibration amplification (above this line) and vibration attenuation (below this line). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/62508/62508fig11large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor at JoVE.com

Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor

Here, we present a standardized method for measurement of the hand transmitted vibration from handles of a single-axle tractor with special reference to changes in grip force and vibration frequency.

Operators of hand tractors are exposed to high levels of hand transmitted vibration (HTV). This vibration, which can be both irksome and hazardous to ...

measurement-hand-transmitted-vibration-human-hand-arm-system-during

Nanyang Technological University

Research

JoVE Journal

Engineering

4.3K Views.  Chongqing University of Technology. Here, we present a standardized method for measurement of the hand transmitted vibration from handles of a single-axle tractor with special reference to changes in grip force and vibration frequency.

Video: Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor

Experimental Measurement of Settling Velocity of Spherical Particles in Unconfined and Confined Surfactant-based Shear Thinning Viscoelastic Fluids

An experimental study is performed to measure the terminal settling velocities of spherical particles in surfactant based shear thinning viscoelastic (VES) fluids. The measurements are made for particles settling in unbounded fluids&#160;and fluids between parallel walls. VES fluids over a wide range of rheological properties are prepared and rheologically characterized. The rheological characterization involves steady shear-viscosity and dynamic oscillatory-shear measurements to quantify the viscous and elastic properties respectively. The settling velocities under unbounded conditions are measured in beakers having diameters at least 25x the diameter of particles. For measuring settling velocities between parallel walls, two experimental cells with different wall spacing are constructed. Spherical particles of varying sizes are gently dropped in the fluids and allowed to settle. The process is recorded with a high resolution video camera and the trajectory of the particle is recorded using image analysis software. Terminal settling velocities are calculated from the data.
The impact of elasticity on settling velocity in unbounded fluids is quantified by comparing the experimental settling velocity to the settling velocity calculated by the inelastic drag predictions of Renaud et al.1&#160;Results show that elasticity of fluids can increase or decrease the settling velocity. The magnitude of reduction/increase is a function of the rheological properties of the fluids and properties of particles. Confining walls are observed to cause a retardation effect on settling and the retardation is measured in terms of wall factors.

This paper demonstrates the experimental procedure to measure terminal settling velocities of spherical particles in surfactant-based shear thinning viscoelastic fluids. Fluids over a wide range of rheological properties are prepared and settling velocities are measured for a range of particle sizes in unbounded fluids and fluids between parallel walls.

An experimental study is performed to measure the terminal settling velocities of spherical particles in surfactant based shear thinning viscoelastic ...

Integrating a Triplet-triplet Annihilation Up-conversion System to Enhance Dye-sensitized Solar Cell Response to Sub-bandgap Light

The poor response of dye-sensitized solar cells (DSCs) to red and infrared light is a significant impediment to the realization of higher photocurrents and hence higher efficiencies. Photon up-conversion by way of triplet-triplet annihilation (TTA-UC) is an attractive technique for using these otherwise wasted low energy photons to produce photocurrent, while not interfering with the photoanodic performance in a deleterious manner. Further to this, TTA-UC has a number of features, distinct from other reported photon up-conversion technologies, which renders it particularly suitable for coupling with DSC technology. In this work, a proven high performance TTA-UC system, comprising a palladium porphyrin sensitizer and rubrene emitter, is combined with a high performance DSC (utilizing the organic dye D149) in an integrated device. The device shows an enhanced response to sub-bandgap light over the absorption range of the TTA-UC sub-unit resulting in the highest figure of merit for up-conversion assisted DSC performance to date.

An integrated device, incorporating a dye-sensitized solar cell and triplet-triplet annihilation up-conversion unit was produced, affording enhanced light harvesting, from a wider section of the solar spectrum. Under modest irradiation levels a significantly enhanced response to low energy photons was demonstrated, yielding a record figure of merit for dye-sensitized solar cells.

The poor response of dye-sensitized solar cells (DSCs) to red and infrared light is a significant impediment to the realization of higher photocurrents ...

Fabrication and Operation of a Nano-Optical Conveyor Belt

The technique of using focused laser beams to trap and exert forces on small particles has enabled many pivotal discoveries in the nanoscale biological and physical sciences over the past few decades. The progress made in this field invites further study of even smaller systems and at a larger scale, with tools that could be distributed more easily and made more widely available. Unfortunately, the fundamental laws of diffraction limit the minimum size of the focal spot of a laser beam, which makes particles smaller than a half-wavelength in diameter hard to trap and generally prevents an operator from discriminating between particles which are closer together than one half-wavelength. This precludes the optical manipulation of many closely-spaced nanoparticles and&#160;limits the&#160;resolution of optical-mechanical systems. Furthermore, manipulation using focused beams requires beam-forming or steering optics, which can be very bulky and expensive. To address these limitations in the system scalability of conventional optical trapping our lab has devised an alternative technique which utilizes near-field optics to move particles across a chip. Instead of focusing laser beams in the far-field, the optical near field of plasmonic resonators produces the necessary local optical intensity enhancement to overcome the restrictions of diffraction and manipulate particles at higher resolution. Closely-spaced resonators produce strong optical traps which can be addressed to mediate the hand-off of particles from one to the next in a conveyor-belt-like fashion. Here, we describe how to design and produce a conveyor belt using a gold surface patterned with plasmonic C-shaped resonators and how to operate it with polarized laser light to achieve super-resolution nanoparticle manipulation and transport. The nano-optical conveyor belt chip can be produced using lithography techniques and easily packaged and distributed.

The scalability and resolution of conventional optical manipulation techniques are limited by diffraction. We circumvent the diffraction limit and describe a method of optically transporting nanoparticles across a chip using a gold surface patterned with a path of closely spaced C-shaped plasmonic resonators.

The technique of using focused laser beams to trap and exert forces on small particles has enabled many pivotal discoveries in the nanoscale biological ...

Development of an Experimental Setup for the Measurement of the Coefficient of Restitution under Vacuum Conditions

The Discrete Element Method is used for the simulation of particulate systems to describe and analyze them, to predict and afterwards optimize their behavior for single stages of a process or even an entire process. For the simulation with occurring particle-particle and particle-wall contacts, the value of the coefficient of restitution is required. It can be determined experimentally. The coefficient of restitution depends on several parameters like the impact velocity. Especially for fine particles the impact velocity depends on the air pressure and under atmospheric pressure high impact velocities cannot be reached. For this, a new experimental setup for free-fall tests under vacuum conditions is developed. The coefficient of restitution is determined with the impact and rebound velocity which are detected by a high-speed camera. To not hinder the view, the vacuum chamber is made of glass. Also a new release mechanism to drop one single particle under vacuum conditions is constructed. Due to that, all properties of the particle can be characterized beforehand.

The coefficient of restitution is a parameter that describes the loss of kinetic energy during collision. Here, a free-fall setup under vacuum conditions is developed to be able to determine the coefficient of restitution parameter for particles in micrometer range with high impact velocities.

The Discrete Element Method is used for the simulation of particulate systems to describe and analyze them, to predict and afterwards optimize their ...

The Measurement of Unsteady Surface Pressure Using a Remote Microphone Probe

Microphones are widely applied to measure pressure fluctuations at the walls of solid bodies immersed in turbulent flows. Turbulent motions with various characteristic length scales can result in pressure fluctuations over a wide frequency range. This property of turbulence requires sensing devices to have sufficient sensitivity over a wide range of frequencies. Furthermore, the small characteristic length scales of turbulent structures require small sensing areas and the ability to place the sensors in very close proximity to each other. The complex geometries of the solid bodies, often including large surface curvatures or discontinuities, require the probe to have the ability to be set up in very limited spaces. The development of a remote microphone probe, which is inexpensive, consistent, and repeatable, is described in the present communication. It allows for the measurement of pressure fluctuations with high spatial resolution and dynamic response over a wide range of frequencies. The probe is small enough to be placed within the interior of typical wind tunnel models. The remote microphone probe includes a small, rigid, and hollow tube that penetrates the model surface to form the sensing area. This tube is connected to a standard microphone, at some distance away from the surface, using a "T" junction. An experimental method is introduced to determine the dynamic response of the remote microphone probe. In addition, an analytical method for determining the dynamic response is described. The analytical method can be applied in the design stage to determine the dimensions and properties of the RMP components.

Here, we present a protocol to measure, with high spatial resolution, the unsteady surface pressure in turbulent flows. This method demonstrates the construction of a remote microphone probe (RMP) and the determination of its frequency-dependent, complex transfer function. An analytical determination of the dynamic response is presented and validated.

Microphones are widely applied to measure pressure fluctuations at the walls of solid bodies immersed in turbulent flows. Turbulent motions with various ...

Hand Controlled Manipulation of Single Molecules via a Scanning Probe Microscope with a 3D Virtual Reality Interface

Considering organic molecules as the functional building blocks of future nanoscale technology, the question of how to arrange and assemble such building blocks in a bottom-up approach is still open. The scanning probe microscope (SPM) could be a tool of choice; however, SPM-based manipulation was until recently limited to two dimensions (2D). Binding the SPM tip to a molecule at a well-defined position opens an opportunity of controlled manipulation in 3D space. Unfortunately, 3D manipulation is largely incompatible with the typical 2D-paradigm of viewing and generating SPM data on a computer. For intuitive and efficient manipulation we therefore couple a low-temperature non-contact atomic force/scanning tunneling microscope (LT NC-AFM/STM) to a motion capture system and fully immersive virtual reality goggles. This setup permits &#34;hand controlled manipulation&#34; (HCM), in which the SPM tip is moved according to the motion of the experimenter&#39;s hand, while the tip trajectories as well as the response of the SPM junction are visualized in 3D. HCM paves the way to the development of complex manipulation protocols, potentially leading to a better fundamental understanding of nanoscale interactions acting between molecules on surfaces. Here we describe the setup and the steps needed to achieve successful hand-controlled molecular manipulation within the virtual reality environment.

We demonstrate the precise manipulation of individual organic molecules on a metal surface with the tip of a scanning probe microscope driven in 3D by the experimenter's hand using a motion capture system and fully immersive virtual reality goggles.

Considering organic molecules as the functional building blocks of future nanoscale technology, the question of how to arrange and assemble such building ...

Standardized Method for Measuring Collection Efficiency from Wipe-sampling of Trace Explosives

One of the limiting steps to detecting traces of explosives at screening venues is effective collection of the sample. Wipe-sampling is the most common procedure for collecting traces of explosives, and standardized measurements of collection efficiency are needed to evaluate and optimize sampling protocols. The approach described here is designed to provide this measurement infrastructure, and controls most of the factors known to be relevant to wipe-sampling. Three critical factors (the applied force, travel distance, and travel speed) are controlled using an automated device. Test surfaces are chosen based on similarity to the screening environment, and the wipes can be made from any material considered for use in wipe-sampling. Particle samples of the explosive 1,3,5-trinitroperhydro-1,3,5-triazine (RDX) are applied in a fixed location on the surface using a dry-transfer technique. The particle samples, recently developed to simulate residues made after handling explosives, are produced by inkjet printing of RDX solutions onto polytetrafluoroethylene (PTFE) substrates. Collection efficiency is measured by extracting collected explosive from the wipe, and then related to critical sampling factors and the selection of wipe material and test surface. These measurements are meant to guide the development of sampling protocols at screening venues, where speed and throughput are primary considerations.

Optimized sampling protocols and the development of new wipe materials can be facilitated by standardized measurements of collection efficiency from wipe-sampling. Our approach for sampling trace explosives uses an automated device to control speed, force, and distance during wipe-sampling followed by extraction of collected explosives.

One of the limiting steps to detecting traces of explosives at screening venues is effective collection of the sample. Wipe-sampling is the most common ...

Generation of Size-controlled Poly (ethylene Glycol) Diacrylate Droplets via Semi-3-Dimensional Flow Focusing Microfluidic Devices

Uniform and size-controllable poly (ethylene glycol) diacrylate (PEGDA) droplets could be produced via the flow focusing process in a microfluidic device. This paper proposes a semi-three-dimensional (semi-3D) flow-focusing microfluidic chip for droplet formation. The polydimethylsiloxane (PDMS) chip was fabricated using the multi-layer soft lithography method. Hexadecane containing surfactant was used as the continuous phase, and PEGDA with the ultraviolet (UV) photo-initiator was the dispersed phase. Surfactants allowed the local surface tension to drop and formed a more cusped tip which promoted breaking into tiny micro-droplets. As the pressure of dispersed phase was constant, the size of droplets became smaller with increasing continuous phase pressure before dispersed phase flow was broken off. As a result, droplets with size variation from 1 &#181;m to 80 &#181;m in diameter could be selectively achieved by changing the pressure ratio in two inlet channels, and the average coefficient of variation was estimated to be below 7%. Furthermore, droplets could turn into micro-beads by UV exposure for photo-polymerization. Conjugating biomolecules on such micro-beads surface have many potential applications in the fields of biology and chemistry.

Generation of Size-controlled Poly ethylene Glycol Diacrylate Droplets via Semi-3-Dimensional Flow Focusing Microfluidic Devices

Here, we present a protocol to illustrate the fabrication processes and verifying experiments of a semi-three-dimensional (semi-3D) flow-focusing microfluidic chip for droplet formation.

Uniform and size-controllable poly (ethylene glycol) diacrylate (PEGDA) droplets could be produced via the flow focusing process in a microfluidic device. ...

Construction and Operation of a Light-driven Gold Nanorod Rotary Motor System

The possibility to generate and measure rotation and torque at the nanoscale is of fundamental interest to the study and application of biological and artificial nanomotors and may provide new routes towards single cell analysis, studies of non-equilibrium thermodynamics, and mechanical actuation of nanoscale systems. A facile way to drive rotation is to use focused circularly polarized laser light in optical tweezers. Using this approach, metallic nanoparticles can be operated as highly efficient scattering-driven rotary motors spinning at unprecedented rotation frequencies in water.
In this protocol, we outline the construction and operation of circularly-polarized optical tweezers for nanoparticle rotation and describe the instrumentation needed for recording the Brownian dynamics and Rayleigh scattering of the trapped particle. The rotational motion and the scattering spectra provides independent information on the properties of the nanoparticle and its immediate environment. The experimental platform has proven useful as a nanoscopic gauge of viscosity and local temperature, for tracking morphological changes of nanorods and molecular coatings, and as a transducer and probe of photothermal and thermodynamic processes.

Plasmonic gold nanorods can be trapped in liquids and rotated at kHz frequencies using circularly-polarized optical tweezers. Introducing tools for Brownian dynamics analysis and light scatteringspectroscopy leads to a powerful system for research and application in numerous fields of science.

The possibility to generate and measure rotation and torque at the nanoscale is of fundamental interest to the study and application of biological and ...

Fabrication of Soft Pneumatic Network Actuators with Oblique Chambers

Soft pneumatic network actuators have become one of the most promising actuation devices in soft robotics which benefits from their large bending deformation and low input. However, their monotonous bending motion form in two-dimensional (2-D) space keeps them away from wide applications. This paper presents a detailed fabrication method of soft pneumatic network actuators with oblique chambers, to explore their motions in three-dimensional (3-D) space. The design of oblique chambers enables actuators with tunable coupled bending and twisting capabilities, which gives them the possibility to move dexterously in flexible manipulators, to become biologically inspired robots and medical devices. The fabrication process is based on the molding method, including the silicone elastomer preparation, chamber and base parts fabrication, actuator assembly, tubing connections, checks for leaks, and actuator repair. The fabrication method guarantees the rapid manufacturing of a series of actuators with only a few modifications in the molds. The test results show the high quality of the actuators and their prominent bending and twisting capabilities. Experiments of the gripper demonstrate the advantages of the development in adapting to objects with different diameters and providing sufficient friction.

Here we present a fabrication method of soft pneumatic network actuators with oblique chambers. The actuators are capable of generating coupled bending and twisting motions, which broadens their application in soft robotics.