We thank Dr. Enken Drecoll for histological discussions and the extremely helpful team at Excillum AB, Sweden. We acknowledge financial support through the DFG Cluster of Excellence Munich Center for Advanced Photonics (MAP) and the DFG Gottfried Wilhelm Leibniz Program. Furthermore, this research project has received funding from the European&#8217;s Union Horizon 2020 research and innovation program under the Marie Sk&#322;odowska-Curie Grant Agreement No. H2020-MSCA-IF-2015-703745-CONSALT.

Caution: Please consult all relevant material safety data sheets (MSDS) before use. Several of the chemicals used in the protocol are acutely toxic and carcinogenic. Please use all appropriate safety practices when performing the staining protocol including the use of engineering controls (fume hood, glovebox) and personal protective equipment (safety glasses, gloves, lab coat, full length pants, closed-toe shoes).
Animals Used: 
Animal housing was carried out at the Klinikum rechts der Isar, Technical University of Munich in accordance with the European Union guidelines 2010/63. Organ removal was approved from an internal animal protection committee of Klinikum rechts der Isar, Munich, Germany (internal reference number 4-005-09). All procedures were in accordance with relevant guidelines and regulations. All laboratories are inspected for accordance with the OECD principles of good laboratory practice.
1. Eosin staining protocol
<ol>
	<li>To fixate soft-tissue samples, fill a 50-mL centrifuge tube with a fixative solution containing 9.5 mL of 4% (v/v) formaldehyde solution (FA) and 0.5 mL of glacial acetic acid (AA). 
	NOTE: Prepare the FA solution freshly from a 37% acid free FA solution stabilized with approximate 10% methanol. Dilute the FA solution further with Dulbecco&#8217;s phosphate buffered saline (DPBS). Choose DPBS without calcium and magnesium. Keep the dilute FA solution no longer than one month. During acidification the pH of the fixative solution is changing from neutral to approximately 3. 
	CAUTION: Because FA is acute organ toxic, corrosive and carcinogenic, the use of a fume hood is mandatory and appropriate protective personal equipment must be used.
	<ol>
		<li>Add the freshly removed soft-tissue sample to a 50-mL centrifuge tube and refrigerate the 50-mL centrifuge tube for 24-72h. 
		NOTE: The protocol can be paused here.</li>
		<li>Wash the soft-tissue sample with DPBS solution for 1h.</li>
	</ol>
	</li>
	<li>To stain the fixated soft-tissue sample (e.g., a whole mouse kidney), place the soft-tissue in 2 mL of eosin Y-staining solution and incubate the sample for 24 h. Keep the sample on a horizontal shaking plate for a smooth rocking (ca. 60 rpm) during the incubation process. 
	NOTE: The eosin Y-staining solution has a concentration of 30% (w/v) in distilled water. Choose the volume of the staining solution in such a way that the sample is completely covered by the staining solution and allow the sample to move freely within the sample container. The incubation time may differ for other samples and has to be adjusted accordingly.</li>
	<li>After staining, remove the soft-tissue sample carefully from the sample container.
	<ol>
		<li>Carefully remove excess of staining agent with cellulose tissue paper.</li>
		<li>Place the soft-tissue sample in a conical sample container above an ethanol vapor phase for storage and further use. 
		NOTE: The conical sample container must always contain a few drops of 70% (v/v) ethanol at the bottom of the tube to keep the soft-tissue sample moist and prevent artifacts.</li>
	</ol>
	</li>
</ol>
2. X-ray microCT imaging
NOTE: The X-ray microCT measurements were performed with a microCT scanner, which offers overview CT measurements (the ability to image the entire sample within the field of view (FOV)) and the performance of high-resolution CT measurements (the ability to focus in on one desired volume of interest (VOI) of the very same sample) down to 1 &#181;m.
<ol>
	<li>Mount the soft-tissue sample to an appropriate sample holder. Ensure a tight fit of the sample on the sample holder to prevent the sample from moving during the X-ray CT measurements.
	<ol>
		<li>In case of the stained mouse kidney: Prepare a sample holder with two centrifuge tubes, whereby the bottom of one tube is cut off. Glue the two centrifuge tubes together using two-component adhesive. Ensure a straight alignment of the centrifuge tubes around the rotation axis. Wait for the adhesive to harden.</li>
		<li>Once the sample holder is ready for use, transfer the mouse kidney into the intact centrifuge tube, which holds a few drops of 70% (v/v) ethanol at the bottom of the tube. 
		NOTE: Stability of the sample is crucial. Take time to prepare the sample for X-ray CT measurements. The soft-tissue sample is kept over an ethanol vapor phase to keep the sample moist during the X-ray CT measurements and prevent the soft-tissue sample from shrinkage and other artifacts. The soft-tissue sample should not be in contact with the solvent to obviate accumulation of the solvent around the sample during X-ray CT measurement, which might lead to sample movement during the measurement or might cause problems during reconstruction. If the sample holder does not allow to hold solvent at the bottom, a cellulose paper moistened with 70% (v/v) ethanol can be placed in the sample holder. It should be noted that shrinkage artifacts due to the solvent ethanol were not observed. 
		NOTE: The protocol can be paused here.</li>
	</ol>
	</li>
	<li>After careful alignment of the sample, choose acquisition parameters for best image quality. In case of the presented microCT data, acquire the scan at a peak voltage of 50 kV, a current of 3.5 W using 1601 projections equally distributed over 360&#176;. 
	NOTE: The acquisition parameters for the overview CT scan were chosen for best image quality. As such the 0.39x camera objective was chosen to cover the whole sample within the field of view (FOV). This resulted in an effective pixel size of 12 &#181;m. The exposure time of 2 s per projection provided a good signal to noise ratio. The ROI for the high-resolution CT scan was identified using the microCT data from the overview scan. MicroCT scanners often incorporate an integrated software tool, which allows for the precise selection of the determined ROI. For the high-resolution CT data, the 4x camera objective was chosen resulting in an effective pixel size of 3.3 &#181;m. Here, an exposure time of 15 s per projection was needed. 
	NOTE: The protocol can be paused here.</li>
	<li>After acquisition of the X-ray CT data, process the projections accordingly for reconstruction of the 3D volume. In case of the presented microCT data: Reconstruct the X-ray CT data with the integrated software. 
	NOTE: The volume renderings of the microCT data shown in Figure 1 and Figure 2 were generated using a visualization software. 
	NOTE: The protocol can be paused here.</li>
</ol>
3. X-ray nanoCT imaging
NOTE: The X-ray nanoCT scanner has been developed inhouse. The lens free instrument is equipped with a nanofocus X-ray source and a single-photon counting detector. 3D data with resolutions down to 100 nm can be generated10. Generally, nanoCT systems including those with X-ray optics are commercially available and not limited to the described nanoCT scanner.
<ol>
	<li>NanoCT sample preparation
	<ol>
		<li>Prepare VOIs of the soft-tissue sample. Cut the soft tissue into very small pieces of approximately 0.5 mm edge length using a scalpel and a stereomicroscope. In case of the mouse kidney: Cut the mouse kidney into two halves along the longest axis. Take one half of the mouse kidney and prepare different anatomical regions such as renal cortex and renal medulla. 
		NOTE: The other halve of the mouse kidney was transferred to histopathology, where the sample was embedded into paraffin and processed accordingly to yield the typical histological sections as seen in Figure 3c and Figure 3d.</li>
		<li>Transfer the small pieces before the first dehydration step to a new Petri dish, where they remain for all subsequent steps.</li>
		<li>Dehydrate the samples using concentrations (all v/v) in %: 50, 60, 70, 80, 90, 96 and 100 ethanol balanced with distilled water. Perform each dehydration step for 1 h each. 
		NOTE: The protocol can be paused here. Keep the small tissue pieces in 100% ethanol overnight.</li>
		<li>Critical point dry (CPD) the small tissue pieces. 
		NOTE: The application of CPD enables the complete dehydration of the tissue sample by exchanging the solvent (here ethanol) with the drying agent (here CO2). This has been necessary to ensure that the sample can be mounted to the sample holders of the nanoCT, is not moving during the measurement and can be positioned very close to the X-ray source to allow for best geometrical magnification. The nanoCT setup is based on mere geometrical magnification, with the magnification factor being defined as the source-to-detector distance over the source-to-sample distance. The drying technique was first introduced by Anderson to preserve the 3D structure of biological specimens for electron microscopy28. An overview of the technique is provided by Bray29.
		<ol>
			<li>Prefill the vacuum chamber with 100% ethanol. Transfer the small tissue pieces into a micro-porous capsule and place it in the vacuum chamber of the CPD. Close the system. 
			NOTE: Since high pressure is involved in the CPD process, ensure all parts of the CPD, in particular the fittings, are intact and the system is properly closed.</li>
			<li>Cool the chamber to 6- 8&#176;C and fill up with liquid CO2.</li>
			<li>While stirring, wait 3 min to allow for proper mixing of the two components. Carefully drain the chamber. Ensure the sample holder is still covered with solvent. Repeat this step ten times to allow complete replacement of ethanol with CO2 within the sample.</li>
			<li>After the final filling of the chamber with CO2, heat the machine to the critical point of CO2 (31 &#176;C and 73.8bar) followed by very slow release of the gaseous CO2 over a time of 30 min. 
			NOTE: The release of the gas should be undertaken very slowly as otherwise condense water can form on the sample. Ensure that the temperature does not drop below the critical point of CO2. Only open the CPD machine when all pressure has been released from the system.</li>
			<li>Remove the CPD tissue pieces quickly from the machine and keep them in a new Petri dish stored in a desiccator prior to further use. 
			NOTE: The protocol can be paused here.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Mount the CPD tissue pieces to an appropriate sample holder. Ensure a tight fit of the sample on the sample holder to prevent the sample from moving during the CT measurements. In case of the CPD mouse kidney tissue pieces: Glue the tissue pieces with superglue to a sample holder. 
	NOTE: Any undesired movement of the sample during CT measurements can cause problems during volume reconstruction - especially when acquiring a data set with nanometer voxel size. 
	NOTE: The protocol can be paused here.</li>
	<li>After careful alignment of the sample, choose acquisition parameters for best image quality. In case of the presented nanoCT data: Acquire projections at a peak voltage of 60 kV with 1599 projections equally distributed over 360&#176; and a voxel size of approximately 400 nm. 
	NOTE: A single CT measurement acquired at 400 nm voxel size has a FOV of 75 &#181;m in the direction of the rotation axis (vertical) and approximately 560 &#181;m in the direction perpendicular to the rotation axis (horizontal). To investigate larger volumes, an extension of the FOV along the rotation axis can be achieved by combining multiple scans at different vertical positions. Additionally, local tomography scans can be performed to measure samples with a larger sample diameter perpendicular to the rotation axis than given by the FOV of a global CT scan. The nanoCT data was acquired with an exposure time of 4 s per projection. As such the total acquisition time per data set was approximately 3.5 h. 
	NOTE: The protocol can be paused here.</li>
	<li>After acquisition of the CT data, process the projections accordingly for reconstruction of the 3D volume.
	<ol>
		<li>In case of the presented nanoCT data, normalize the acquired projections with flatfield images. Enhance the sharpness of the projections by using a Richardson-Lucy deconvolution algorithm30,31. Use a rotationally symmetric Gaussian function with a standard deviation of one pixel as deconvolution kernel.</li>
		<li>Apply Paganin&#8217;s phase-retrieval algorithm to the sharpened images to increase the soft-tissue contrast. Set the parameters of the algorithm to optimize the image quality32. Reconstruct the preprocessed projections with a state-of-the-art filtered backprojection algorithm. 
		NOTE: Figure 3 evaluates the obtained nanoCT data with corresponding histological sections, which were approximately 7 &#181;m thick. Therefore, minimum intensity projection slices of 18 adjacent nanoCT slices with a virtual thickness of approximately 7 &#181;m were generated by means of calculating the minimum value for each pixel in the relevant slices. A visualization software was used to render the volume of the nanoCT data, which is displayed in Figure 4.</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Suvarna, S. K., Layton, C., Bancroft, J. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Theory and Practice of Histological Techniques. 7th edn. , (2013).</li><li>Chatterjee, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Artefacts+in+histopathology.">Artefacts in histopathology.</a> Journal of Oral and Maxillofacial Pathology. 18 (4), 111-116 (2014).</li><li>McInnes, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Artefacts+in+histopathology.">Artefacts in histopathology.</a> Comparative Clinical Pathology. 13 (3), 100-108 (2005).</li><li>Andreasen, A., Drewes, A., Assentoft, J., Larsen, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Computer-assisted+alignment+of+standard+serial+sections+without+use+of+artificial+land-marks.+A+practical+approach+to+the+utilization+of+incomplete+information+in+3-d+reconstruction+of+the+hippocampal+region.">Computer-assisted alignment of standard serial sections without use of artificial land-marks. A practical approach to the utilization of incomplete information in 3-d reconstruction of the hippocampal region.</a> Journal of Neuroscience Methods. 45 (3), 199-207 (1992).</li><li>Braverman, M. S., Braverman, I. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Three-dimensional+reconstructions+of+objects+from+serial+sections+using+a+microcomputer+graphics+system.">Three-dimensional reconstructions of objects from serial sections using a microcomputer graphics system.</a> Journal of Investigative Dermatology. 86 (3), 290-294 (1986).</li><li>Denk, W., Hortsmann, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Serial+block-face+scanning+electron+microscopy+to+reconstruct+three-dimensional+tissue+nanostructure.">Serial block-face scanning electron microscopy to reconstruct three-dimensional tissue nanostructure.</a> PLoS Biology. 2 (11), 329 (2004).</li><li>Mohun, T. J., Weninger, J. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Imaging+heart+development+using+high-resolution+episcopic+microscopy.">Imaging heart development using high-resolution episcopic microscopy.</a> Current Opinion in Genetics and Development. 21, 573-578 (2011).</li><li>Weninger, J. W., Meng, S., Streicher, J., M&#252;ller, G. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+new+episcopic+method+for+rapid+3-d+reconstruction:+applications+in+anatomy+and+embryology.">A new episcopic method for rapid 3-d reconstruction: applications in anatomy and embryology.</a> Anatomy and Embryology. 197 (5), 341-348 (1998).</li><li>Odgaard, A., Andersen, K., Melsen, F., Gundersen, H. J. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Direct+Method+for+Fast+3-Dimensional+Serial+Reconstruction.">A Direct Method for Fast 3-Dimensional Serial Reconstruction.</a> Journal of Microscopy. 159, 335-342 (1990).</li><li>M&#252;ller, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Myoanatomy+of+the+velevt+worm+leg+revealed+by+labratory-based+nanofocus+X-ray+source+tomography.">Myoanatomy of the velevt worm leg revealed by labratory-based nanofocus X-ray source tomography.</a> Proceedings of the National Academy of Sciences of the United States of America. 114 (47), 12378-12383 (2017).</li><li>Salomon, M., Hanke, R., Kr&#252;ger, P., Uhlmann, N., Voland, V. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Realization+of+a+computed+tomography+setup+to+achieve+resolutions+below+1+&#181;m.">Realization of a computed tomography setup to achieve resolutions below 1 &#181;m.</a> Nuclear Instruments and Methods in Physics Research Section A. 591, 50-53 (2008).</li><li>Tkachuk, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=X-ray+computed+tomography+in+Zernike+phase+contrast+mode+at+8+keV+with+50-nm+resolution+using+Cu+rotating+anode+X-ray+source.">X-ray computed tomography in Zernike phase contrast mode at 8 keV with 50-nm resolution using Cu rotating anode X-ray source.</a> Zeitschrift f&#252;r Kristallographie. 222, 650-655 (2007).</li><li>Withers, P. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=X-ray+nanotomography.">X-ray nanotomography.</a> Materials Today. 10, 26-34 (2007).</li><li>Jahn, H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evaluation+of+contrasting+techniques+for+X-ray+imaging+of+velvet+worms+(Onychophora).">Evaluation of contrasting techniques for X-ray imaging of velvet worms (Onychophora).</a> Journal of Microscopy. 270 (3), 343-358 (2018).</li><li>Martins de S. e Silva, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Three-dimensional+non-destructive+soft-tissue+visualization+with+X-ray+staining+micro-tomography.">Three-dimensional non-destructive soft-tissue visualization with X-ray staining micro-tomography.</a> Scientific Reports. 5, 14088 (2015).</li><li>Metscher, B. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=MicroCT+for+Developmental+Biology:+A+Versatile+Tool+for+High-Contrast+3D+Imaging+at+Histological+Resolutions.">MicroCT for Developmental Biology: A Versatile Tool for High-Contrast 3D Imaging at Histological Resolutions.</a> Developmental Dynamics. 238, 632-640 (2009).</li><li>Metscher, B. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=MicroCT+for+comparative+morphology:+simple+staining+methods+allow+high-contrast+3D+imaging+of+diverse+non-mineralized+animal+tissues.">MicroCT for comparative morphology: simple staining methods allow high-contrast 3D imaging of diverse non-mineralized animal tissues.</a> BMC Physiology. 9, 11 (2009).</li><li>Mitzutani, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=X-Ray+Microtomographic+Imaging+of+Three-Dimensional+Structure+of+Soft+Tissues.">X-Ray Microtomographic Imaging of Three-Dimensional Structure of Soft Tissues.</a> Tissue Engineering Part C: Methods. 14 (4), 359-363 (2008).</li><li>Pauwels, E., Loo, D. v., Cornillie, P., Brabant, L., Hoorebeke, L. v. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+exploratory+study+of+contrast+agents+for+soft+tissue+visualization+by+means+of+high+resolution+X-ray+computed+tomography+imaging.">An exploratory study of contrast agents for soft tissue visualization by means of high resolution X-ray computed tomography imaging.</a> Journal of Microscopy. 250, 21-31 (2013).</li><li>Degenhardt, K., Wright, A. C., Horng, D., Padmanabhan, A., Epstein, J. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Rapid+3D+phenotyping+of+cardiovascular+development+in+mouse+embryos+by+micro-CT+with+iodine+staining.">Rapid 3D phenotyping of cardiovascular development in mouse embryos by micro-CT with iodine staining.</a> Circulation: Cardiovascular Imaging. 3 (3), 314-322 (2010).</li><li>Dullin, C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=&#956;CT+of+ex-vivo+stained+mouse+hearts+and+embryos+enables+a+precise+match+between+3D+virtual+histology,+classical+histology+and+immunochemistry.">&#956;CT of ex-vivo stained mouse hearts and embryos enables a precise match between 3D virtual histology, classical histology and immunochemistry.</a> PLOS ONE. 12 (2), 0170597 (2017).</li><li>Jeffrey, N. S., Stephenson, R. S., Gallagher, J. A., Cox, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Micro-computed+tomography+with+iodine+staining+resolves+the+arrangement+of+muscle+fibres.">Micro-computed tomography with iodine staining resolves the arrangement of muscle fibres.</a> Journal of Biomechanics. 44, 189-192 (2011).</li><li>Johnson, J. T., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Virtual+Histology+of+Transgenic+Mouse+Embryos+for+High-Throughput+Phenotyping.">Virtual Histology of Transgenic Mouse Embryos for High-Throughput Phenotyping.</a> PLOS Genetics. 2, 61 (2006).</li><li>Leszczy&#324;ski, B., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Visualization+and+Quantitative+3D+Analysis+of+Intraocular+Melanoma+and+Its+Vascularization+in+a+Hamster+Eye.">Visualization and Quantitative 3D Analysis of Intraocular Melanoma and Its Vascularization in a Hamster Eye.</a> International Journal of Molecular Sciences. 19 (2), 332 (2018).</li><li>Mizutani, R., Suzuki, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=X-ray+microtomography+in+biology.">X-ray microtomography in biology.</a> Mircon. 43, 104-115 (2012).</li><li>Busse, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Three-dimensional+virtual+histology+enabled+through+cytoplasm-specific+X-ray+stain+for+microscopic+and+nanoscopic+computed+tomography.">Three-dimensional virtual histology enabled through cytoplasm-specific X-ray stain for microscopic and nanoscopic computed tomography.</a> Proceedings of the National Academy of Sciences of the United States of America. 115 (10), 2293-2298 (2018).</li><li>M&#252;ller, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Non-destructive+high-resolution+3D+virtual+histology+enabled+through+a+cell+nucleus-specific+stain+for+X-ray+computed+tomography.">Non-destructive high-resolution 3D virtual histology enabled through a cell nucleus-specific stain for X-ray computed tomography.</a> Scientific Reports. 8, 17855 (2018).</li><li>. ZEISS product information: ZEISS Xradia 510 Versa Available from: <a target="_blank" href="https://www.zeiss.com/microscopy/int/products/x-ray-microscopy/zeiss-xradia-510-versa.html">https://www.zeiss.com/microscopy/int/products/x-ray-microscopy/zeiss-xradia-510-versa.html</a> (2019)</li><li>Nachtrab, F., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Development+of+a+Timepix+based+detector+for+the+NanoXCT+project.">Development of a Timepix based detector for the NanoXCT project.</a> Journal of Instrumentation. 10 (11), 11009 (2015).</li><li>Kraft, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Performance+of+single-photon-counting+PILATUS+detector+modules.">Performance of single-photon-counting PILATUS detector modules.</a> Journal of Synchrotron Radiation. 16 (3), 368-375 (2009).</li><li>Kraft, P., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Characterization+and+calibration+of+PILATUS+detectors.">Characterization and calibration of PILATUS detectors.</a> IEEE Transactions on Nuclear Science. 56 (3), 758-764 (2009).</li><li>. ZEISS product information: ZEISS Xradia 810 Ultra Available from: <a target="_blank" href="https://www.zeiss.com/microscopy/int/products/x-ray-microscopy/zeiss-xradia-510-versa.html">https://www.zeiss.com/microscopy/int/products/x-ray-microscopy/zeiss-xradia-510-versa.html</a> (2019)</li><li>Anderson, T. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Techniques+for+the+preservation+of+three-dimensional+structure+in+preparing+specimens+for+the+electron+microscope.">Techniques for the preservation of three-dimensional structure in preparing specimens for the electron microscope.</a> Transactions of the New York Academy of Sciences. 13 (4), 130-134 (1951).</li><li>Bray, D., Williams, J. R., Clifford, A. A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Supercritical Fluid Methods and Protocols. Methods in Biotechnology. 13, 235-243 (2000).</li><li>Lucy, L. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+iterative+technique+for+the+rectification+of+observed+distributions.">An iterative technique for the rectification of observed distributions.</a> The Astronomical Journal. 79, 745-765 (1974).</li><li>Richardson, W. H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Bayesian-Based+Iterative+Method+of+Image+Restoration.">Bayesian-Based Iterative Method of Image Restoration.</a> The Journal of the Optical Society of America. 62 (1), 55-59 (1972).</li><li>Paganin, F., Mayo, S. C., Gureyev, T. E., Miller, P. R., Wilkins, S. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Simultaneous+phase+and+amplitude+extraction+from+a+single+defocused+image+of+a+homogeneous+object.">Simultaneous phase and amplitude extraction from a single defocused image of a homogeneous object.</a> Journal of Microscopy. 206, 33-40 (2002).</li><li>Riedelsheimer, B., B&#252;chl-Zimmermann, S., Mulisch, M., Welsch, U. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Mikroskopische Technik. , 193-194 (2015).</li><li>Hubbell, J. H., Seltzer, S. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tables+of+Xray+mass+attenuation+coefficients+and+mass+energy-absorption+coefficients+from+1+keV+to+92+keV+and+48+additional+substances+of+dosimetric+interest,+Table+3.">Tables of Xray mass attenuation coefficients and mass energy-absorption coefficients from 1 keV to 92 keV and 48 additional substances of dosimetric interest, Table 3.</a> National Institute of Standards and Technology. , (1995).</li><li>Hong, H. Y., Yoo, G. S., Choi, J. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+Eosin+Y+Method+for+Protein+Determination+in+Solution.">An Eosin Y Method for Protein Determination in Solution.</a> Analytical Letters. 32 (12), 2427-2442 (1999).</li><li>. GE product information: Phoenix nanotom m Available from: <a target="_blank" href="https://www.gemeasurement.com/sites/gemc.dev/files/geit-31344en_nanotom_m_0517.pdf">https://www.gemeasurement.com/sites/gemc.dev/files/geit-31344en_nanotom_m_0517.pdf</a> (2019)</li><li>Dierick, M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Recent+Micro-CT+Scanner+Developments+at+UGCT.">Recent Micro-CT Scanner Developments at UGCT.</a> Nuclear Instruments and Methods in Physics Research Section B. 324, 35-40 (2014).</li><li>Kastner, J., Plank, B., Heinzl, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Advanced+X+computed+tomography+methods:+High+resolution+CT,+quantitative+CT,+4DCT+and+phase+contrast+CT.">Advanced X computed tomography methods: High resolution CT, quantitative CT, 4DCT and phase contrast CT.</a> Proceedings of Digital Industrial Radiology and Computed Tomography. , 120-132 (2015).</li></ol>

The authors have nothing to disclose.

Currently, eosin is used as the standard histological protocol to label the cell cytoplasm. The staining agent is applied as a 0.1% (w/v) aqueous solution to microscopic slices of soft tissue (generally cut with a thickness of 2-10 &#181;m)33. The application of this standardized histological protocol to 3D tissue samples such as a whole mouse kidney does not result in an attenuation contrast enhanced CT image. On the one hand, this can be attributed to the low intrinsic attenuation properties of soft tissue for typically used X-ray energies of laboratory-based microCT systems. Usually, soft tissue is composed of mainly carbon, hydrogen, oxygen and nitrogen34, and therefore, does not result in contrast enhancement. On the other hand, the low concentration of eosin used for staining was the limiting factor. Even though one eosin molecule holds four bromide atoms (high atomic number element bromine with Z = 3534), the sensitivity levels required for X-ray CT imaging were not met.
To overcome this challenge of low attenuation contrast, several concentrations of eosin were investigated. A limitation is here the maximum solubility of eosin in water, which is 30% (w/v) in an aqueous solution. Best attenuation contrast enhancement within the soft tissue was observed with the highest eosin concentration, which was expected according to the Lambert-Beer Law. Therefore, the final staining protocol was carried out with the highest concentration.
The question how to prepare the soft tissue optimally on a molecular level for the staining procedure to further improve contrast enhancement was answered by pH adjustment. Here, the acidification of the soft-tissue sample during fixation or before staining was found to be crucial. This was also shown by Hong et al.35. The higher accumulation of staining agent within the cell cytoplasm by the acid was achieved through improved ionic interactions, which were a result of the protonation of amino acid side chains of proteins and peptides present within the cell cytoplasm. A representative result highlighting the contrast enhancement in comparison to an unstained soft-tissue sample is shown in Figure 1a,b. Here, a structural overview of a whole mouse kidney visualizing crucial anatomical regions such as cortex, medulla, papilla and renal pelvis was achieved.
The presented staining protocol is simple to apply and contains only three steps. The required reagents are easily accessible. The overall staining time of 24 hours is fast for a whole-organ staining, which enables the 3D visualization of soft-tissue samples (Figure 1c, Figure 2b and Figure 4b) in a laboratory environment at multiple scales down to cellular level. It should be noted that the overall staining time and volume of the staining solution needed might request some adaptations depending on the nature of the sample. Nevertheless, the eosin-based staining protocol is suitable for whole-organ staining, which then enables high-resolution microCT imaging of whole organs. Shrinkage artifacts due to the solvent ethanol, which was used to keep the sample moist during the microCT measurements, were not observed. Additional preparation steps are required for nanoCT imaging, which allows for the investigation of smaller tissue pieces retrieved from the original sample. With respect to future histopathological applications, the overview scans will provide valuable insights into altered anatomical regions and structures, which allow for the determination of ROIs as demonstrated in Figure 2a. Those can be studied in 3D by microCT (Figure 1c and Figure 2b) or nanoCT (Figure 4b) and evaluated in 2D with histology (Figure 3).
Another strength of the protocol is seen in the full compatibility with histopathology with respect to the H&#38;E staining procedure. The application of the eosin-based staining procedure to bulk samples does not impede further histological investigations (Figure 3), even though the applied eosin concentration is much higher compared to the histological staining solution. The nanoCT slice with a virtual thickness of approximately 400 nm (Figure 3a) compares already very well with the histological section (Figure 3c), which was derived from the corresponding soft-tissue sample. Considering the approximate thickness of a histological section with 7-10 &#181;m, the generation of minimum intensity projection slices of the nanoCT data (Figure 3b), which correspond to a virtual thickness of approximately 7 &#181;m, allows for a better comparison with the histological section (Figure 3c). Here, the cell nuclei are clearly revealed as non-attenuation area as eosin specifically stains proteins and peptides in the cell cytoplasm33.
The application of further counter staining with standard histological methods is possible, even though the order of the staining compared to the standard histological staining procedure was reversed. Starting first with the developed eosin-based staining protocol for CT, followed by counter staining of those eosin-based histological sections with hematoxylin, allows for full compatibility and results in a high-quality staining displaying the expected form of appearance. The cell nuclei-specific staining with Mayer&#8217;s sour hematoxylin was applied to the histological section highlighting the cell nuclei in purple (Figure 3d). The application of histological counter staining is currently limited to the H-stain. Other standard histological counter stainings such as periodic acid Schiff&#8217;s base, Elastica van Gieson or Gomori silver have to be evaluated as well as the compatibility with immunohistological techniques needs to be tested.
The eosin-based staining protocol allows for (i) cell cytoplasm-specific targeting, (ii) homogenous and complete staining, (iii) easy implementation, (iv) fast penetration of the tissue without creating artifacts such as diffusion rings, (v) the staining of large and dense soft-tissue samples, and (vi) full compatibility with histopathology in respect of the H&#38;E stain. These requirements are important to allow high-resolution X-ray CT visualization of soft tissue down to cellular level. In combination with the recently developed nanoCT devices12,36,37, nondestructive generation of virtual histological slices that are comparable in contrast and resolution to conventional histological data is rendered possible. This combined approach will enable the establishment of X-ray CT as a valuable tool for the 3D visualization of microscopic tissue structures.

Full characterization of soft-tissue specimens requires information about the 3D tissue microstructure. The current gold standard for soft-tissue sample analyses is histopathology. The tissue and cellular morphology of the specimen are explored in 2D within selected regions of interest (ROIs) using optical microscopy1. This method, however, has several drawbacks. The preparation of the sample is time-consuming, complicated, destructive and prone to artifacts. The produced microscopic slides provide only 2D information parallel to the sectioning plane. Often the number of histological sections, which are investigated, is restricted due to time constraints2,3.
In recent years, the field of 3D histology has evolved. Here, virtual tissue slices from any desired spatial plane are accessible. This allows for the tracking of structures throughout the sample, which leads to a deeper understanding of the 3D tissue architecture and structural changes associated with different pathologies. Various methods have been developed to achieve the generation of 3D volume data. They range from serial-section based approaches, which use either light or electron microscopy4,5,6,7,8, to block-face imaging methods, such as episcopic 3D imaging or block-face scanning electron microscopy7,8,9. All the mentioned methods, however, involve either sectioning or destruct the sample completely, which does not allow for further investigations. The obtained resolution is highly dependent on the sectioning process being prone to artifacts as described in conventional histology. These methods suffer also from alignment artifacts.
3D X-ray imaging techniques such as microscopic and nanoscopic computed tomography (microCT and nanoCT) aspire to generate 3D high-resolution data without destruction of the tissue sample. So far, the weak X-ray attenuation contrast of soft tissue and the limited access to high resolutions in a laboratory environment has impaired their use for 3D visualization of microscopic tissue structures. Recent advances towards laboratory-based, high-resolution X-ray CT allow for resolutions well below 1 &#181;m10,11,12,13.
The lack of contrast in soft tissue in conventional attenuation-based X-ray imaging is compensated by staining agents, which enhance the X-ray attenuation contrast. Staining agents known from other imaging techniques such as osmium tetroxide (OsO4), iodine potassium iodide (IKI) or phosphotungstic acid (PTA) are often used14,15,16,17,18,19,20,21,22,23,24,25. Staining agents that allow for (i) specific biological targeting, (ii) homogenous and complete staining, (iii) easy handling, (iv) fast penetration of the tissue without creating artifacts such as diffusion rings, (v) large and dense tissue staining, and (vi) full compatibility with histopathology are required to establish X-ray CT as tool for 3D visualization of microscopic tissue structures. In this work, we show how soft-tissue samples are prepared for X-ray CT imaging with a cytoplasm-specific X-ray stain based on eosin that fulfills the requirements stated above26.
The multiscale imaging approach ensures the assessment of staining quality through an overview microCT measurement and the selection of volumes of interest (VOIs) for further high-resolution investigations. Staining quality is analyzed focusing on staining parameters such as (i) completeness, (ii) appearance of diffusion rings, (iii) contrast enhancement, (iv) appearance of CT artifacts such as streaks and (v) homogeneity. The laboratory-based nanoCT setup, which uses geometric magnification to reach resolutions down to 100 nm, visualizes soft-tissue morphology on (sub)-cellular level10,27. A comparative analysis of the nanoCT slices with corresponding histological light microscopy images confirms the reproduction of tissue architecture with similar detail on a microscopic level in 2D, enabling histopathological characterization of the tissue sample. This detailed video protocol is intended to raise the awareness and to highlight the potential of this methodology as non-destructive 3D soft-tissue imaging tool being of interest to a wide scientific community such as zoologists, biologists and health professionals.

<table><tbody><tr><td>50-ml centrifuge tube by Falcon</td><td>VWR</td><td>734-0453</td><td></td></tr><tr><td>Formaldehyde solution, 37%</td><td>Carl Roth</td><td>CP10.2</td><td>acid-free, stabilized with ~10% MeOH</td></tr><tr><td>Glacial acetic acid</td><td>Alfa Aesar</td><td>36289.AP</td><td></td></tr><tr><td>Eosin Y disodium salt</td><td>Sigma-Aldrich</td><td>E4382</td><td>certified by Biological Stain Commission</td></tr><tr><td>Phosphate Buffered Saline (PBS)</td><td>Merck</td><td>L1825</td><td>Dulbecco&#039;s formualtion, w/o calcium and magnesium</td></tr><tr><td>Sample Tubes by Nalgene</td><td>Carl Roth</td><td>ATK5.1</td><td></td></tr><tr><td>Rocking Shaker ST5</td><td>CAT</td><td>60281-0000</td><td></td></tr><tr><td>Cellulose tissue paper</td><td>VWR</td><td>115-0600</td><td></td></tr><tr><td>Forceps, by USBECK Laborger&amp;auml;te</td><td>VWR</td><td>232-0096</td><td></td></tr><tr><td>Microcentrifuge tubes by Eppendorf</td><td>VWR</td><td>211-2120</td><td>safe-lock, 2.0 ml</td></tr><tr><td>Ethanol absolute by Baker Analyzed</td><td>VWR</td><td>80252500</td><td></td></tr><tr><td>Disposable safety scalpel by Aesculap</td><td>VWR&amp;nbsp;</td><td>AESCBA210</td><td></td></tr><tr><td>Petri dish by Sterilin</td><td>VWR</td><td>391-2019</td><td></td></tr><tr><td>Plastic pasteur pipette</td><td>Carl Roth</td><td>EA68.1</td><td>graduated, 1 ml</td></tr><tr><td>Desiccator by Duran</td><td>VWR</td><td>SCOT247826954</td><td></td></tr><tr><td>Silicone grease by Bayer</td><td>Sigma-Aldrich</td><td>85404</td><td>high-vacuum</td></tr><tr><td>Carbon dioxide cylinder with standpipe</td><td>Linde</td><td>3700113</td><td>10 kg, short</td></tr><tr><td>micro-porous treatment capsule</td><td>PLANO GmbH</td><td>4614</td><td>pore size 78 &amp;micro;m (B)</td></tr><tr><td>Bal-Tec CPD 030</td><td>Bal-Tec AG</td><td></td><td>CO&lt;sub&gt;2&lt;/sub&gt; as drying agent</td></tr><tr><td>Stemi 2000-C stereomicroscope with KL 1500 LCD</td><td>Zeiss</td><td></td><td>this stereomicroscope has been updated&lt;sup&gt;(1)&lt;/sup&gt;</td></tr><tr><td>Zeiss Xradia Versa 500</td><td>Zeiss</td><td></td><td>this microCT scanner has been updated&lt;sup&gt;(2)&lt;/sup&gt;</td></tr><tr><td>Avizo Fire 8.1</td><td>Thermo Fisher Scientific</td><td></td><td></td></tr><tr><td>PILATUS detector as part of the nanoCT scanner</td><td>Dectris</td><td></td><td>single-photon counting detector&lt;sup&gt;(4,5)&lt;/sup&gt;; there are commercially availble nanoCT systems available &lt;sup&gt;(6,7)&lt;/sup&gt;</td></tr><tr><td>nanofocus X-ray source as part of the nanoCT scanner</td><td>Excillum</td><td></td><td>high-flux nanofocus X-ray transmission tube&lt;sup&gt;(3)&lt;/sup&gt;; there are commercially availble nanoCT systems available&lt;sup&gt;(6,7)&lt;/sup&gt;</td></tr><tr><td>(1) Germany, Z. ZEISS product information: ZEISS stereomicroscopes https://www.micro-shop.zeiss.com/de/de/system/Stereomikroskope/1006&gt; (September 06, 2019).</td><td></td><td></td><td></td></tr><tr><td>(2) Germany, Z. ZEISS product information: ZEISS Xradia 510 Versa https://www.zeiss.com/microscopy/int/products/x-ray-microscopy/zeiss-xradia-510-versa.html&gt; (April 10, 2019).</td><td></td><td></td><td></td></tr><tr><td>(3) Nachtrab, F. et al. Development of a Timepix based detector for the NanoXCT project. Journal of Instrumentation 10 (11), C11009, (2015).</td><td></td><td></td><td></td></tr><tr><td>(4) Kraft, P. et al. Performance of single-photon-counting PILATUS detector modules. Journal of Synchrotron Radiation 16 (3), 368-375, (2009).</td><td></td><td></td><td></td></tr><tr><td>(5) Kraft, P. et al. Characterization and calibration of PILATUS detectors. IEEE Transactions on Nuclear Science 56 (3), 758-764, (2009).</td><td></td><td></td><td></td></tr><tr><td>(6) Germany, Z. ZEISS product information: ZEISS Xradia 810 Ultra https://www.zeiss.com/microscopy/int/products/x-ray-microscopy/xradia-810-ultra.html&gt; (April 9 2019).</td><td></td><td></td><td></td></tr><tr><td>(7) Company, G. E. GE product information: Phoenix nanotom m, https://www.gemeasurement.com/sites/gemc.dev/files/geit-31344en_nanotom_m_0517.pdf&gt; (April 10, 2019).</td><td></td><td></td><td></td></tr></tbody></table>

3d imaging of soft-tissue samples using an x-ray specific staining method and nanoscopic computed tomography

We demonstrate a laboratory-based method combining X-ray microCT and nanoCT with a specific X-ray stain, which targets the cell cytoplasm. The described protocol is easy to apply, fast and suitable for larger soft-tissue samples. The presented methodology enables the characterization of crucial tissue structures in three dimensions and is demonstrated on a whole mouse kidney. The multiscale approach allows to image the entire mouse kidney and supports the selection of further volumes of interest, which are acquired with higher resolutions ranging into the nanometer range. Thereby, soft-tissue morphology with a similar detail level as the corresponding histological light microscopy images is reproduced. Deeper insights into the 3D configuration of tissue structures are achieved without impeding further investigations through histological methods.

Figure 1 shows CT slices and volume rendering of low-resolution microCT data highlighting contrast enhancement after staining. Figure 2 shows CT slices and volume rendering of high-resolution microCT data derived from a local tomography of the whole mouse kidney. Figure 3 shows CT slices of nanoCT data in comparison to the corresponding histological sections. Figure 4 shows CT slice and volume rendering of nanoCT data highlighting structural details at cellular level. The low-resolution microCT measurement allows for an overview of the whole organ and helps to identify volumes of interest (VOIs) for the high-resolution microCT measurement. Through this multiscale approach, the VOI for the nanoCT is determined. The nanoCT enables a very detailed view of the soft-tissue sample on cellular level. The comparative study with the corresponding histological section highlights full compatibility with histopathology. Here, the multimodal imaging approach is confirming the results obtained with both modalities.
<img alt="Figure 1" class="xfigimg" src="/files/ftp_upload/60251/60251fig1a.jpg" /> 
Figure 1. CT slices and volume rendering of the low-resolution microCT data.&#160;(a,b) Overview images of the same mouse kidney before and after staining, respectively, highlighting the contrast enhancement obtained after application of the eosin-based staining protocol. Both microCT data sets were acquired using identical acquisition parameters. The voxel size in both data sets is 12 &#181;m. The contrast enhancement achieved in (b) enables the identification of the following anatomic structural regions: Cortex (I), outer medulla (II) with further distinction in outer stripes of outer medulla (IIa) and inner stripes of outer medulla (IIb), inner medulla (III), papilla (IV) and renal pelvis (V). (c) Volume rendering of microCT data showing a virtual sagittal section through the whole mouse kidney. This figure has been modified from Busse and M&#252;ller et al.26 <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/60251/60251fig1alarge.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" class="xfigimg" src="/files/ftp_upload/60251/60251fig2a.jpg" /> 
Figure 2. CT slice and volume rendering of high-resolution microCT data derived from the same mouse kidney after application of the developed eosin-based staining protocol.&#160;(a) The left corner shows the overview microCT image highlighting the ROI (blue box) for the displayed high-resolution image. The following anatomic structural regions are identifiable: Cortex (I), outer medulla (II) with further distinction in outer stripes of outer medulla (IIa) and inner stripes of outer medulla (IIb), inner medulla (III), minor calyx (IV) and vessels (V and VI). (b) Volume of interest rendering of the high-resolution microCT data acquired with a voxel size of 3.3 &#181;m. The medulla region and a virtual section through a vessel derived from a local tomography of the whole kidney is shown. This figure has been modified from Busse and M&#252;ller et al.26. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/60251/60251fig2alarge.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" class="xfigimg" src="/files/ftp_upload/60251/60251fig3a.jpg" /> 
Figure 3. CT slices of nanoCT data (a,b) in comparison to the histological sections (c,d) derived from the same mouse kidney after application of the developed eosin-based staining protocol.&#160;(a) The nanoCT image of the same mouse kidney sample after staining, dissecting and CPD shows detailed structures of region (IIb) seen in Figure 1 and Figure 2. These are known as thick ascending limbs of the loop of Henle. (b) Minimum intensity projection slice derived from the same nanoCT data set shown in (a) with a virtual slice thickness of approximately 7 &#181;m, which allows for clear visualization of the cell nuclei. (c) Representative histological section displaying thick ascending limbs of the loop of Henle with clear visualization of cell nuclei and brush border. The histological section has an approximate thickness of 7 &#181;m and was obtained from the same mouse kidney sample after the applied eosin-based staining and embedding in a paraffin block. (d) Representative histological section with application of counter stain hematoxylin highlighting the cell nuclei in purple. Preparation of the histological section close to the section shown in (c) with approximate thickness of 7 &#181;m. This figure has been modified from Busse and M&#252;ller et al.26 <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/60251/60251fig3alarge.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 4" class="xfigimg" src="/files/ftp_upload/60251/60251fig4a.jpg" /> 
Figure 4. CT slice and volume rendering of nanoCT data.&#160;(a) The nanoCT image of the same mouse kidney sample showing the structures known as thick ascending limbs of the loop of Henle. This is a detailed view of region (IIb) seen in Figure 1 and Figure 2 acquired from a small piece of the kidney with a voxel size of approximately 400 nm. The preparation of the sample involved staining, dissecting and CPD. (b) Volume rendering of nanoCT data visualizing the 3D structure of thick ascending limbs of the loops of Henle. This figure has been modified from Busse and M&#252;ller et al.26 <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/60251/60251fig4alarge.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about 3D Imaging of Soft-Tissue Samples using an X-ray Specific Staining Method and Nanoscopic Computed Tomography at JoVE.com

3D Imaging of Soft-Tissue Samples using an X-ray Specific Staining Method and Nanoscopic Computed Tomography

A protocol for 3D visualization of microscopic tissue structures by using an X-ray specific staining method designed for X-ray computed tomography is presented.

We demonstrate a laboratory-based method combining X-ray microCT and nanoCT with a specific X-ray stain, which targets the cell cytoplasm. The described ...

3d-imaging-soft-tissue-samples-using-an-x-ray-specific-staining

Nanyang Technological University

Research

JoVE Journal

Bioengineering

9.7K Views.  Technical University of Munich. Ons nieuwe protocol stelt ons in staat om cellulaire structuren in 3D te visualiseren met behulp van x-ray computertomografie. En we doen dit door weefsel te bevlekken met eosine en op die manier het cytoplasma zichtbaar te maken. Naast medische toepassingen en onderzoek denken we ook dat onze methode kan worden toegepast in de biologie, zoals bijvoorbeeld zoölogisch onderzoek of ontwikkelingsbiologie.De techniek is relatief eenvoudig, zeer snel, en ook geschikt voor grotere weefselmo...

Video: 3D Imaging of Soft-Tissue Samples using an X-ray Specific Staining Method and Nanoscopic Computed Tomography

High Resolution 3D Imaging of Ex-Vivo Biological Samples by Micro CT

Non-destructive volume visualization can be achieved only by tomographic techniques, of which the most efficient is the x-ray micro computerized tomography (&mu;CT).
High resolution &mu;CT is a very versatile yet accurate (1-2 microns of resolution) technique for 3D examination of ex-vivo biological samples1, 2. As opposed to electron tomography, the &mu;CT allows the examination of up to 4 cm thick samples. This technique requires only few hours of measurement as compared to weeks in histology. In addition, &mu;CT does not rely on 2D stereologic models, thus it may complement and in some cases can even replace histological methods3, 4, which are both time consuming and destructive. Sample conditioning and positioning in &mu;CT is straightforward and does not require high vacuum or low temperatures, which may adversely affect the structure. The sample is positioned and rotated 180&deg; or 360&deg;between a microfocused x-ray source and a detector, which includes a scintillator and an accurate CCD camera, For each angle a 2D image is taken, and then the entire volume is reconstructed using one of the different available algorithms5-7. The 3D resolution increases with the decrease of the rotation step. The present video protocol shows the main steps in preparation, immobilization and positioning of the sample followed by imaging at high resolution.

High Resolution 3D Imaging of Ex-Vivo Biological Samples by Micro CT

Non-destructive volume visualization can be achieved only by tomographic techniques, of which the most efficient is the x-ray micro computerized tomography ( CT).

Non-destructive volume visualization can be achieved only by tomographic techniques, of which the most efficient is the x-ray micro computerized ...

Non-invasive 3D-Visualization with Sub-micron Resolution Using Synchrotron-X-ray-tomography

Little is known about the internal organization of many micro-arthropods with body sizes below 1 mm. The reasons for that are the small size and the hard cuticle which makes it difficult to use protocols of classical histology. In addition, histological sectioning destroys the sample and can therefore not be used for unique material. Hence, a non-destructive method is desirable which allows to view inside small samples without the need of sectioning.
We used synchrotron X-ray tomography at the European Synchrotron Radiation Facility (ESRF) in Grenoble (France) to non-invasively produce 3D tomographic datasets with a pixel-resolution of 0.7&micro;m. Using volume rendering software, this allows us to reconstruct the internal organization in its natural state without the artefacts produced by histological sectioning. These date can be used for quantitative morphology, landmarks, or for the visualization of animated movies to understand the structure of hidden body parts and to follow complete organ systems or tissues through the samples.

We used synchrotron X-ray tomography at the European Synchrotron Radiation Facility (ESRF) to non-invasively produce 3D tomographic datasets with a pixel-resolution of 0.7&micro;m. Using volume rendering software, this allows the reconstruction of internal structures in their natural state without the artefacts produced by histological sectioning.

Little is known about the internal organization of many micro-arthropods with body sizes below 1 mm. The reasons for that are the small size and the hard ...

Biology

Microfocus X-ray CT (microCT) Imaging of Actinia equina (Cnidaria), Harmothoe sp. (Annelida), and Xenoturbella japonica (Xenacoelomorpha)

Traditionally, biologists have had to rely on destructive methods such as sectioning in order to investigate the internal structures of opaque organisms. Non-destructive microfocus X-ray computed tomography (microCT) imaging has become a powerful and emerging protocol in biology, due to technological advancements in sample staining methods and innovations in microCT hardware, processing computers, and data analysis software. However, this protocol is not commonly used, as it is in the medical and industrial fields. One of the reasons for this limited use is the lack of a simple and comprehensible manual that covers all of the necessary steps: sample collection, fixation, staining, mounting, scanning, and data analyses. Another reason is the vast diversity of metazoans, particularly marine invertebrates. Because of marine invertebrates&#8217; diverse sizes, morphologies, and physiologies, it is crucial to adjust experimental conditions and hardware configurations at each step, depending on the sample. Here, microCT imaging methods are explained in detail using three phylogenetically diverse marine invertebrates: Actinia equina (Anthozoa, Cnidaria), Harmothoe sp. (Polychaeta, Annelida), and Xenoturbella japonica (Xenoturbellida, Xenacoelomorpha). Suggestions on performing microCT imaging on various animals are also provided.

Microfocus X-ray CT microCT Imaging of Actinia equina Cnidaria, Harmothoe sp. Annelida, and Xenoturbella japonica Xenacoelomorpha

Here, protocols for performing microfocus X-ray computed tomography (microCT) imaging of three marine invertebrate animals are explained in detail. This study describes steps such as sample fixation, staining, mounting, scanning, image reconstruction, and data analyses. Suggestions on how the protocol can be adjusted for different samples are also provided.

Traditionally, biologists have had to rely on destructive methods such as sectioning in order to investigate the internal structures of opaque organisms. ...

Environment

Whole Animal Imaging of Drosophila melanogaster using Microcomputed Tomography

Biomedical imaging tools permit investigation of molecular mechanisms across spatial scales, from genes to organisms. Drosophila melanogaster, a well-characterized model organism, has benefited from the use of light and electron microscopy to understand gene function at the level of cells and tissues. The application of imaging platforms that allow for an understanding of gene function at the level of the entire intact organism would further enhance our knowledge of genetic mechanisms. Here a whole animal imaging method is presented that outlines the steps needed to visualize Drosophila at any developmental stage using microcomputed tomography (&#181;-CT). The advantages of &#181;-CT include commercially available instrumentation and minimal hands-on time to produce accurate 3D information at micron-level resolution without the need for tissue dissection or clearing methods. Paired with software that accelerate image analysis and 3D rendering, detailed morphometric analysis of any tissue or organ system can be performed to better understand mechanisms of development, physiology, and anatomy for both descriptive and hypothesis testing studies. By utilizing an imaging workflow that incorporates the use of electron microscopy, light microscopy, and &#181;-CT, a thorough evaluation of gene function can be performed, thus furthering the usefulness of this powerful model organism.

Whole Animal Imaging of Drosophila melanogaster using Microcomputed Tomography

A protocol is presented that allows for the visualization of intact Drosophila melanogaster at any stage of development using microcomputed tomography.

Biomedical imaging tools permit investigation of molecular mechanisms across spatial scales, from genes to organisms. Drosophila melanogaster, a ...

Developmental Biology

Rigid Embedding of Fixed and Stained, Whole, Millimeter-Scale Specimens for Section-free 3D Histology by Micro-Computed Tomography

For over a hundred years, the histological study of tissues has been the gold standard for medical diagnosis because histology allows all cell types in every tissue to be identified and characterized. Our laboratory is actively working to make technological advances in X-ray micro-computed tomography (micro-CT) that will bring the diagnostic power of histology to the study of full tissue volumes at cellular resolution (i.e., an X-ray Histo-tomography modality). Toward this end, we have made targeted improvements to the sample preparation pipeline. One key optimization, and the focus of the present work, is a straightforward method for rigid embedding of fixed and stained millimeter-scale samples. Many of the published methods for sample immobilization and correlative micro-CT imaging rely on placing the samples in paraffin wax, agarose, or liquids such as alcohol. Our approach extends this work with custom procedures and the design of a 3-dimensional printable apparatus to embed the samples in an acrylic resin directly into polyimide tubing, which is relatively transparent to X-rays. Herein, sample preparation procedures are described for the samples from 0.5 to 10 mm in diameter, which would be suitable for whole zebrafish larvae and juveniles, or other animals and tissue samples of similar dimensions. As proof of concept, we have embedded the specimens from Danio, Drosophila, Daphnia, and a mouse embryo; representative images from 3-dimensional scans for three of these samples are shown. Importantly, our methodology leads to multiple benefits including rigid immobilization, long-term preservation of laboriously-created resources, and the ability to re-interrogate samples.

We developed protocols and designed a custom apparatus to enable embedding of millimeter-scale specimens. We present sample preparation procedures with an emphasis on embedding in acrylic resin and polyimide tubing to achieve rigid immobilization and long-term storage of specimens for the interrogation of tissue architecture and cell morphology by micro-CT.

For over a hundred years, the histological study of tissues has been the gold standard for medical diagnosis because histology allows all cell types in ...

Use of Micro X-ray Computed Tomography with Phosphotungstic Acid Preparation to Visualize Human Fibromuscular Tissue

Manual dissection and histological observation are common methods used to investigate human tissues. However, manual dissection can damage delicate structures&#160;while processing and histological observation provide limited information through cross-sectional imaging. Micro X-ray computed tomography (microCT) is an effective tool for obtaining three-dimensional information without damaging specimens. However, it shows limited efficiency in differentiating soft tissue parts. Use of contrast-enhancing agents, like phosphotungstic acid (PTA), can solve this problem by improving soft tissue contrast. We implemented microCT with PTA to investigate the human orbicularis retaining ligament (ORL), which is a delicate structure in the orbit area. In this method, harvested specimens are fixed in formalin, dehydrated in serial ethanol solutions, and stained with a PTA solution. After staining, microCT scanning, 3D reconstruction, and analysis are performed. Skin, ligaments, and muscles can be clearly visualized using this method. The specimen size and duration of staining are essential features of the method. The suitable specimen thickness was about 5&#8211;7 mm, above which the process was slowed, and the optimum duration was 5&#8211;7 days, below which an empty hole in the central area occasionally occurred. To maintain the location and direction of small pieces during cutting, sewing on the same region of each part is recommended. Furthermore, preliminary analyses of the anatomical structure are needed to correctly identify each piece. Parafilm can be used to prevent drying, but care should be taken to prevent specimen distortion. Our multidirectional observation showed that the ORL is composed of a multilayered meshwork of continuous plates, rather than thread-like fibers, as reported previously. These results suggest that microCT scanning with PTA is useful for examining specific compartments within complex structures of human tissue. It may be helpful in the analyses of cancer tissues, nerve tissues, and various organs, like the heart and liver.

Micro X-ray computed tomography is effective in obtaining three-dimensional information from undamaged human specimens but has limited success in observing soft tissues. The use of phosphotungstic acid contrast agent can resolve this issue. We implemented this contrast agent to examine human delicate fibromuscular tissues (the orbicularis retaining ligament).

Manual dissection and histological observation are common methods used to investigate human tissues. However, manual dissection can damage delicate ...

Using High Resolution Computed Tomography to Visualize the Three Dimensional Structure and Function of Plant Vasculature

High resolution x-ray computed tomography (HRCT) is a non-destructive diagnostic imaging technique with sub-micron resolution capability that is now being used to evaluate the structure and function of plant xylem network in three dimensions (3D) (e.g. Brodersen et al. 2010; 2011; 2012a,b). HRCT imaging is based on the same principles as medical CT systems, but a high intensity synchrotron x-ray source results in higher spatial resolution and decreased image acquisition time. Here, we demonstrate in detail how synchrotron-based HRCT (performed at the Advanced Light Source-LBNL Berkeley, CA, USA) in combination with Avizo software (VSG Inc., Burlington, MA, USA) is being used to explore plant xylem in excised tissue and living plants. This new imaging tool allows users to move beyond traditional static, 2D light or electron micrographs and study samples using virtual serial sections in any plane. An infinite number of slices in any orientation can be made on the same sample, a feature that is physically impossible using traditional microscopy methods.
Results demonstrate that HRCT can be applied to both herbaceous and woody plant species, and a range of plant organs (i.e. leaves, petioles, stems, trunks, roots). Figures presented here help demonstrate both a range of representative plant vascular anatomy and the type of detail extracted from HRCT datasets, including scans for coast redwood (Sequoia sempervirens), walnut (Juglans spp.), oak (Quercus spp.), and maple (Acer spp.) tree saplings to sunflowers (Helianthus annuus), grapevines (Vitis spp.), and ferns (Pteridium aquilinum and Woodwardia fimbriata). Excised and dried samples from woody species are easiest to scan and typically yield the best images. However, recent improvements (i.e. more rapid scans and sample stabilization) have made it possible to use this visualization technique on green tissues (e.g. petioles) and in living plants. On occasion some shrinkage of hydrated green plant tissues will cause images to blur and methods to avoid these issues are described. These recent advances with HRCT provide promising new insights into plant vascular function.

High resolution x-ray computed tomography (HRCT) is a non-destructive diagnostic imaging technique that can be used to study the structure and function of plant vasculature in 3D. We demonstrate how HRCT facilitates exploration of xylem networks across a wide range of plant tissues and species.

High resolution x-ray computed tomography (HRCT) is a non-destructive diagnostic imaging technique with sub-micron resolution capability that is now being ...

3D Printing of Preclinical X-ray Computed Tomographic Data Sets

Three-dimensional printing allows for the production of highly detailed objects through a process known as additive manufacturing. Traditional, mold-injection methods to create models or parts have several limitations, the most important of which is a difficulty in making highly complex products in a timely, cost-effective manner.1 However, gradual improvements in three-dimensional printing technology have resulted in both high-end and economy instruments that are now available for the facile production of customized models.2 These printers have the ability to extrude high-resolution objects with enough detail to accurately represent in vivo images generated from a preclinical X-ray CT scanner. With proper data collection, surface rendering, and stereolithographic editing, it is now possible and inexpensive to rapidly produce detailed skeletal and soft tissue structures from X-ray CT data. Even in the early stages of development, the anatomical models produced by three-dimensional printing appeal to both educators and researchers who can utilize the technology to improve visualization proficiency. 3, 4 The real benefits of this method result from the tangible experience a researcher can have with data that cannot be adequately conveyed through a computer screen. The translation of pre-clinical 3D data to a physical object that is an exact copy of the test subject is a powerful tool for visualization and communication, especially for relating imaging research to students, or those in other fields. Here, we provide a detailed method for printing plastic models of bone and organ structures derived from X-ray CT scans utilizing an Albira X-ray CT system in conjunction with PMOD, ImageJ, Meshlab, Netfabb, and ReplicatorG software packages.

Using modern plastic extrusion and printing technologies, it is now possible to quickly and inexpensively produce physical models of X-ray CT data taken in a laboratory. The three -dimensional printing of tomographic data is a powerful visualization, research, and educational tool that may now be accessed by the preclinical imaging community.

Three-dimensional printing allows for the production of highly detailed objects through a process known as additive manufacturing.  Traditional, ...

Nanoscopic Imaging of Human Tissue Sections via Physical and Isotropic Expansion

In modern pathology, optical microscopy plays an important role in disease diagnosis by revealing microscopic structures of clinical specimens. However, the fundamental physical diffraction limit prevents interrogation of nanoscale anatomy and subtle pathological changes when using conventional optical imaging approaches. Here, we describe a simple and inexpensive protocol, called expansion pathology (ExPath), for nanoscale optical imaging of common types of clinical primary tissue specimens, including both fixed-frozen or formalin-fixed paraffin embedded (FFPE) tissue sections. This method circumvents the optical diffraction limit by chemically transforming the tissue samples into tissue-hydrogel hybrid and physically expanding them isotropically across multiple scales in pure water. Due to expansion, previously unresolvable molecules are separated and thus can be observed using a conventional optical microscope.

Nanoscale imaging of clinical tissue samples can improve understanding of disease pathogenesis. Expansion pathology (ExPath) is a version of expansion microscopy (ExM), modified for compatibility with standard clinical tissue samples, to explore the nanoscale configuration of biomolecules using conventional diffraction limited microscopes.

In modern pathology, optical microscopy plays an important role in disease diagnosis by revealing microscopic structures of clinical specimens. However, ...

Medicine

A 3D Cartographic Description of the Cell by Cryo Soft X-ray Tomography

Imaging techniques are fundamental in order to understand cell organization and machinery in biological research and the related fields. Among these techniques, cryo soft X-ray tomography (SXT) allows imaging whole cryo-preserved cells in the water window X-ray energy range (284-543 eV), in which carbon structures have intrinsically higher absorption than water, allowing the 3D reconstruction of the linear absorption coefficient of the material contained in each voxel. Quantitative structural information at the level of whole cells up to 10 &#181;m thick is then achievable this way, with high throughput and spatial resolution down to 25-30 nm half-pitch. Cryo-SXT has proven itself relevant to current biomedical research, providing 3D information on cellular infection processes (virus, bacteria, or parasites), morphological changes due to diseases (such as recessive genetic diseases) and helping us understand drug action at the cellular level, or locating specific structures in the 3D cellular environment. In addition, by taking advantage of the tunable wavelength at synchrotron facilities, spectro-microscopy or its 3D counterpart, spectro-tomography, can also be used to image and quantify specific elements in the cell, such as calcium in biomineralization processes. Cryo-SXT provides complementary information to other biological imaging techniques such as electron microscopy, X-ray fluorescence or visible light fluorescence, and is generally used as a partner method for 2D or 3D correlative imaging at cryogenic conditions in order to link function, location, and morphology.

Here, a protocol describing the sample preparation and data collection steps required in cryo soft X-ray tomography (SXT) to image the ultrastructure of whole cryo-preserved cells at a resolution of 25 nm half pitch, is presented.

Imaging techniques are fundamental in order to understand cell organization and machinery in biological research and the related fields. Among these ...

3D Imaging of Soft-Tissue Samples using an X-ray Specific Staining Method and Nanoscopic Computed Tomography

Samenvatting

Meer video's verkennen