The authors acknowledge support from Samsung, the NC State Chancellors Innovation Funds, NSF (CAREER CMMI-0954321 and Triangle MRSEC DMR-1121107), and Air Force Research Labs.

1. Manipulation of the Interfacial Tension of Liquid Metal in Electrolyte
<ol>
	<li>Oxidation
	<ol>
		<li>Pour an aqueous electrolyte (acidic or basic) into a Petri dish. To ensure that the oxide is completely removed, use an acid or base with a concentration greater than 0.1 M24 (e.g. 1 M NaOH or 1 M HCl). Use a volume that will fill the dish to a depth of approximately 1-3 mm. Avoid contacting the skin with these solutions.</li>
		<li>Use a syringe to place a drop (optimally between 10-500 &#181;l) of a gallium-based alloy in the electrolyte. Examples include eutectic gallium indium (EGaIn) or gallium indium tin (Galinstan). If pure gallium is used, warm the electrolyte to at least 30 &#176;C to prevent freezing.</li>
		<li>Place a copper wire into the liquid metal to establish the working electrode. Use a copper wire with a diameter less than that of the drop, and use a digital multimeter according to manufacturer&#39;s instructions to ensure that the wire has a resistance of &#60; 1 &#937;. In acid or base, the liquid metal will wet the copper and thereby form an excellent electrical contact.</li>
		<li>Place a conducting counter-electrode (e.g. copper, graphite, platinum, etc.) in the solution, but not in contact with the liquid metal. If the counter-electrode has a resistance of &#60; 1 &#937;, its dimensions are irrelevant.</li>
		<li>Connect the wires to a voltage source and apply a positive potential to the liquid metal. For small shape deformation, apply positive voltages &#60; 1 V. For larger shape deformation (and movement of the liquid metal toward the counter-electrode), apply &#62; 1 V. 
		Note: The concentration of the solution and the distance of the drop from the counter-electrode dictate the voltage necessary to induce changes in interfacial tension since the rate of electrochemical surface oxidation competes with the rate of oxide dissolution by the electrolyte.</li>
	</ol>
	</li>
	<li>Reduction
	<ol>
		<li>Dispense a drop (10-500 &#956;l) of the liquid metal from a syringe into an empty Petri dish.</li>
		<li>Pour a neutral aqueous electrolyte into the Petri dish (e.g. 1 M sodium fluoride (NaF) or 1 M sodium chloride (NaCl)) to a level that submerges the metal. 
		Note: Use of an acidic (pH &#60; 3) or basic solution (pH &#62; 10) will cause the oxide to dissolve spontaneously.</li>
		<li>Place a copper wire into the liquid metal to act as a working electrode, and a conducting wire (e.g., copper) into the electrolyte to act as the counter-electrode.</li>
		<li>Connect the wires to a voltage source and apply a negative potential to the liquid metal. Apply approximately -1 V to remove the surface oxide and cause the metal to dewet from the substrate. The metal should dewet on the side closest to the counter-electrode.</li>
		<li>Apply more negative potentials (&#60;-1 V) to remove the oxide layer completely. Avoid applying excessively large negative voltages to prevent hydrogen bubbles from appearing on the liquid metal due to reduction of the electrolyte.</li>
	</ol>
	</li>
</ol>
2. Surface Tension Measurement via Sessile Droplet
<ol>
	<li>Using a laser cutter or milling tool, cut a direct path from the center to the edge of a piece of polymethylmethacrylate (PMMA) (~1 mm thick). Do not cut the path all the way through the thickness of the PMMA; only cut about halfway through. This piece will serve as a substrate for the liquid metal. Other flat and electrically insulating materials such as glass, ceramics, or polymers can also serve as the substrate.</li>
	<li>With the same tool, cut a 1 mm2 hole through the center of the PMMA.</li>
	<li>Using the path as a guide, run an insulated copper wire with only the tip exposed to the center of the PMMA. Position the wire so that it is protruding over the PMMA surface. Seal the wire in place with a leakproof adhesive. Cut the wire just above the surface of the PMMA, but do not let it extend too far (beyond ~100 &#956;m) or it will disturb the shape of the drop.</li>
	<li>Tape the PMMA piece down into a transparent container through which a clear image can be obtained. Fill the container with 1 M NaOH, and place a 25-50 &#181;l drop of liquid metal on the protruding copper wire. This wire will serve as the working electrode and will wet the droplet.</li>
	<li>Place a platinum mesh counter-electrode and a saturated silver/silver chloride (Ag/AgCl) reference electrode in the solution. Connect all of the electrodes to a potentiostat.</li>
	<li>Place the container in a contact angle goniometer so that the surface profile of the drop is clearly visible. Use the potentiostat to control the voltage with respect to the reference electrode, and use the goniometer to measure the shape and thereby the interfacial tension of the drop. Ensure that the goniometer is capable of measuring sessile drop interfacial tension; it is also possible to use custom axisymmetric shape analysis of drop images taken from a horizontally mounted camera 25.</li>
</ol>
3. Capillary Injection
<ol>
	<li>Fill a glass capillary with a solution of 1 M NaOH. The capillary diameter should be ~1 mm.</li>
	<li>Place one end of the capillary flush against a drop of liquid metal. Align the capillary so that it is parallel with the surface of the table (i.e., perpendicular to gravity). Avoid air gaps between the liquid metal drop and electrolyte-filled capillary. Using a wipe, dab off any excess electrolyte that may have leaked during assembly.</li>
	<li>Place a copper wire (working electrode) in the liquid metal, and a conductive counter-electrode (e.g. copper wire) in the open end of the capillary so that it contacts the solution.</li>
	<li>Connect the wires to a voltage source and apply a positive potential to the liquid metal. The liquid metal should begin filling the capillary (avoid large potentials that will cause excess bubble formation on the counter-electrode).</li>
</ol>
4. Capillary Withdrawal
<ol>
	<li>Utilize soft lithographic26 and replica molding techniques to fabricate microfluidic channels composed of polydimethylsiloxane (PDMS). Fabricate channels that are approximately 100 to 1,000 &#181;m wide, 100 &#181;m tall, and 25 to 65 mm long. 
	Note: Channel dimensions 1,000 &#181;m wide, 100 &#181;m tall, and 65 mm long channel produced consistent results, but others may also work. Alternatively, use glass capillaries (e.g., 1 mm diameter, borosilicate glass) instead of PDMS microchannels.</li>
	<li>Inject liquid metal either manually or using a syringe pump to fill the channel completely (i.e., 6.5 mm3 for a 1,000 &#181;m wide, 100 &#181;m tall, and 65 mm long channel).</li>
	<li>Using a cotton swab that has been dipped in 1 M NaOH or 1 M HCl, remove excess amounts of liquid metal from the inlet (and, if necessary, the outlet) of the channel, so that the metal remains flush with the top surface of the PDMS.</li>
	<li>Submerge one end of the channel in electrolyte (e.g., 1 M NaCl), and place the anode (e.g., wires of copper, platinum, or tungsten) such that it touches the electrolyte but not the metal.</li>
	<li>At the other end of the channel, contact a separate electrode (e.g., Cu wire) to the metal surface so that liquid metal itself acts as a cathode.</li>
	<li>Connect these wires (i.e., anode and cathode) to a voltage source or potentiostat, and complete the electric circuit. For a three electrode system, place the reference electrode such that it barely submerges into the drop of electrolyte.</li>
	<li>Before applying a reducing voltage, mount a video camera on a tripod or in a microscope to record the experiments. Use autofocus mode to get everything in focus. Utilize manual focus to have a better control over depth of field, white balance, and ISO. As necessary, use higher F stop (i.e., 11 or higher), 1/100th shutter, auto white balance and auto ISO.</li>
	<li>Start recording the experiment. Apply approximately -1 V to withdraw the liquid metal from the microchannels. Turn the voltage off to cause the metal to stop moving in neutral electrolyte.</li>
</ol>

<ol><li>Khan, M. R., Eaker, C. B., Bowden, E. F., Dickey, M. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Giant+and+switchable+surface+activity+of+liquid+metal+via+surface+oxidation%5BTitle%5D)+AND+%22Proc.+Natl.+Acad.+Sci%22%5BJournal%5D)">Giant and switchable surface activity of liquid metal via surface oxidation.</a> Proc. Natl. Acad. Sci. 111 (39), 14047-14051 (2014).</li>
<li>Kataoka, D. E., Troian, S. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Patterning+liquid+flow+on+the+microscopic+scale%5BTitle%5D)+AND+%22Nature%22%5BJournal%5D)">Patterning liquid flow on the microscopic scale.</a> Nature. 402 (6763), 794-797 (1999).</li>
<li>Daniel, S., Chaudhury, M. K., Chen, J. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Fast+Drop+Movements+Resulting+from+the+Phase+Change+on+a+Gradient+Surface%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Fast Drop Movements Resulting from the Phase Change on a Gradient Surface.</a> Science. 291 (5504), 633-636 (2001).</li>
<li>Ichimura, K., Oh, S. K., Nakagawa, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Light-driven+motion+of+liquids+on+a+photoresponsive+surface%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Light-driven motion of liquids on a photoresponsive surface.</a> Science. 288 (5471), 1624-1626 (2000).</li>
<li>Gallardo, B. S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Electrochemical+principles+for+active+control+of+liquids+on+submillimeter+scales%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Electrochemical principles for active control of liquids on submillimeter scales.</a> Science. 283 (5398), 57-60 (1999).</li>
<li>Zhao, B., Moore, J. S., Beebe, D. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Surface-Directed+Liquid+Flow+Inside+Microchannels%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Surface-Directed Liquid Flow Inside Microchannels.</a> Science. 291 (5506), 1023-1026 (2001).</li>
<li>Chaudhury, M. K., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((How+to+Make+Water+Run+Uphill%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">How to Make Water Run Uphill.</a> Science. 256 (5063), 1539-1541 (1992).</li>
<li>Lahann, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+reversibly+switching+surface%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">A reversibly switching surface.</a> Science. 299 (5605), 371-374 (2003).</li>
<li>Rogers, J. A., Someya, T., Huang, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Materials+and+Mechanics+for+Stretchable+Electronics%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Materials and Mechanics for Stretchable Electronics.</a> Science. 327 (5973), 1603-1607 (2010).</li>
<li>Bauer, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((25th+Anniversary+Article%3A+A+Soft+Future%3A+From+Robots+and+Sensor+Skin+to+Energy+Harvesters%5BTitle%5D)+AND+%22Adv.+Mater%22%5BJournal%5D)">25th Anniversary Article: A Soft Future: From Robots and Sensor Skin to Energy Harvesters.</a> Adv. Mater. 26 (1), 149-162 (2013).</li>
<li>Ozbay, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Plasmonics%3A+Merging+Photonics+and+Electronics+at+Nanoscale+Dimensions%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Plasmonics: Merging Photonics and Electronics at Nanoscale Dimensions.</a> Science. 311 (5758), 189-193 (2006).</li>
<li>Monat, C., Domachuk, P., Eggleton, B. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Integrated+optofluidics%3A+A+new+river+of+light%5BTitle%5D)+AND+%22Nat.+Photonics%22%5BJournal%5D)">Integrated optofluidics: A new river of light.</a> Nat. Photonics. 1 (2), 106-114 (2007).</li>
<li>Schurig, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Metamaterial+Electromagnetic+Cloak+at+Microwave+Frequencies%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Metamaterial Electromagnetic Cloak at Microwave Frequencies.</a> Science. 314 (5801), 977-980 (2006).</li>
<li>Dickey, M. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Emerging+Applications+of+Liquid+Metals+Featuring+Surface+Oxides%5BTitle%5D)+AND+%22ACS+Appl.+Mater.+Interfaces%22%5BJournal%5D)">Emerging Applications of Liquid Metals Featuring Surface Oxides.</a> ACS Appl. Mater. Interfaces. 6 (21), 18369-18379 (2014).</li>
<li>Dickey, M. D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Eutectic+gallium-indium+%28EGaIn%29%3A+A+liquid+metal+alloy+for+the+formation+of+stable+structures+in+microchannels+at+room+temperature%5BTitle%5D)+AND+%22Adv.+Funct.+Mater%22%5BJournal%5D)">Eutectic gallium-indium (EGaIn): A liquid metal alloy for the formation of stable structures in microchannels at room temperature.</a> Adv. Funct. Mater. 18 (7), 1097-1104 (2008).</li>
<li>Regan, M. J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((X-ray+study+of+the+oxidation+of+liquid-gallium+surfaces%5BTitle%5D)+AND+%22Phys.+Rev.+B%22%5BJournal%5D)">X-ray study of the oxidation of liquid-gallium surfaces.</a> Phys. Rev. B. 55 (16), 10786-10790 (1997).</li>
<li>Giguère, P. A., Lamontagne, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Polarography+with+a+Dropping+Gallium+Electrode%5BTitle%5D)+AND+%22Science%22%5BJournal%5D)">Polarography with a Dropping Gallium Electrode.</a> Science. 120 (3114), 390-391 (1954).</li>
<li>Frumkin, A., Polianovskaya, N., Grigoryev, N., Bagotskaya, I. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Electrocapillary+phenomena+on+gallium%5BTitle%5D)+AND+%22Electrochim.+Acta%22%5BJournal%5D)">Electrocapillary phenomena on gallium.</a> Electrochim. Acta. 10 (8), 793-802 (1965).</li>
<li>Lippmann, G. France Université. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aLippmann%2C+G+%22Relations+entre+les+ph%C3%A9nom%C3%A8nes+%C3%A9lectriques+et+capillaires%22">Relations entre les phénomènes électriques et capillaires</a>. , Gauthier-Villars. (1875).</li>
<li>Tsai, J. T. H., Ho, C. M., Wang, F. C., Liang, C. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Ultrahigh+contrast+light+valve+driven+by+electrocapillarity+of+liquid+gallium%5BTitle%5D)+AND+%22Appl.+Phys.+Lett%22%5BJournal%5D)">Ultrahigh contrast light valve driven by electrocapillarity of liquid gallium.</a> Appl. Phys. Lett. 95 (25), 251110(2009).</li>
<li>Khan, M. R., Trlica, C., Dickey, M. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Recapillarity%3A+Electrochemically+Controlled+Capillary+Withdrawal+of+a+Liquid+Metal+Alloy+from+Microchannels%5BTitle%5D)+AND+%22Adv.+Funct.+Mater%22%5BJournal%5D)">Recapillarity: Electrochemically Controlled Capillary Withdrawal of a Liquid Metal Alloy from Microchannels.</a> Adv. Funct. Mater. 25 (5), 671-678 (2015).</li>
<li>Saltman, W., Nachtrieb, N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((The+Electrochemistry+of+Gallium%5BTitle%5D)+AND+%22J.+Electrochem.+Soc%22%5BJournal%5D)">The Electrochemistry of Gallium.</a> J. Electrochem. Soc. 100, 126-130 (1953).</li>
<li>Perkins, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Anodic-Oxidation+of+Gallium+in+Alkaline-Solution%5BTitle%5D)+AND+%22J.+Electroanal.+Chem%22%5BJournal%5D)">Anodic-Oxidation of Gallium in Alkaline-Solution.</a> J. Electroanal. Chem. 101, 47-57 (1979).</li>
<li>Xu, Q., Oudalov, N., Guo, Q., Jaeger, H. M., Brown, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Effect+of+oxidation+on+the+mechanical+properties+of+liquid+gallium+and+eutectic+gallium-indium%5BTitle%5D)+AND+%22Phys.+Fluids%22%5BJournal%5D)">Effect of oxidation on the mechanical properties of liquid gallium and eutectic gallium-indium.</a> Phys. Fluids. 24, 063101(2012).</li>
<li>Rotenberg, Y., Boruvka, L., Neumann, A. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Determination+of+surface+tension+and+contact+angle+from+the+shapes+of+axisymmetric+fluid+interfaces%5BTitle%5D)+AND+%22J.+Colloid+Interface+Sci%22%5BJournal%5D)">Determination of surface tension and contact angle from the shapes of axisymmetric fluid interfaces.</a> J. Colloid Interface Sci. 93, 169-183 (1983).</li>
<li>Xia, Y., Whitesides, G. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Soft+Lithography%5BTitle%5D)+AND+%22Annu.+Rev.+Mater.+Sci%22%5BJournal%5D)">Soft Lithography.</a> Annu. Rev. Mater. Sci. 28 (1), 153-184 (1998).</li>
<li>Pourbaix, M. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aPourbaix%2C+M+%22Atlas+of+Electrochemical+Equilibria+in+Aqueous+Solutions%22">Atlas of Electrochemical Equilibria in Aqueous Solutions</a>. , Natl Assn of Corrosion. (1974).</li>
<li>Gough, R. C., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Rapid+electrocapillary+deformation+of+liquid+metal+with+reversible+shape+retention%5BTitle%5D)+AND+%22Micro+Nano+Syst.+Lett%22%5BJournal%5D)">Rapid electrocapillary deformation of liquid metal with reversible shape retention.</a> Micro Nano Syst. Lett. 3 (1), 1-9 (2015).</li>
<li>Wang, M., Trlica, C., Khan, M. R., Dickey, M. D., Adams, J. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+reconfigurable+liquid+metal+antenna+driven+by+electrochemically+controlled+capillarity%5BTitle%5D)+AND+%22J.+Appl.+Phys%22%5BJournal%5D)">A reconfigurable liquid metal antenna driven by electrochemically controlled capillarity.</a> J. Appl. Phys. 117 (19), 194901(2015).</li>
</ol>

The authors have nothing to disclose.

This method controls the surface tension of gallium-based liquid metals using small voltages to drive the deposition and removal of a surface oxide. Although the method only works in electrolyte solutions, it is simple, and works in a wide variety of different conditions, but there are subtleties worth noting. In the absence of electrical potential, both acidic and basic solutions etch away the oxide27. The application of an oxidative potential drives the formation of surface oxide in all aqueous electrolytes, including acidic and basic solutions. However, dissolution of the oxide in acidic or basic solutions competes with the deposition of the oxide to prevent excessive build-up of the oxide layer. The formation of a thick oxide layer inhibits flow, presumably since the oxide provides a mechanical barrier to movement. This inhibition can be detrimental during spreading, but also provides a method to stabilize the shape of the metal.
The interfacial tension varies continuously as a function of potential. The surface tension is largest at the potential that removes the surface oxide. Potentials that are more reductive (more negative) will slightly decrease the surface tension due to classic electrocapillarity (cf., Figure 1B). This decrease continues as a function of potential until Faradaic processes (e.g. hydrogen formation) occur at the surface.
In contrast, the surface tension drops significantly at the potential where the oxide first forms (cf. Figure 1B). Increasing the (positive) potential continues to lower the surface tension, presumably due to better coverage of the surface oxide. Beyond a &#34;critical potential&#34;, the drop will begin spreading without bound, forming fractal-like patterns and migrating toward the counter-electrode. This movement continues until the voltage is removed, or until the drop breaks contact with the working electrode. The shapes formed in the region above the critical potential are still being investigated but are attributed to the surface tension being near zero. Details can be found in the literature1.
The interfacial tension of the metal is sensitive to small changes in voltage. It is therefore important to have excellent electrical contact with the metal and control over the potential applied to the liquid metal. In addition, the presence of acid or base in the electrolyte competes with electrochemical oxidation by dissolving the oxide layer. This competing process adds a level of complexity; understanding the complex process that occur at the interface will be critical for advancing this method.
Oxidative and reductive processes can be combined to provide control over the flow of metal in and out of capillaries. For example, it is possible to use oxidative potentials to inject metal into capillaries (by lowering the interfacial tension of the leading meniscus, as shown in Figure 2), and then use reductive potentials to induce the metal to retreat from the capillary (by increasing the interfacial tension of the leading meniscus, as shown in Figure 3)28,29. The limits and capabilities of this approach are yet to be fully determined, although injection appears to be slower than withdrawal. Using oxidation to inject metal involves three critical steps. First, the capillary should be prefilled with electrolyte, which we believe creates a thin &#34;slip layer&#34; of water between the metal and the walls of the capillary as the metal. Second, injecting the metal into a capillary requires flush contact between a bead of the metal and the end of the capillary, as shown in Figure 3. This intimate contact ensures the potential drop occurs at the electrolyte / metal interface and prevents pathways for charge to bypass this interface.
It is possible to use either two-electrode or three-electrode systems to control the surface tension of the metal. The two-electrode system is the simplest, requiring only a working electrode, counter electrode, and voltage source. Although the two-electrode system is suitable for demonstrations, the potential of the counter-electrode can drift. Sensitive electrochemical measurements benefit from the stability of three-electrode system (i.e., a reference electrode and a potentiostat). This system allows for better control of the voltage, and provides an accurate reading of the current.
The ability to control interfacial tension using modest voltages is a promising method for controlling the shape, flow, and position of metallic structures at the sub-mm length scale. We believe this technique may be useful for creating metallic structures that change shape on demand, which may find applications in shape reconfigurable electronics, tunable antennas, switches, microfluidic components, optofluidics, and shape-shifting meta-materials.

This method provides a simple way to control the surface tension of liquid metals containing gallium. The method uses modest voltages (~1 V) applied directly to the liquid metal (relative to a counter electrode in the presence of electrolyte) to achieve enormous and reversible changes to the surface tension of the metal1. 
Surface tension is a dominant force for liquids at small length scales and is important for a number of capillary phenomena including wetting, spreading, and surface-tension driven flow. Consequently, the ability to control surface tension is a sensible way to manipulate the shape, position, and flow of liquids at sub-mm length scales. The most common way to alter surface tension between two fluids is to use a surfactant, which is a molecule that spans the interface between the fluids. Surfactants lower surface tension, but in a way that is not easy to reverse since it is difficult to remove surfactants from the interface. Surface tension can also be altered using a variety of techniques, including temperature gradients2,3, light4, surface chemistry5-7,and voltage8. But most of these methods result in modest changes to surface tension, particularly for liquid metals, which have notably large surface tensions.
The ability to control the surface tension of liquid metal could enable new opportunities for creating shape reconfigurable structures with metallic properties for electronic, thermal, and optical applications9-14. The most common liquid metal is Hg, which is noted for its toxicity. The methods described here are relevant for liquid metals based on gallium. These metals have low viscosity, large surface tension, low volatility (low vapor pressure), and low toxicity15. Importantly, these metals form surface oxides composed of gallium oxide that are a few nm thick in air16. This oxide layer creates a physical skin that historically has been a nuisance for electrochemical and fluid dynamic applications17. The method here utilizes the oxide in new ways to control surface tension.
The most common way to manipulate liquid metals in electrolyte is to apply a potential to the metal relative to a counter electrode18. Oppositely charged ions from the electrolyte match the charges on the metal, causing the interfacial tension to drop. This phenomenon-termed electrocapillarity-has been known since the 1870s as described by Lippman19and has been utilized for alloys of gallium20. Typically, electrocapillarity achieves modest changes to surface tension, since undesirable electrochemical reactions limit the range of voltages applied to the metal. In contrast, the method described here utilizes the surface oxidation of the metal (or conversely, the reduction of the surface oxide) as a way to achieve enormous changes in surface tension above and beyond changes resulting from electrocapillarity. The leading explanation for this phenomenon is that the oxide is asymmetric; that is, the outer surface of the oxide terminates with hydroxyl groups (making a low interfacial tension interface with the aqueous electrolyte), and the interior surface of the oxide terminates with gallium atoms (making a low interfacial tension interface with the metal). In contrast, the removal of the oxide via electrochemical reduction results in a bare metal-electrolyte interface, which returns the metal back to a state of high surface tension. We characterize the interfacial tension of the metal by analyzing the shape of sessile droplets as a function of voltage while assuming that gravity and surface tension are the dominant forces that define the curvature of its surface. 
The advantage of this technique relative to classic electrocapillarity is that it can reversibly tune the tension of low toxicity liquid metals over enormous ranges (from ~500 mN/m to near zero). This delta change in surface tension may be the largest ever reported in literature for any fluid and it can be accomplished in a tunable and reversible manner. These large changes in surface tension are useful for manipulating the capillary behavior of metals; for example, it can induce the metal to spread on a surface, withdraw the metal from microchannels, fill microchannels with metal, and overcome the Rayleigh instabilities to form liquid metal fibers1,21. 
A drawback of this technique is that it requires electrolyte. It works best in acidic or basic conditions, because these electrolytes remove excess surface oxide that would otherwise contaminate the surface of the metal and mechanically restrict the movement of the metal. The simultaneous removal and deposition of the oxide layer complicates the analysis of the interfacial phenomena and it is our hope the methods described in this paper empowers additional analysis. Another disadvantage is that the electrochemical reactions at the surface of the metal must be matched by complimentary half-reactions at the counter electrode22,23. This can lead to hydrogen bubbles forming at the counter electrode.

<table><tbody><tr><td>Eutectic Gallium Indium</td><td>Indium Corporation</td><td></td><td></td></tr><tr><td>Sodium Hydroxide</td><td>Fisher Scientific</td><td>2318-3</td><td></td></tr><tr><td>Hydrochloric Acid</td><td>Fisher Scientific</td><td>A481-212</td><td></td></tr><tr><td>Sodium Fluoride</td><td>Sigma-Aldrich</td><td>201154</td><td></td></tr><tr><td>Optical Adhesive</td><td>Norland</td><td>NOA81</td><td></td></tr><tr><td>Polydimethylsiloxane (Sylgard-184)</td><td>Dow Corning</td><td></td><td>Silicone Elastomer Kit</td></tr><tr><td>Borosilicate Glass Capillaries</td><td>Friedrich and Dimmoch</td><td>B41972</td><td></td></tr><tr><td>Ag/AgCl Reference Electrode</td><td>Microelectrodes Inc.</td><td>MI-401F</td><td></td></tr><tr><td>Voltage Source</td><td>Keithley</td><td>3390</td><td></td></tr><tr><td>Potentiostat</td><td>Gamry</td><td>Ref 600</td><td></td></tr><tr><td>Laser Cutter</td><td>Universal Laser Systems</td><td>VLS 3.50</td><td></td></tr></tbody></table>

a method to manipulate surface tension of a liquid metal via surface oxidation and reduction

Controlling interfacial tension is an effective method for manipulating the shape, position, and flow of fluids at sub-millimeter length scales, where interfacial tension is a dominant force. A variety of methods exist for controlling the interfacial tension of aqueous and organic liquids on this scale; however, these techniques have limited utility for liquid metals due to their large interfacial tension.
Liquid metals can form soft, stretchable, and shape-reconfigurable components in electronic and electromagnetic devices. Although it is possible to manipulate these fluids via mechanical methods (e.g., pumping), electrical methods are easier to miniaturize, control, and implement. However, most electrical techniques have their own constraints: electrowetting-on-dielectric requires large (kV) potentials for modest actuation, electrocapillarity can affect relatively small changes in the interfacial tension, and continuous electrowetting is limited to plugs of the liquid metal in capillaries.
Here, we present a method for actuating gallium and gallium-based liquid metal alloys via an electrochemical surface reaction. Controlling the electrochemical potential on the surface of the liquid metal in electrolyte rapidly and reversibly changes the interfacial tension by over two orders of magnitude ( &#820;500 mN/m to near zero). Furthermore, this method requires only a very modest potential (&#60; 1 V) applied relative to a counter electrode. The resulting change in tension is due primarily to the electrochemical deposition of a surface oxide layer, which acts as a surfactant; removal of the oxide increases the interfacial tension, and vice versa. This technique can be applied in a wide variety of electrolytes and is independent of the substrate on which it rests.

Figure 1A shows an example of the simple two-electrode technique for oxidation and reduction. In this instance, a 70 &#181;l drop of the liquid metal placed in a 1 M NaOH solution contacts a copper wire to establish an electrical connection. The 1 M NaOH removes the surface oxide from the metal and allows the metal to bead up due to its interfacial tension. Applying a 2.5 V potential between the drop and a platinum mesh counter-electrode causes the surface of the drop to oxidize and the drop spreads while migrating toward the counter-electrode (Figure 1Aii). Applying a -1 V potential to the liquid metal removes the oxide (in addition to the removal of the oxide by NaOH), causes the metal to bead up, and generates hydrogen bubbles on the drop due to the reductive potential (Figure 1Ai). Hydrogen bubbles form on the platinum counter electrode due to the complimentary electrochemical half-reaction that presumably reduces protons in solution.
An electrocapillary curve (Figure 1B) shows the dramatic drop in effective surface tension when the oxide layer forms. These data were taken in 1 M NaOH using a saturated Ag/AgCl reference electrode. In this case, the open circuit potential was approximately -1.5 V vs. Ag/AgCl, and the oxide layer formed near -1.3 V vs. Ag/AgCl (indicated by the dotted lines). The use of 1 M HCl results in similar phenomenological behavior, but the formation of bubbles on the surface of the metal, even at oxidative potentials, makes visual analysis difficult.
In the absence of the oxide (which is removed by 1 M NaOH, for example), bare liquid metal is a high surface tension fluid and adopts a spherical shape as shown in Figure 2A. A drop of liquid metal rests adjacent to a capillary tube filled with 1 M NaOH. A wipe removes excess electrolyte from the bottom of the droplet, as shown by Figure 2B. A copper wire touches the droplet to form the anode and the other electrode (i.e., cathode; not shown in Figure 2) rests inside the electrolyte filled capillary tube. The electrolyte in the capillary completes the circuit between the two electrodes, as shown in Figure 2C. Applying +1 V lowers the surface tension at the leading interface and causes the liquid metal to fill the capillary as shown in Figure 2D. This experiment works best if the metal is flush with the end of the tube.
In contrast, a reducing bias removes the oxide skin and returns the metal to a state of large surface tension. One such example is shown in Figure 3A. The oxide skin stabilizes the shape of a puddle of liquid metal submerged in neutral electrolyte (Figure 3Ai). Application of a reducing bias removes the oxide skin, allowing the metal to bead up as shown in Figure 3A(ii-iii). We call this technique &#34;recapillarity&#34; since it uses reductive potentials to induce capillary behaviors21. The other implication of this term is that capillary behavior can be turned on or off multiple times. For example, EGaIn can be withdrawn from PDMS microfluidic channels by reducing the oxide that otherwise stabilizes the metal in the channels (as described in 4.1). Figure 3B-D illustrates one such experimental sequence.
We insert a syringe needle at one end of the capillary and slowly push the syringe plunger to force the metal from the syringe into the capillary. We place the filled capillary on a custom holder composed of polymethylmethacrylate (PMMA). The holder has two reservoirs, two grooves to secure the capillary, two holes to insert wires, and also has the option to tape a ruler, as shown in Figure 3B. Electrolyte (e.g. aqueous sodium fluoride) added to the reservoir after injecting the metal connects the anode to the end of the capillary, as shown in Figure 3C. The metal inside the tube contacts the counter electrode on the other end of the capillary to complete the circuit. Applying 1V reducing bias causes the metal to withdraw and move away from the anode, as shown in Figure 3D. Later, we measure the withdrawal velocity by comparing the position of the metal with respect to time. One such velocity plot is shown in Figure 3E. The velocity decays as the metal moves away from the anode. This velocity decay is due to the increase in electrical resistance between the anode and the liquid metal21.
<img alt="Figure 1" src="/files/ftp_upload/53567/53567fig1.jpg" /> 
Figure 1. (A) A drop of EGaIn submerged in 1 M NaOH, with a copper wire attached to the drop and a platinum counter-electrode mesh in solution. i) A -1 V potential applied to the drop causes the metal to bead up and produces hydrogen on the surface of the metal. ii) A 2.5 V potential applied to the drop induces spreading. (B) An electrocapillary curve of an EGaIn drop in 1 M NaOH. The reductive side (voltages below -1.4 V vs. Ag/AgCl) shows traditional electrocapillarity behavior, while the oxidative side shows a significant drop in surface tension. Figure 1B adopted from Reference 1 (Copyright 2014, National Academy of Sciences, USA). <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53567/53567fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 2" src="/files/ftp_upload/53567/53567fig2.jpg" /> 
Figure 2. Capillary injection of liquid metal using oxidative bias. (A) A drop of liquid metal contacts the opening to a capillary tube filled with electrolyte. (B) The tube is aligned and pushed against the drop. A wipe removes the excess amount of electrolyte. (C) A labeled image of this experimental set-up. (D) Application of +1 V to the metal lowers the surface tension of the metal via surface oxidation, and induces flow. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53567/53567fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<img alt="Figure 3" src="/files/ftp_upload/53567/53567fig3.jpg" /> 
Figure 3. (A) A drop of the liquid metal in 1 M NaF solution. i) The oxide allows a stable, non-spherical puddle in the solution. ii-iii) Applying a -1 V potential causes the metal to bead up. (B) A custom made acrylic substrate has two reservoirs into which electrodes are inserted. A 70 mm long, 1 mm ID glass capillary filled with EGaIn spans the two reservoirs. The substrate has two grooves to fit this capillary firmly. (C) A drop of electrolyte is added to one reservoir, and the other reservoir is left as is. Sometimes bubbles form, which can be minimized by using a fine tip needle. (D) Application of a reducing bias removes the oxide and causes the metal to withdraw. (E) Withdrawal velocity of the liquid metal from the capillary as a function of time. <a href="https://www-jove-com.remotexs.ntu.edu.sg/files/ftp_upload/53567/53567fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

Watch this Scientific Journal Video about A Method to Manipulate Surface Tension of a Liquid Metal via Surface Oxidation and Reduction at JoVE.com

A Method to Manipulate Surface Tension of a Liquid Metal via Surface Oxidation and Reduction

We present a method to control the interfacial energy of a liquid metal in an electrolyte via electrochemical deposition (or removal) of a surface oxide layer. This simple method can control the capillary behavior of gallium-based liquid metals by tuning the interfacial energy rapidly, significantly, and reversibly using modest voltages.

Controlling interfacial tension is an effective method for manipulating the shape, position, and flow of fluids at sub-millimeter length scales, where ...

a-method-to-manipulate-surface-tension-liquid-metal-via-surface

Nanyang Technological University

Research

Education

JoVE Journal

JoVE Core

Chemistry

Liquids, Solids, and Intermolecular Forces

SCIENTISTS IN ACTION

15.3K Views.  North Carolina State University. We present a method to control the interfacial energy of a liquid metal in an electrolyte via electrochemical deposition (or removal) of a surface oxide layer. This simple method can control the capillary behavior of gallium-based liquid metals by tuning the interfacial energy rapidly, significantly, and reversibly using modest voltages.

Video: A Method to Manipulate Surface Tension of a Liquid Metal via Surface Oxidation and Reduction

Taking Advantage of Reduced Droplet-surface Interaction to Optimize Transport of Bioanalytes in Digital Microfluidics

Digital microfluidics (DMF), a technique for manipulation of droplets, is a promising alternative for the development of &#8220;lab-on-a-chip&#8221; platforms. Often, droplet motion relies on the wetting of a surface, directly associated with the application of an electric field; surface interactions, however, make motion dependent on droplet contents, limiting the breadth of applications of the technique.
Some alternatives have been presented to minimize this dependence. However, they rely on the addition of extra chemical species to the droplet or its surroundings, which could potentially interact with droplet moieties. Addressing this challenge, our group recently developed Field-DW devices to allow the transport of cells and proteins in DMF, without extra additives.
Here, the protocol for device fabrication and operation is provided, including the electronic interface for motion control. We also continue the studies with the devices, showing that multicellular, relatively large, model organisms can also be transported, arguably unaffected by the electric fields required for device operation.

The protocol for fabrication and operation of field dewetting devices (Field-DW) is described, as well as the preliminary studies of the effects of electric fields on droplet contents.

Digital microfluidics (DMF), a technique for manipulation of droplets, is a promising alternative for the development of &#8220;lab-on-a-chip&#8221; ...

Engineering

Ultrasound Velocity Measurement in a Liquid Metal Electrode

A growing number of electrochemical technologies depend on fluid flow, and often that fluid is opaque. Measuring the flow of an opaque fluid is inherently more difficult than measuring the flow of a transparent fluid, since optical methods are not applicable. Ultrasound can be used to measure the velocity of an opaque fluid, not only at isolated points, but at hundreds or thousands of points arrayed along lines, with good temporal resolution. When applied to a liquid metal electrode, ultrasound velocimetry involves additional challenges: high temperature, chemical activity, and electrical conductivity. Here we describe the experimental apparatus and methods that overcome these challenges and allow the measurement of flow in a liquid metal electrode, as it conducts current, at operating temperature. Temperature is regulated within &#177;2 &#176;C using a Proportional-Integral-Derivative (PID) controller that powers a custom-built furnace. Chemical activity is managed by choosing vessel materials carefully and enclosing the experimental setup in an argon-filled glovebox. Finally, unintended electrical paths are carefully prevented. An automated system logs control settings and experimental measurements, using hardware trigger signals to synchronize devices. This apparatus and these methods can produce measurements that are impossible with other techniques, and allow optimization and control of electrochemical technologies like liquid metal batteries.

Ultrasound velocimetry is used to study mixing by fluid flow in liquid metal electrodes. The focus of this manuscript is to illustrate the methods used for making precise, spatially-resolved ultrasound measurements while limiting oxidation and controlling and monitoring temperature, applied current, and the heater power being supplied.

A growing number of electrochemical technologies depend on fluid flow, and often that fluid is opaque. Measuring the flow of an opaque fluid is inherently ...

Selective Area Modification of Silicon Surface Wettability by Pulsed UV Laser Irradiation in Liquid Environment

The wettability of silicon (Si) is one of the important parameters in the technology of surface functionalization of this material and fabrication of biosensing devices. We report on a protocol of using KrF and ArF lasers irradiating Si (001) samples immersed in a liquid environment with low number of pulses and operating at moderately low pulse fluences to induce Si wettability modification. Wafers immersed for up to 4 hr in a 0.01% H2O2/H2O solution did not show measurable change in their initial contact angle (CA) ~75&#176;. However, the 500-pulse KrF and ArF lasers irradiation of such wafers in a microchamber filled with 0.01% H2O2/H2O solution at 250 and 65 mJ/cm2, respectively, has decreased the CA to near 15&#176;, indicating the formation of a superhydrophilic surface. The formation of OH-terminated Si (001), with no measurable change of the wafer&#8217;s surface morphology, has been confirmed by X-ray photoelectron spectroscopy and atomic force microscopy measurements. The selective area irradiated samples were then immersed in a biotin-conjugated fluorescein-stained nanospheres solution for 2 hr, resulting in a successful immobilization of the nanospheres in the non-irradiated area. This illustrates the potential of&#160;the method for selective area biofunctionalization and fabrication of advanced Si-based biosensing architectures. We also describe a similar protocol of irradiation of wafers immersed in methanol (CH3OH) using ArF laser operating at pulse fluence of 65 mJ/cm2 and in situ formation of a strongly hydrophobic surface of Si (001) with the CA of 103&#176;. The XPS results indicate ArF laser induced formation of Si&#8211;(OCH3)x compounds responsible for the observed hydrophobicity. However, no such compounds were found by XPS on the Si surface irradiated by KrF laser in methanol, demonstrating the inability of the KrF laser to photodissociate methanol and create -OCH3 radicals.

We report on a process of in situ alteration of HF treated Si (001) surface into a hydrophilic or hydrophobic state by irradiating samples in microfluidic chambers filled with&#160;H2O2/H2O solution (0.01%-0.5%) or methanol solutions using pulsed UV laser of a relative low pulse fluence.

The wettability of silicon (Si) is one of the important parameters in the technology of surface functionalization of this material and fabrication of ...

Determining the Chemical Composition of Corrosion Inhibitor/Metal Interfaces with XPS: Minimizing Post Immersion Oxidation

An approach for acquiring more reliable X-ray photoelectron spectroscopy data from corrosion inhibitor/metal interfaces is described. More specifically, the focus is on metallic substrates immersed in acidic solutions containing organic corrosion inhibitors, as these systems can be particularly sensitive to oxidation following removal from solution. To minimize the likelihood of such degradation, samples are removed from solution within a glove box purged with inert gas, either N2 or Ar. The glove box is directly attached to the load-lock of the ultra-high vacuum X-ray photoelectron spectroscopy instrument, avoiding any exposure to the ambient laboratory atmosphere, and thus reducing the possibility of post immersion substrate oxidation. On this basis, one can be more certain that the X-ray photoelectron spectroscopy features observed are likely to be representative of the in situ submerged scenario, e.g. the oxidation state of the metal is not modified.

A protocol to avoid the oxidation of metallic substrates during sample transfer from an inhibited acidic solution to an X-ray photoelectron spectrometer is presented.

An approach for acquiring more reliable X-ray photoelectron spectroscopy data from corrosion inhibitor/metal interfaces is described. More specifically, ...

Aerosol-assisted Chemical Vapor Deposition of Metal Oxide Structures: Zinc Oxide Rods

Whilst columnar zinc oxide (ZnO) structures in the form of rods or wires have been synthesized previously by different liquid- or vapor-phase routes, their high cost production and/or incompatibility with microfabrication technologies, due to the use of pre-deposited catalyst-seeds and/or high processing temperatures exceeding 900 &#176;C, represent a drawback for a widespread use of these methods. Here, however, we report the synthesis of ZnO rods via a non-catalyzed vapor-solid mechanism enabled by using an aerosol-assisted chemical vapor deposition (CVD) method at 400 &#176;C with zinc chloride (ZnCl2) as the precursor and ethanol as the carrier solvent. This method provides both single-step formation of ZnO rods and the possibility of their direct integration with various substrate types, including silicon, silicon-based micromachined platforms, quartz, or high heat resistant polymers. This potentially facilitates the use of this method at a large-scale, due to its compatibility with state-of-the-art microfabrication processes for device manufacture. This report also describes the properties of these structures (e.g., morphology, crystalline phase, optical band gap, chemical composition, electrical resistance) and validates its gas sensing functionality towards carbon monoxide.

Columnar zinc oxide structures in the form of rods are synthesized via aerosol-assisted chemical vapor deposition without the use of pre-deposited catalyst-seed particles. This method is scalable and compatible with various substrates based on either silicon, quartz or polymers.

Whilst columnar zinc oxide (ZnO) structures in the form of rods or wires have been synthesized previously by different liquid- or vapor-phase routes, ...

Preparation and High-temperature Anti-adhesion Behavior of a Slippery Surface on Stainless Steel

Anti-adhesion surfaces with high-temperature resistance have a wide application potential in electrosurgical instruments, engines, and pipelines. A typical anti-wetting superhydrophobic surface easily fails when exposed to a high-temperature liquid. Recently, Nepenthes-inspired slippery surfaces demonstrated a new way to solve the adhesion problem. A lubricant layer on the slippery surface can act as a barrier between the repelled materials and the surface structure. However, the slippery surfaces in previous studies rarely showed high-temperature resistance. Here, we describe a protocol for the preparation of slippery surfaces with high-temperature resistance. A photolithography-assisted method was used to fabricate pillar structures on stainless steel. By functionalizing the surface with saline, a slippery surface was prepared by adding silicone oil. The prepared slippery surface maintained the anti-wetting property for water, even when the surface was heated to 300 &#176;C. Also, the slippery surface exhibited great anti-adhesion effects on soft tissues at high temperatures. This type of slippery surface on stainless steel has applications in medical devices, mechanical equipment, etc.

Slippery surfaces provide a new way to solve the adhesion problem. This protocol describes how to fabricate slippery surfaces at high temperatures. The results demonstrate that the slippery surfaces showed anti-wetting for liquids and a remarkable anti-adhesion effect on soft tissues at high temperatures.

Anti-adhesion surfaces with high-temperature resistance have a wide application potential in electrosurgical instruments, engines, and pipelines. A ...

Simultaneous Multi-surface Anodizations and Stair-like Reverse Biases Detachment of Anodic Aluminum Oxides in Sulfuric and Oxalic Acid Electrolyte

After reporting on the two-step anodization, nanoporous anodic aluminum oxides (AAOs) have been widely utilized in the versatile fields of fundamental sciences and industrial applications owing to their periodic arrangement of nanopores with relatively high aspect ratio. However, the techniques reported so far, which could be only valid for mono-surface anodization, show critical disadvantages, i.e., time-consuming as well as complicated procedures, requiring toxic chemicals, and wasting valuable natural resources. In this paper, we demonstrate a facile, efficient, and environmentally clean method to fabricate nanoporous AAOs in sulfuric and oxalic acid electrolytes, which can overcome the limitations that result from conventional AAO fabricating methods. First, plural AAOs are produced at one time through simultaneous multi-surfaces anodization (SMSA), indicating mass-producibility of the AAOs with comparable qualities. Second, those AAOs can be separated from the aluminum (Al) substrate by applying stair-like reverse biases (SRBs) in the same electrolyte used for the SMSAs, implying simplicity and green technological characteristics. Finally, a unit sequence consisting of the SMSAs sequentially combined with SRBs-based detachment can be applied repeatedly to the same Al substrate, which reinforces the advantages of this strategy and also guarantees the efficient usage of natural resources.

A protocol for fabricating nanoporous anodic aluminum oxides via simultaneous multi-surfaces anodization followed by stair-like reverse biases detachments is presented. It can be applied repeatedly to the same aluminum substrate, exhibiting a facile, high-yield, and environmentally clean strategy.

After reporting on the two-step anodization, nanoporous anodic aluminum oxides (AAOs) have been widely utilized in the versatile fields of fundamental ...

Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications

Several ways to produce superhydrophobic metal surfaces are presented in this work. Aluminum was chosen as the metal substrate due to its wide use in industry. The wettability of the produced surface was analyzed by bouncing drop experiments and the topography was analyzed by confocal microscopy. In addition, we show various methodologies to measure its durability and anti-icing properties. Superhydrophobic surfaces hold a special texture that must be preserved to keep their water-repellency. To fabricate durable surfaces, we followed two strategies to incorporate a resistant texture. The first strategy is a direct incorporation of roughness to the metal substrate by acid etching. After this surface texturization, the surface energy was decreased by silanization or fluoropolymer deposition. The second strategy is the growth of a ceria layer (after surface texturization) that should enhance the surface hardness and corrosion resistance. The surface energy was decreased with a stearic acid film.
The durability of the superhydrophobic surfaces was examined by a particle impact test, mechanical wear by lateral abrasion, and UV-ozone resistance. The anti-icing properties were explored by studying the ability to repeal subcooled water, freezing delay, and ice adhesion.

We illustrate several methodologies to produce superhydrophobic metal surfaces and to explore their durability and anti-icing properties.

Several ways to produce superhydrophobic metal surfaces are presented in this work. Aluminum was chosen as the metal substrate due to its wide use in ...

Metal-Assisted Electrochemical Nanoimprinting of Porous and Solid Silicon Wafers

Metal-assisted electrochemical imprinting (Mac-Imprint) is a combination of metal-assisted chemical etching (MACE) and nanoimprint lithography that is capable of direct patterning 3D micro- and nanoscale features in monocrystalline group IV (e.g., Si) and III-V (e.g., GaAs) semiconductors without the need of sacrificial templates and lithographical steps. During this process, a reusable stamp coated with a noble metal catalyst is brought in contact with a Si wafer in the presence of a hydrofluoric acid (HF) and hydrogen peroxide (H2O2) mixture, which leads to the selective etching of Si at the metal-semiconductor contact interface. In this protocol, we discuss the stamp and substrate preparation methods applied in two Mac-Imprint configurations: (1) Porous Si Mac-Imprint with a solid catalyst; and (2) Solid Si Mac-Imprint with a porous catalyst. This process is high throughput and is capable of centimeter-scale parallel patterning with sub-20 nm resolution. It also provides low defect density and large area patterning in a single operation and bypasses the need for dry etching such as deep reactive ion etching (DRIE).

A protocol for metal-assisted chemical imprinting of 3D microscale features with sub-20 nm shape accuracy into solid and porous silicon wafers is presented.

Metal-assisted electrochemical imprinting (Mac-Imprint) is a combination of metal-assisted chemical etching (MACE) and nanoimprint lithography that is ...

Metal Oxide Heterojunction for Photocatalytic Activities

There is a significant global demand for improvements in synthesis techniques and their optimal characteristics, especially for industrial-scale applications. Sol-gel-based solution combustion synthesis (SG-SCS) is a simple method to produce ordered porous materials. In this regard, Pearson&#39;s hard and soft acids and bases theory assists in selecting host-dopant reactivity to form a proper heterojunction.
The formation of a heterojunction also changes the essential properties of the materials, improving photocatalysis via charge transfer or synergistic activities. A calcination temperature of 500 &#176;C is ideal for this process based on the results of the stability assessment via a differential thermogravimetry ratio analysis (DTG).
The nanoscale dimensions of the nanoparticles (NPs) and nanocomposites (NCs) generated were validated using X-ray diffraction and high-resolution transmission electron microscopy (HRTEM). Furthermore, the scanning electron microscopy micrographs and BET analyses confirmed the porosity nature of the materials. HRTEM, X-ray photoelectron spectroscopy, and energy-dispersive X-ray investigations established the materials composition. The study found that NCs degraded the acid orange 8 (AO8) color more efficiently than bare ZnO.

The development of a heterojunction boosts the photocatalytic activities of solution combustion synthesis, which is a time-/energy-efficient process. Advanced analytical characterization techniques were used in this protocol to evaluate the materials&#39; characteristics, and nanocomposites demonstrated improved acid orange-8 dye degradation.

A Method to Manipulate Surface Tension of a Liquid Metal via Surface Oxidation and Reduction

Samenvatting

Meer video's verkennen